Template:Networking rutos manual leds: Difference between revisions

Revision as of 09:04, 31 August 2020

This page contains information the different types of LEDs and their behaviour on a {{{name}}} router.

Power LED

The power LED is located on the bottom left corner of the front panel, just under the power connector.

[[File:Networking_{{{name}}}}_manual_leds_power_led.png|400px]]

It indicates whether the router is powered on or not

State	Description
LED turned on	Router is powered on
LED turned off	Router is not powered on

Ethernet port LEDs

There are two LEDs located at the top of each Ethernet port.

[[File:Networking_{{{name}}}_manual_leds_ethernet_leds.png|400px]]

They provide information on the current states of the Ethernet ports. Each port has two LEDs:

Orange - 10/100 Mbps connection
Green - 1000 Mbps connection

Below is an explanation on the behaviours of green and orange LEDs.

State	Description
LED on	A data connection on the port is operational (cable plugged in, end device visible, no data is being transferred).
LED off	No data connection on the port is operational (no cable, bad cable or end device not visible for some other reason (such as damaged network card)).
LED blinking	Connection established and data is being transferred over this port.

[[Category:{{{name}}} Manual]]

@@ Line 5: / Line 5: @@
 The <b>power LED</b> is located on the bottom left corner of the front panel, just under the power connector.
-[[File:{{{file_power}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}}_manual_leds_power_led.png|400px]]
 It indicates whether the router is powered on or not
@@ Line 28: / Line 28: @@
 The <b>WiFi band LEDs</b> are located at the bottom of the front panel of the router, to the left of the Ethernet ports.
-[[File:{{{file_wifi}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}_manual_leds_wifi_leds.png|400px]]
 They display whether a WiFi Access Point (AP) is active on a specific band.
@@ Line 59: / Line 59: @@
 The <b>WAN type LEDs</b> are located at the top-right of the front panel.
-[[File:{{{file_wan}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}_manual_leds_wan_leds.png|400px]]
 They indicate which type of Internet connection is currently active.
@@ Line 107: / Line 107: @@
 The <b>Ethernet port LEDs</b> are located on the router's front panel, under each respective Ethernet port.
-[[File:{{{file_ethernet}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|400px]]
 <table class="nd-othertables_3">
@@ Line 133: / Line 133: @@
 |There are two <b>LEDs</b> located at the top of each <b>Ethernet port</b>.
-[[File:{{{file_ethernet}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}_manual_leds_ethernet_leds.png|400px]]
 They provide information on the current states of the Ethernet ports. Each port has two LEDs:
@@ Line 167: / Line 167: @@
 The <b>mobile network type LEDs</b> are located just above the {{{type_sim}}} holder.
-[[File:{{{file_net_type}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}_manual_leds_mobile_network_type_leds.png|400px]]
 They display which type of Internet connection is currently active.
@@ Line 206: / Line 206: @@
 The <b>mobile signal strength indication LEDs</b> are located just above the {{{strength_sim}}} holder.
-[[File:{{{file_signal}}}|400px]]
+[[File:Networking_{{lc:{{{name}}}}}_manual_leds_mobile_signal_strength_leds.png|400px]]
 The number of lit up LEDs represents a different mobile signal strength ([[RSSI]]) value in dBm.