Template:Networking rutos manual mobile: Difference between revisions

Revision as of 09:14, 3 February 2022

Template:Networking rutos manual fw disclosure

Summary

The Mobile page is used to configure mobile connection settings.

This manual page provides an overview of the Mobile page in {{{name}}} devices.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.

General

The General section is used to configure SIM card parameters that define how the device will establish a mobile connection.

Operator settings

The Operator Settings section is used to configure which operators can be allowed (Whitelist) or blocked (Blacklist).

Field	Value	Description
Enable	off \| on; default: off	Enables Whitelist or Blacklist for specified operator list.
Mode	Whitelist \| Blacklist; default: Whitelist	Mode to be applied for operator list. Whitelist - only allow operators in list Blacklist - block all operators in list
Operator list	operator list; default: none	A list of operators which can be configured in Operators List page.

SIM card settings

The SIM Card Settings section is used to configure main SIM card parameters. Refer to the figure and table below for information on the fields contained in that section.

[[File:Networking_{{{series}}}_manual_mobile_general_sim_card_settings.png|border|class=tlt-border]]

Field	Value	Description
Deny data roaming	off \| on; default: off	Denies data connection on roaming conditions.
Service mode	Auto \| ; default: Auto	Network connection type preference.
PIN	integer [0000..99999999]; default: none	SIM card's PIN (Personal Identification Number) is a secret numeric password used to authenticate the device to the SIM card. PIN codes are comprised of numbers only and the length can range from 4 to 8 symbols. PIN number is saved in flash memory therefore it does not reset when default settings are restored.

SMS limit settings

The SMS Limit Settings section provides you with the possibility to set up a maximum sent SMS message cap for your SIM card.

Field	Value	Description
Enable SMS Limit	off \| on; default: off	Turns SMS limiting on or off.
SMS limit count	integer; default: none	Sets the SMS sending cap, i.e., how many SMS messages can be sent from this SIM card during the specified period.
Period	Day \| Week \| Month; default: Day	Period for which SMS limiting should apply. After the period expires, the SMS limit counter will be reset.
Clear SMS Limit	- (interactive button)	Clears the SMS limit counter for the selected period.

Network operators

The Network operators section provides you with the possibility to scan for and manage mobile network operators to which the device's SIM card can connect to.

Field	Value	Description
Current operator	string; default: none	Displays the name of the operator the which the device is currently connected.
Connection mode	Auto \| Manual \| Manual-Auto; default: Auto	Operator selection method. Auto - selects the operator automatically. Manual - requires you to select the operator manually. (More on this selection below.) Manual-Auto - prompts you to enter an operator's code, but if the router can't complete the connection, it will automatically connect to the next available operator.

Manual operator selection

To select an operator manually, specify Connection mode: Manual and click 'Scan For Operators'.

Will be prompted with a pop-up asking if you're sure. Click 'Scan' if you wish to proceed.

Wait for the scan to finish. As indicated by the onscreen message, the process can take up to 3 minutes.

Once the scan has finished, you will see the results in the 'Operators List'.

In order to lock the SIM card to using a single operator, place a check mark next to the relevant entry in the list and click 'Save & Apply'.

Operators list

This section is used to create lists of operators codes, which can then be used in Operator settings section to Whitelist of Blacklist them. Operator code consists of two parts - Mobile Country Code (MCC) and Mobile Network Code (MNC).

By clicking Edit on a list you will be redirected to editing page in which you can enter operator codes for that list.

[[Category:{{{name}}} Network section]]

@@ Line 264: / Line 264: @@
 The <b>Network operators</b> section provides you with the possibility to scan for and manage mobile network operators to which the device's SIM card can connect to. {{#ifeq: {{{dualsim}}} | 1 | {{#ifeq: {{{dualmodem}}} | 0 |Operator selection is only available for the primary SIM card. In order to specify an operator for the other SIM card it must first be selected as the Primary SIM in the [[#SIM card settings|SIM card settings]] section.|}} |}}
-{{#ifeq: {{{dualsim}}} | 1 | [[File:Networking_rutos_manual_mobile_network_operators_scan_dualsim.png|border|class=tlt-border]] |}}
+{{#ifeq: {{{dualsim}}} | 1 | [[File:Networking_rutos_manual_mobile_network_operators_scan_dualsim.png|border|class=tlt-border]] | [[File:Networking_rutos_manual_mobile_network_operators_scan_singlesim.png|border|class=tlt-border]] |}}
 <table class="nd-mantable">
@@ Line 304: / Line 304: @@
 To select an operator manually, specify {{#ifeq: {{{dualmodem}}} | 1 |<b>Modem</b>,<nowiki> </nowiki>|}}<b>Connection mode: <i>Manual</i></b> and click <b>'Scan For Operators'</b>.
-[[File:Networking_rutos_manual_mobile_network_operators_scan_proccess_step_1_dualsim.png|border|class=tlt-border]]
+{{#ifeq: {{{dualsim}}} | 1 | [[File:Networking_rutos_manual_mobile_network_operators_scan_proccess_step_1_dualsim.png|border|class=tlt-border]] | [[File:Networking_rutos_manual_mobile_network_operators_scan_proccess_step_1_singlesim.png|border|class=tlt-border]] |}}
 Will be prompted with a pop-up asking if you're sure. Click 'Scan' if you wish to proceed.