Template:Networking rutos manual bacnet: Difference between revisions
Kristijonasb (talk | contribs) No edit summary |
Gytispieze (talk | contribs) m (Text replacement - "\{\{Template: Networking_rutos_manual_fw_disclosure (.*) (.*) (.*) (.*) \}\}" to "{{Template: Networking_device_manual_fw_disclosure | series = {{{series}}} | name = {{{name}}} | fw_version ={{Template: Networking_device_manual_latest_fw | series = {{{series}}} | name = {{{name}}} }} }}") |
||
| Line 1: | Line 1: | ||
{{Template: | {{Template: Networking_device_manual_fw_disclosure | ||
| fw_version ={{Template: | | series = {{{series}}} | ||
| name = {{{name}}} | |||
| fw_version ={{Template: Networking_device_manual_latest_fw | |||
| series = {{{series}}} | | series = {{{series}}} | ||
| name = {{{name}}} | | name = {{{name}}} | ||
Revision as of 11:11, 24 October 2023
The information in this page is updated in accordance with firmware version .
Summary
BACnet is a communication protocol for building automation and control (BAC) networks that use the ASHRAE, ANSI, and ISO 16484-5 standards protocol.
This manual page provides an overview of the BACnet functionality in {{{name}}} devices.
Note: BACnet is additional software that can be installed from the System → [[{{{name}}} Package Manager|Package Manager]] page.
General Configuration
| Field | Value | Description |
|---|---|---|
| Enable | off | on; default: off | Enables BACnet router function. |
| Enable BBMD | off | on; default: off | Enables BACnet broadcast management function. |
| BBMD interface | network interface; default: eth0 | Specifies interface for BBMD function. IP address of this interface should be reachable from WAN. |
| Port forward | off | on; default: off | Creates port forward firewall rule to make application port in LAN reachable from selected BBMD interface. |
| Force gateway | off | on; default: off | Adds configured gateway IP address and port to BBMD packages sent. |
| Gateway address | ip4; default: none | Gateway IP address. |
| Gateway port | integer [1..65535]; default: none | Gateway port number. |
BIP Configuration
Communications in BACnet over IP (BIP) rely upon the protocol rules of IP and Ethernet.
| Field | Value | Description |
|---|---|---|
| BIP port | integer [1..65535]; default: 47808 | BIP UDP port. |
MSTP Configuration
MSTP is most commonly used to connect field devices to controllers / routers / control applications. The physical layer uses RS485 which allows up to 31 devices to be installed on a single network.
| Field | Value | Description |
|---|---|---|
| MSTP MAC | integer [0..127]; default: 13 | Router MSTP MAC address. |
| MSTP MAC max | integer [1..127]; default: 127 | Maximum client address in the MSTP network. |
| Baud rate | 300 | 600 | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600 | 115200 | 230400; default: 38400 | Serial data transmission rate (in bits per second). |
| Parity | Even | Odd | Mark | Space | None; default: None | In serial transmission, parity is a method of detecting errors. An extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check.
|
| Data bits | 5 | 6 | 7 | 8; default: 8 | Number of data bits for each character. |
| Stop bits | 1 | 2; default: 1 | Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. Two stop bits are required if slow electromechanical devices are used.. |
[[Category:{{{name}}} Services section]]