RUT230 QoS: Difference between revisions
No edit summary |
|||
| Line 21: | Line 21: | ||
<tr> | <tr> | ||
<td>Enable</td> | <td>Enable</td> | ||
<td>yes | <td>yes | no; Default: '''no'''</td> | ||
<td>Toggles QoS functionality ON or OFF</td> | <td>Toggles QoS functionality ON or OFF</td> | ||
</tr> | </tr> | ||
| Line 29: | Line 29: | ||
<tr> | <tr> | ||
<td>Interface</td> | <td>Interface</td> | ||
<td>WAN | <td>WAN | LAN | PPP; Default: '''WAN'''</td> | ||
<td>Interface that the rule applies to</td> | <td>Interface that the rule applies to</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Enable</td> | <td>Enable</td> | ||
<td>yes | <td>yes | no; Default: '''no'''</td> | ||
<td>Toggles the rule ON or OFF</td> | <td>Toggles the rule ON or OFF</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Calculate overhead</td> | <td>Calculate overhead</td> | ||
<td>yes | <td>yes | no; Default: '''no'''</td> | ||
<td>Decreases upload and download ratio to prevent link saturation</td> | <td>Decreases upload and download ratio to prevent link saturation</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Half-duplex</td> | <td>Half-duplex</td> | ||
<td>es | <td>es | no; Default: '''no'''</td> | ||
<td>Enables data transmission in both directions on a single carrier</td> | <td>Enables data transmission in both directions on a single carrier</td> | ||
</tr> | </tr> | ||
| Line 71: | Line 71: | ||
<tr> | <tr> | ||
<td>Target</td> | <td>Target</td> | ||
<td>Priority | <td>Priority | Express | Normal | Low; Default: '''WAN'''</td> | ||
<td>Target for which the rule will be applied</td> | <td>Target for which the rule will be applied</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Source host</td> | <td>Source host</td> | ||
<td>All | <td>All | ip; Default: '''All'''</td> | ||
<td>Host from which data will be transmitted</td> | <td>Host from which data will be transmitted</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Destination host</td> | <td>Destination host</td> | ||
<td>All | <td>All | ip; Default: '''All'''</td> | ||
<td>Host to which data will be transmitted</td> | <td>Host to which data will be transmitted</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Protocol</td> | <td>Protocol</td> | ||
<td>All | <td>All | TCP | UDP | ICMP | -- custom --; Default: '''All'''</td> | ||
<td>Data transmission protocol</td> | <td>Data transmission protocol</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Ports</td> | <td>Ports</td> | ||
<td>All | <td>All | integer [0..65535]; Default: '''22,53'''</td> | ||
<td>Port(s) that will be used for transmission. You can enter multiple ports by separating them by commas (',')</td> | <td>Port(s) that will be used for transmission. You can enter multiple ports by separating them by commas (',')</td> | ||
</tr> | </tr> | ||
| Line 100: | Line 100: | ||
</tr> | </tr> | ||
</table> | </table> | ||
[[Category:RUT230 WebUI]] | |||
Revision as of 08:51, 1 March 2019
Main Page > EOL Products > RUT230 > RUT230 Manual > RUT230 WebUI > RUT230 Services section > RUT230 QoSSummary
With QoS you can prioritize network traffic selected by addresses, ports or services. This chapter is an overview of the QoS function in RUT routers.
General settings and Interfaces
The General settings section is used to enable or disable all QoS functionality and the Interfaces section allows you to set up bandwidth limits for specified network interfaces.
| GENERAL SETTINGS | ||
| field name | value | description |
|---|---|---|
| Enable | yes | no; Default: no | Toggles QoS functionality ON or OFF |
| INTERFACES | ||
| Interface | WAN | LAN | PPP; Default: WAN | Interface that the rule applies to |
| Enable | yes | no; Default: no | Toggles the rule ON or OFF |
| Calculate overhead | yes | no; Default: no | Decreases upload and download ratio to prevent link saturation |
| Half-duplex | es | no; Default: no | Enables data transmission in both directions on a single carrier |
| Download speed (kbit/s) | integer; Default: 1024 | Specifies maximum download speed for the specified interface |
| Upload speed (kbit/s) | integer; Default: 128 | Specifies maximum upload speed for the specified interface |
Classification Rules
| field name | value | description |
|---|---|---|
| Target | Priority | Express | Normal | Low; Default: WAN | Target for which the rule will be applied |
| Source host | All | ip; Default: All | Host from which data will be transmitted |
| Destination host | All | ip; Default: All | Host to which data will be transmitted |
| Protocol | All | TCP | UDP | ICMP | -- custom --; Default: All | Data transmission protocol |
| Ports | All | integer [0..65535]; Default: 22,53 | Port(s) that will be used for transmission. You can enter multiple ports by separating them by commas (',') |
| Number of bytes | integer; Default: " " | The maximum number of bytes for the connection |