Template:Networking rut manual modbus

Summary

Modbus is a serial communications protocol. Simple and robust, it has since become a de facto standard communication protocol and is now a commonly available means of connecting industrial electronic devices. This chapter is an overview of the Modbus TCP functionality.

Modbus TCP

Modbus TCP provides users with the possibility to set or get system parameters. The Modbus daemon acts as slave device. That means it accepts connections from a master (client) and sends out a response or sets some system related parameter in accordance with the given query.

The figure below is an example of the Modbus TCP window section and the table below provides information on the fields contained in that window:

[[File:{{{modbus_tcp_file}}}]]

Get Parameters

---

Modbus parameters are held within registers. Each register contains 2 bytes of information. For simplification, the number of registers for storing numbers is 2 (4 bytes), while the number of registers for storing text information is 16 (32 bytes). The register numbers and corresponding system values are described in the table below:

{{Template: Networking_{{{name}}}_manual_modbus_modbus_tcp_get_parameters_table}}

Set Parameters

---

The Modbus daemon can also set some device parameters. These parameters and explanations on how to use them are described in the table below:

{{Template: Networking_{{{name}}}_manual_modbus_modbus_tcp_set_parameters_table}}

* All ON/OFF commands only accept 0 and 1 values, which represent the following:

• 1 - ON
• 0 - OFF

Modbus TCP Master

A Modbus master device can request data from Modbus slaves. The Modbus TCP Master section is used to configure Modbus TCP slaves. To add a new slave, enter a custom name, slave's ID, IP address and port and click the "Add" button:

[[File:{{{file_add_new_slave}}}]]

• Alarms - Redirects you to the slave's alarm configuration page (more information in [[{{{name}}} Modbus#Alarm_configuration|section 3.3)
• Clone - Creates an identical slave configuration

Button	Description
Alarms	Redirects you to the slave's alarm configuration page (more information in [[{{{name}}} Modbus#Alarm_configuration|section 3.3)
Clone	Creates an identical slave configuration

Slave device configuration

---

The figure below is an example of the Slave device configuration and the table below provides information on the fields contained in that section:

[[File:{{{file_slave_configuration}}}]]

Field name	Value	Description
Enabled	yes | no; Default: no	Turns communication with the slave device ON or OFF
Name	string; Default: none	Slave device custom name, used for easier management purposes
Slave ID	integer [1..255]; Default: none	Slave ID. Each slave in a network is assigned a unique identifier randging from 1 to 255. When the master requests data from a slave, the first byte it sends is the Slave ID
IP address	ip; Default: none	Slave device IP address
Port	integer [0..65535]; Default: none	Slave device Modbus TCP port
Period	integer [1..6400]; Default: none	Interval at which requests are sent to the slave device
Timeout	integer [1..30]; Default: none	Maximum response wait time

Requests configuration

---

A Modbus request is way of obtaining data from Modbus slaves. The master a sends a request to a slave specifying which Modbus registers should be read. The slave then sends the requested data back to the Modbus master.

The figure below is an example of the Requests configuration section and the table below provides information contained in the fields of that section:

[[File:{{{file_requests}}}]]

Field name	Value	Description
Name	string; Default: Unnamed Parameter	Request name. Used for easier management purposes
Data type	8bit INT | 8bit UINT | 16bit INT, high byte first | 16bit INT, low byte first | 16bit UINT, high byte first | 16bit UINT, low byte first | 32bit float, Byte order 1,2,3,4 | 32bit float, Byte order 4,3,2,1 | 32bit float, Byte order 2,1,4,3 | 32bit float, Byte order 3,4,1,2; Default: 16bit INT, high byte first	Type of data contained in Modbus registers
Function	1 | 2 | 3 | 4 | 5 | 15 | 16; Default: 3
First Register	integer [0..65535]; Default: 1	First Modbus register from which data will be read
Number of Registers	integer [1..2000]; Default: none	Number of Modbus registers that will be read during the request
Enabled	yes | no; Default: no	Turns the request ON or OFF
Test	- (interactive button)	Generates a Modbus request according to given parameters in order to test the request configuration. You must first save the configuration before you can use the Test button
Delete	- (interactive button)	Deletes the request
Add	- (interactive button)	Adds a new request request

Alarm configuration

---

Alarms are way of

[[File:{{{file_alarms}}}]]

Field name	Value	Description
Enabled	yes | no; Default: no	Turns the alarm ON or OFF
Function code	Read Coil Status (1) | Read Input Status (2) | Read Holding Registers (3) | Read Input Registers (4); Default: Read Coil Status (1)
Register	integer [0..65535]; Default: none
Condition	More than | Less than | Equal to | Not Equal to; Default: Equal to
Value	various; Default: none
Action	SMS | Trigger output | Modbus Request; Default: SMS
SMS: Message	string; Default: none	SMS message text
SMS: Phone number	phone number; Default: none	recipient's phone number
Trigger output: Output	Open collector output | Relay output | Both; Default: Open collector output	Which output will be triggered
Trigger output: I/O Action	Turn On | Turn Off | Invert; Default: Turn On	Action that will taken on the specified output
Modbus Request: IP address	ip | host; Default: none	Modbus slave's address
Modbus Request: Port	integer [0..65535]; Default: none	Modbus slave's port
Modbus Request: Timeout	integer [1..30]; Default: 5	Maximum time to wait for a response
Modbus Request: ID	integer [1..255]; Default: none	Modbus slave ID
Modbus Request: Modbus function	Read Coil Status (1) | Read Input Status (2) | Read Holding Registers (3) | Read Input Registers (4) | Force Single Coil (5) | Preset Single Register (6) | Force Multiple Coils (15) | Force Multiple Registers (16); Default: Force Single Coil (5)
Modbus Request: First register	integer [0..65535]; Default: none	Begins reading from the register specified in this field
Modbus Request: Number of registers	integer [0..65535]; Default: none

Modbus Data to Server

The Modbus Data to Server function provides you with the possibility to set up senders that transfer data collected from Modbus slaves to remote servers. To add a new data sender, enter the server's address, specify the data sending period and click the "Add" button:

[[File:{{{file_add_new_sender}}}]]

Data sender configuration

---

When you add a new data sender, you will redirected to its configuration window. The figure below is an example of that window and the table below provides information on the fields that it contains:

[[File:{{{file_sender_configuration}}}]]

Enabled	yes | no; Default: no	Turns the data sender ON or OFF
Name	string; Default: none	Data sender's name. used for easier management purposes
Protocol	HTTP(S); Default: HTTP(S)	Data sending protocol
JSON format	string; Default: {"ID":"%i", "TS":"%t","ST":"%s","VR":"%a"}
Segment count	1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10; Default: 1
URL	host | ip; Default: none	Address of the server to which the data will be sent
Period	integer [1..6400]; Default: none	Data sending frequency (in seconds)
Data filtering	All data | By slave ID | By slave IP; Default: All data
Retry on fail	yes | no; Default: no	Specifies whether the data sender should retry failed attempts
Custom header	string; Default: no

See also

[[Category:{{{name}}} WebUI]]