Template:Networking rutos configuration example guest wifi: Difference between revisions

From Teltonika Networks Wiki
Line 95: Line 95:
</table>
</table>


===New LAN Interface===
===New LAN interface===
----
----



Revision as of 16:36, 21 July 2020

Introduction

Most of us are aware, that network security is extremely important. If your WiFi network is not properly secured, it makes you and all of your home or office resources vulnerable to a variety of security threats. To stay ahead of the curve, many companies and home users have guest WiFi. Unlike your regular WiFi network that you or your company members use, the guest WiFi network restricts what your guests can do in your network. It gives visitors access to the Internet connection, but nothing else making you or your company a lot more secure. This chapter is a guide on configuring a guest WiFi.

Configuring router (RUTX)

Before you start configuring the router turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.


New WiFi AP


Login to the router's WebUI, navigate to the Network → Wireless page and do the following:

  1. Click Add.

On General Setup tab do the following:

  1. Enable instance.
  2. Select mode Access Point.
  3. Enter ESSID.
  4. Expand the drop-down menu Network.
  5. Uncheck the lan interface.
  6. Create a new interface, enter name Guest.

Switch to Wireless Security tab and do the following:

  1. Select Encryption type.
  2. Select Cipher type.
  3. Enter Key.
  4. Save&Apply changes.

Wait for configuration to apply. Two Wireless Access Points should be enabled

New LAN interface


Navigate to the Network → Interfaces page and do the following:

  1. Find new interface called GUEST and click the Edit button.

In the General setup section, do the following:

  1. Select Protocol - Static. Confirm by clicking "SWITCH PROTOCOL".
  2. Enter a IPv4 address.
  3. Enter a IPv4 netmask.
  4. Enable DHCP server.
  5. Press Save&Apply.

Edit Firewall


Navigate to the Network → Firewall → General Settings page and do the following:

  1. Click the Add button.

In the ZONE page, do the following:

  1. Enter a custom Name.
  2. Add new created "Guest" LAN to Covered networks.
  3. Select WAN interfaces for Allow forward to destination zones.
  4. Select WAN interfaces for Allow forward from destination zones.
  5. Save&Apply changes.

To disable Web UI or SSH access to RUTX from Guest's_WiFi network navigate to the Network → Firewall → Traffic Rules page and do the following:

  1. Enter a custom Name.
  2. Select "guest_zone" for Source zone.
  3. Select "lan" for Destination zone.
  4. Click the Add button.

In the TRAFFIC RULES page, do the following:

  1. Enable instance.
  2. Change the Destination zone to "Device (input)".
  3. Enter the Destination port to reject. By default ports 22, 80, 443 are used to access the web user interface and SSH.
  4. Change the Action to "Reject".
  5. Save&Apply changes.

Results

If you've followed all the steps presented above, your configuration should be finished. If you are near a RUT, that is, in a wireless zone, turn on WiFi on your device and view the available networks. You should see the available SSID - "RUT_WiFi" and "Guest_WiFi". Select one of them and enter the appropriate WiFi password.

Wireless users connected to SSID: “RUTX_WIFI”, will be assign to “LAN”, and will get IP from main pool 192.168.1.0/24.

Wireless users connected to SSID: “GUEST'S_WIFI”, will be assign to LAN “Guest”, and will get IP from new pool 10.10.10.0/24.

Guest hosts are unable to access any data from pool 192.168.1.0/24.