Line 1,587: |
Line 1,587: |
| </table> | | </table> |
| | | |
| + | ==L2TPv3== |
| + | |
| + | L2TPv3 (Layer Two Tunneling Protocol Version 3) is a point-to-point layer two over IP tunnel. This means you can tunnel L2 protocols like Ethernet, Frame-relay, ATM, HDLC, PPP, etc. over an IP network. |
| + | |
| + | ===Local settings=== |
| + | ---- |
| + | [[File:Networking_rutos_vpn_l2tpv3_configuration_local_settings_v1.png]] |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Enable</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Turns the L2TPv3 instance on or off.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Local address</td> |
| + | <td>ip; default: <b>none</b></td> |
| + | <td>IP address of device's WAN. Note: If left empty, it will take IP address automatically from main WAN interface. <td> |
| + | </tr> |
| + | <tr> |
| + | <td>Tunnel ID</td> |
| + | <td>integer [1..4294967295]; default: <b>none</b></td> |
| + | <td>Uniquely identifies the tunnel. The value used must match the peer tunnel ID value being used at the peer.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Session ID</td> |
| + | <td>integer [1..4294967295]; default: <b>none</b></td> |
| + | <td>The value used must match the tunnel ID value being used at the peer.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Cookie</td> |
| + | <td>string; default: <b>none</b></td> |
| + | <td>Must be specified in hexidecimal form and be length of 8 or 16. eg.: 89ABCDEF.</td> |
| + | </tr> |
| + | </table> |
| + | |
| + | ===Peer settings=== |
| + | ---- |
| + | [[File:Networking_rutos_vpn_l2tpv3_configuration_peer_settings_v1.png]] |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Peer address</td> |
| + | <td>ip; default: <b>none</b></td> |
| + | <td>Peer Endpoint IP address.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Peer Tunnel ID</td> |
| + | <td>integer [1..4294967295]; default: <b>none</b></td> |
| + | <td>ID of peer's tunnel is specified from 1 to 4294967295. It must match other end tunnel ID.<td> |
| + | </tr> |
| + | <tr> |
| + | <td>Peer Session ID</td> |
| + | <td>integer [1..4294967295]; default: <b>none</b></td> |
| + | <td>UID of peer's session is specified from 1 to 4294967295. It must match other end session ID. </td> |
| + | </tr> |
| + | <tr> |
| + | <td>Peer Cookie</td> |
| + | <td>string; default: <b>none</b></td> |
| + | <td>Must be specified in hexidecimal form and be length of 8 or 16. eg.: 89ABCDEF. It must match other end Cookie.</td> |
| + | </tr> |
| + | </table> |
| + | |
| + | ===Instance Settings=== |
| + | ---- |
| + | [[File:Networking_rutos_vpn_l2tpv3_configuration_instance_settings_v1.png]] |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Bridge to</td> |
| + | <td>None {{!}} LAN; default: <b>None</b></td> |
| + | <td>Peer Endpoint IP address.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>IP Address</td> |
| + | <td>ip; default: <b>none</b></td> |
| + | <td>IP address of standalone L2TPv3 interface.<td> |
| + | </tr> |
| + | <tr> |
| + | <td>Netmask</td> |
| + | <td>netmask; default: <b>none</b></td> |
| + | <td>Netmask of standalone L2TPv3 interface. </td> |
| + | </tr> |
| + | <tr> |
| + | <td>MTU</td> |
| + | <td>integer [64..9000]; default: <b>none</b></td> |
| + | <td>Sets the maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Encapsulation</td> |
| + | <td>IP {{!}} UDP; default: <b>IP</b></td> |
| + | <td>Specify technology to use when connecting to other end.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Layer 2 specific header type</td> |
| + | <td>None {{!}} Linux Default; default: <b>Linux Default</b></td> |
| + | <td>It might be neccessary to set this option to none when using other hardware.</td> |
| + | </tr> |
| + | </table> |
| ==WireGuard== | | ==WireGuard== |
| | | |