Domnev

The information in this page is updated in accordance with 00.07.03.1 firmware version .

Introduction

This article contains instructions on how to send M-Bus data to the server using various protocols.

Configuration overview and prerequisites

Before we begin, let's take a look at the configuration that we are attempting to achieve and the prerequisites that make it possible.

Prerequisites:

• TRB143;
• M-Bus device;
• Server;
• An end device (PC, Laptop, Tablet, Smartphone) for configuration;

If you're having trouble finding any page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode," which is located at the top-right corner of the WebUI.

Node-RED installation and setup

We are going to set up Node-RED in Linux virtual machine. For Node-RED to work, you would need to install Node.js version 14.00 or higher, if you already have Node.js installed, verify Node.js version using this command:

node -v

If you do not have Node.js installed, run these commands to install it:

sudo apt install curl
curl -fsSL https://deb.nodesource.com/setup_14.x | sudo -E bash –
sudo apt-get install -y nodejs

Once we have Node.js installed, we can install Node-RED. Use this command to install:

sudo npm install -g –unsafe-perm node-red

Use the command node-red to start a local server. Here is how the terminal should look like if the server starts correctly:

---

Once you have the local server running, use the local IP and port number in your internet browser. In this case, we are using 127.0.0.1:1880:

For MQTT usage, we are going to need MQTT-specific nodes. Use the side menu to navigate to Manage Palette section and install these nodes:

• node-red-contrib-aedes
• node-red-contrib-mqtt-broker

Configuration

M-Bus Data to Server via MQTT

This sections contains information on how to send M-Bus data to the server on Node-RED using MQTT protocol.

Data to Server configuration

---

1. Enable instance;
2. Name: enter desired instance name;
3. Data source: M-bus;
4. Protocol: MQTT;
5. JSON format: enter what data you would like to send;
6. URL/Host/Connection string: enter address of server;
7. Port: enter server port;
8. Topic: enter desired topic name;

M-Bus configuration

---

1. Enable M-Bus;
2. Enter desired instance name;
3. Add;

File:M bus instance configuration.png

1. Enable instance;
2. Period: enter desired period;
3. BLOGAS - NAME NEREIKIA

File:M bus slave configuration.png

1. Enable request configuration;
2. Slave address: enter desired slave address;
3. Data type: select desired data type (this time we will be using XML);
4. Save & apply changes.

Node-RED configuration

---

Below you can see Node-Red block diagram that is used to receive data:

• aedes broker
• MQTT in
• Debug

---

File:Node-red-broker-configuration.png

File:Node-red-debug-config.png

MQTT Port: 1883; WS Bind: port; Done; Everything else can be left as default.

Output: msg. payload; To: debug window; Done; Everything else can be left as default.

---

Results

---

M-Bus Data to Server Via HTTP

This sections contains information on how to send M-Bus data to the server on Node-RED using HTTP protocol.

---

---

M-Bus configuration

---

1. Enable request configuration;
2. Slave address: enter desired slave address;
3. Data type: select desired data type (this time we will be using HEX);
4. Save & apply changes.

---

Results

---

MQTT broker

MQTT Broker is an entity that listens for connections on the specified port and relays received messages to MQTT client.

---

MQTT broker configuration

---

---

---

Results

---

See Also

• M-Bus
• Data to Server
• MQTT Broker