General commands TRM250
The command delivers a product information text.
2.1 ATI Display Product Identification Information - page 12
The command returns a manufacturer identification text. See also AT+CGMI.
2.2 AT+GMI Request Manufacturer Identification - page 13
The command returns a product model identification text. It is identical with AT+CGMM.
2.3 AT+GMM Request TA Model Identification - page 13
The command delivers a product firmware version identification text. It is identical with AT+CGMR.
2.4 AT+GMR Request TA Revision Identification of Software Release - page 14
The command returns a manufacturer identification text. See also AT+GMI.
2.5 AT+CGMI Request Manufacturer Identification - page 14
The command returns a product model identification text. It is identical with AT+GMM.
2.6 AT+CGMM Request Model Identification - page 15
The command delivers a product firmware version identification text. It is identical with AT+GMR.
2.7 AT+CGMR Request TA Revision Identification of Software Release - page 15
The command returns the International Mobile Equipment Identity (IMEI) number of ME. It is identical with AT+CGSN.
The command returns International Mobile Equipment Identity (IMEI) number of ME. It is identical with AT+GSN.
The command resets AT command settings to their factory default values.
The command displays the current settings of several AT command parameters, including the single-letter AT command parameters which are not readable otherwise.
BG96 AT Commands Manual V2.3.pdf#page=19 2.11 AT&V Display Current Configuration - page 18
The command stores the current AT command settings to a user defined profile in non-volatile memory.
The command restores the current AT command settings to the user defined profile in non-volatile memory, if one was stored with AT&W before. Any additional AT command on the same command line may be ignored.
The command controls whether the result code is transmitted to the TE. Other information text transmitted as response is not affected.
BG96 AT Commands Manual V2.3.pdf#page=21 2.14 ATQ Set Result Code Presentation Mode - page 20
The command determines the contents of header and trailer transmitted with AT command result codes and information responses.
The result codes, their numeric equivalents and brief descriptions of the use of each are listed in the following table.
BG96 AT Commands Manual V2.3.pdf#page=21 2.15 ATV TA Response Format - page 20
The command controls whether or not the module echoes characters received from TE during AT command mode.
BG96 AT Commands Manual V2.3.pdf#page=23 2.16 ATE Set Command Echo Mode - page 22
The command repeats previous AT command line, and “/” acts as the line terminating character.
BG96 AT Commands Manual V2.3.pdf#page=23 2.17 A/ Repeat Previous Command Line - page 22
The command determines the character recognized by the module to terminate an incoming command line. It is also generated for result codes and information text, along with character value set via ATS4
BG96 AT Commands Manual V2.3.pdf#page=24 2.18 ATS3 Set Command Line Termination Character - page 23
The command determines the character generated by the module for result code and information text, along with the command line termination character set via ATS3.
BG96 AT Commands Manual V2.3.pdf#page=25 2.19 ATS4 Set Response Formatting Character - page 24
The command determines the character value used by the module to delete the immediately preceding character from the AT command line (i.e. equates to backspace key).
BG96 AT Commands Manual V2.3.pdf#page=25 2.20 ATS5 Set Command Line Editing Character - page 24
The command determines whether or not the module transmits particular result codes to the TE. It also controls whether or not the module verifies the presence of a dial tone when it begins dialing, and whether or not engaged tone (busy signal) detection is enabled.
The command controls the functionality level. It can also be used to reset the UE.
BG96 AT Commands Manual V2.3.pdf#page=27 2.22 AT+CFUN Set Phone Functionality - page 26
The command controls the format of error result codes: ERROR, error numbers or verbose messages as +CME ERROR: <err> and +CMS ERROR: <err>.
BG96 AT Commands Manual V2.3.pdf#page=28 2.23 AT+CMEE Error Message Format - page 27
The Write Command informs the module which character set is used by the TE. This enables the UE to convert character strings correctly between TE and UE character sets.
BG96 AT Commands Manual V2.3.pdf#page=29 2.24 AT+CSCS Select TE Character Set - page 28
The command is used to configure the output port of URC.
BG96 AT Commands Manual V2.3.pdf#page=30 2.25 AT+QURCCFG Configure URC Indication Option - page 29