RUT900 TR-069

From Teltonika Networks Wiki
Revision as of 13:10, 6 December 2018 by Dziugas (talk | contribs) (Created page with "==Summary== '''TR-069 (Technical Report 069)''' is a technical specification of the Broadband Forum that defines an application layer protocol for remote management of custom...")

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)
Main Page > EOL Products > RUT900 > RUT900 Manual > RUT900 WebUI > RUT900 Services section > RUT900 TR-069

Summary

TR-069 (Technical Report 069) is a technical specification of the Broadband Forum that defines an application layer protocol for remote management of customer-premises equipment (CPE) connected to an Internet Protocol (IP) network. This section is a summary of TR-069 in RUT routers.

TR-069 Client Configuration

FIELD NAME VALUE DESCRIPTION
Enable yes | no; Default: no Toggles TR-069 client ON or OFF
Periodic enable yes | no; Default: yes Toggles periodic transmissions of data to server ON or OFF
Accept server request yes | no; Default: no When enabled, the router accepts connection requests from server
Sending interval integer [60..9999999]; Default: 100 Periodic data transmission interval
Username string; Default: easycwmp User name used for authentication on a TR-069 server
Password string; Default: " " Password used for authentication on a TR-069 server
URL host | ip; Default: http://192.168.1.110:8080/openacs/acs TR-069 server’s address

Management via TR-069

TR-069 can be used to set or get values from RUT routers. Below is a list of commands used for router management via TR-069.

  • R - Read only
  • RW - Read/Write
  • string(64) - 64 bit string
  • string(256) - 256 bit string
  • unsignedInt - integer storing only positive values

FW Upgrade:

 1. FileType - 1- Firmware Upgrade Image, string(64)
 2. URL - URL, specifying the source file location, string(256) 
 3. Username - Username to be used by the CPE to authenticate with the file server. This string is set to the empty string if no authentication is required, string(256) 
 4. Password - Password to be used by the CPE to authenticate with the file server. This string is set to the empty string if no authentication is required, string(256)
 5. FileSize - The size of the file to be downloaded in bytes, unsignedInt 

Device Information:

 1. DeviceInfo.SpecVersion - R
 2. DeviceInfo.ProvisioningCode - RW
 3. DeviceInfo.Manufacturer - Device manufacturer (e.g., Teltonika) R
 4. DeviceInfo.ManufacturerOUI - R
 5. DeviceInfo.ProductClass - Device model (e.g., RUT955) R
 6. DeviceInfo.SerialNumber - Device serial number (e.g., 09547785) R
 7. DeviceInfo.HardwareVersion - Device hardware version (e.g., 0505) R
 8. DeviceInfo.SoftwareVersion - Device software version (e.g., RUT9XX_R_00.03.816) R
 9. DeviceInfo.UpTime - Router uptime R
 10. DeviceInfo.DeviceLog - Last line of device log. R
 11. DeviceInfo.MemoryStatus
   11.1 DeviceInfo.MemoryStatus.Total - Total device memory (e.g., 61008) R
   11.2 DeviceInfo.MemoryStatus.Free - Free memory (e.g., 24224) R

IP Ping Diagnostics support:

 1. IPPingDiagnostics
   1.1 IPPingDiagnostics.DiagnosticsState - Diagnostics State (e.g. None) R
   1.2 IPPingDiagnostics.Host - Host RW
   1.3 IPPingDiagnostics.NumberOfRepetitions - Number Of Repetitions RW
   1.4 IPPingDiagnostics.Timeout - Timeout RW
   1.5 IPPingDiagnostics.DataBlockSize - Data block size RW
   1.6 IPPingDiagnostics.SuccessCount - Success count R
   1.7 IPPingDiagnostics.FailureCount - Fail count R
   1.8 IPPingDiagnostics.AverageResponseTime - Average Response Time R
   1.9 IPPingDiagnostics.MinimumResponseTime - Minimum Response Time R
   1.10 IPPingDiagnostics.MaximumResponseTime - Maximum Response Time R

Mobile Information:

 1.MobileInfo:
   1.1 MobileInfo.RSSI - GSM signal level R
   1.2 MobileInfo.ConnState - Connection state R
   1.3 MobileInfo.NetState - Network link state R
   1.4 MobileInfo.ICCID - SIM ICCID R
   1.5 MobileInfo.IMSI - IMSI R
   1.6 MobileInfo.RSCP - RSCP level R
   1.7 MobileInfo.ECIO - ec/io level R
   1.8 MobileInfo.RSRP - RSRP level R
   1.9 MobileInfo.SINR - SINR level R
   1.10 MobileInfo.RSRQ - RSRQ level R
   1.11 MobileInfo.CellID - CellID R
   1.12 MobileInfo.Operator - Name of operator used R
   1.13 MobileInfo.OperatorNum - Operator number R
   1.14 MobileInfo.ConnType - Data carrier type R
   1.15 MobileInfo.Modem
     1.15.1 MobileInfo.Modem.Model - Modem model R
     1.15.2 MobileInfo.Modem.Manufacturer - Modem manufacturer R
     1.15.3 MobileInfo.Modem.Serial - Modem serial number R
     1.15.4 MobileInfo.Modem.Revision - Modem revision number R
     1.15.5 MobileInfo.Modem.IMEI - Modem IMEI R
     1.15.6 MobileInfo.Modem.SimState - SIM car state R
     1.15.7 MobileInfo.Modem.PinState - PIN state R
     1.15.8 MobileInfo.Modem.Temperature - Modem temperature in 0.1 degrees Celcius R
 1.16 MobileInfo.SentToday - Bytes sent today R
 1.17 MobileInfo.ReceivedToday - Bytes received today R
 1.18 MobileInfo.SentThisMonth - Bytes sent this month R
 1.19 MobileInfo.ReceivedThisMonth - Bytes received this month R

WAN Information:

 1. WANConnectionDevice
   1.1 WANConnectionDevice.WANIPConnection
     1.1.1 WANConnectionDevice.WANIPConnection.ConnectionStatus - Connection status (e.g., Connected) R
     1.1.2 WANIPConnection.ExternalIPAddress - IP address R
     1.1.3 WANIPConnection.MACAddress - MAC address R
   1.2 WANConnectionDevice.WANPPPConnection - PPP connection
     1.2.1. WANConnectionDevice.WANPPPConnection.1.Enable - Conection state (e.g., 1 or 0) R
     1.2.2. WANConnectionDevice.WANPPPConnection.1.APN - APN R
     1.2.3. WANConnectionDevice.WANPPPConnection.1.ExternalIPAddress - IP address R

Wi-Fi Information:

 1. Radio
   1.2 Radio.Enable - Enabled (e.g., 0 or 1) RW
   1.3 Radio.Status - Wifi status (e.g., Up) R
   1.4 Radio.Name - Device name R
   1.5 Radio.SupportedFrequencyBands - Supported frequency bandss (e.g., 2.4GHz) R
   1.6 Radio.OperatingFrequencyBand - Operating frequency bandss (e.g., 2.4GHz) R
   1.7 Radio.ChannelsInUse - Channels R
   1.8 Radio.Channel - Channel in use RW
   1.9 Radio.AutoChannelSupported - Auto channel support (e.g., 1) R
   1.10 Radio.AutoChannelEnable - Auto channel state (e.g., 1) RW
   1.11 Radio.OperatingStandards - Operating standards (e.g., 11ng) RW
 2. SSID
   2.1 SSID.Enable - Wifi interface state (e.g., 1) RW
   2.2 SSID.Status - Wifi interface status (e.g., 1) R
   2.3 SSID.Name - Interface name (e.g., wlan0 ) R
   2.4 SSID.SSID - SSID RW
 3. Security
   3.5 Security.ModesSupported - (None,WEP-64,WEP-128,WPA-Personal,WPA2-Personal,WPA-WPA2-Personal,WPA-Enterprise,WPA2-Enterprise,WPA-WPA2-Enterprise) R
   3.6 Security.ModeEnabled - Current mode (e.g WPA2-Personal) RW
   3.7 Security.WEPKey - WEP Key RW
   3.8 Security.PreSharedKey - Pre shared key RW
   3.9 Security.KeyPassphrase - Key passphrase RW

Hotspot Information:

 1. General
   1.1 General.Enable - State (e.g. 1) RW
   1.2 General.IP - IP address (e.g. 192.168.2.254) RW
   1.3 General.Mode - Authentication mode
         (extrad - External radius, intrad - Internal radius, norad - Without radius, add - Advertisement, mac - MAC auth, sms - SMS OTP) (e.g., norad) RW
   1.4 General.ExternalLandingPage - Enable external landing page (e.g., 1) RW
   1.5 General.LandingPageAddress - External landing page address (e.g., www.landingpageaddr.com) RW
   1.6 General.HTTPSRedirect - Enable HTTPS redirect RW
 2. Radius
   2.1 Radius.Server1 - First radius server address RW
   2.2 Radius.Server2 - Second Radius server address RW
   2.3 Radius.AuthenticationPort - Authentication port RW
   2.4 Radius.AccountingPort - Accounting port RW
   2.5 Radius.RadiusSecretKey - Radius secret key RW
   2.6 Radius.UAMPort - UAM port RW
   2.7 Radius.UAMUIPort - UAM UI port RW
   2.8 Radius.UAMSecret - UAM secret RW
   2.9 Radius.NASIdentifier - NAS identifier RW
   2.10 Radius.SwapOctets - Swap octets RW
   3.1 Radius.LocationName - Location name RW

Management Server Information:

 1. ManagementServer.URL - Server url (e.g., http://192.168.1.110:8080/openacs/acs) RW
 2. ManagementServer.Username - Username (e.g., easycwmp) RW
 3. ManagementServer.Password - Password (e.g., easycwmp) RW
 4. ManagementServer.PeriodicInformEnable - Enable periodic inform (e.g., 1 or 0) RW
 5. ManagementServer.PeriodicInformInterval - Interval (e.g, 100) RW
 6. ManagementServer.PeriodicInformTime - Inform time (e.g, 0001-01-01T00:00:00Z) RW