Line 29: |
Line 29: |
| <tr> | | <tr> |
| <td>LLDP frame filter</td> | | <td>LLDP frame filter</td> |
− | <td><span style="color:red">off</span> {{!}} on; default: <b>off</b></td> | + | <td>off {{!}} on; default: <b>off</b></td> |
| <td>Enable to stop the forwarding of LLDP frames.</td> | | <td>Enable to stop the forwarding of LLDP frames.</td> |
| </tr> | | </tr> |
Line 42: |
Line 42: |
| The figure below is an example of the '''All Ports''' window, color indicates port speed and status: | | The figure below is an example of the '''All Ports''' window, color indicates port speed and status: |
| | | |
− | [[File:Networking_tswos_manual_ports_ports_settings_port_settings.png|border|class=tlt-border]] | + | [[File:Networking_tswos_manual_ports_ports_settings_port_settings_{{{poe}}}.png|border|class=tlt-border]] |
| | | |
| To change port settings select port and press `edit (number of ports) ports` button: | | To change port settings select port and press `edit (number of ports) ports` button: |
| | | |
− | [[File:Networking_tswos_manual_ports_ports_settings_port_settings_edit.png|border|class=tlt-border]] | + | [[File:Networking_tswos_manual_ports_ports_settings_port_settings_edit_{{{poe}}}.png|border|class=tlt-border]] |
| | | |
| You will be redirected to `Port settings`. From here you can enable/disable ports or change settings: | | You will be redirected to `Port settings`. From here you can enable/disable ports or change settings: |
| | | |
− | [[File:Networking_tswos_manual_ports_ports_settings_port_settings_settings.png|border|class=tlt-border]] | + | [[File:Networking_tswos_manual_ports_ports_settings_port_settings_settings_{{{poe}}}.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 164: |
Line 164: |
| [[File:Networking_tswos_manual_ports_port_mirroring_edit.png|border|class=tlt-border]] | | [[File:Networking_tswos_manual_ports_port_mirroring_edit.png|border|class=tlt-border]] |
| | | |
− | You will be redirected to `Port mirroring settings`. From here you can select ingress and egress ports: | + | You will be redirected to `Port mirroring settings`, from here you can select ingress and egress ports: |
| | | |
| [[File:Networking_tswos_manual_ports_port_mirroring_configuration.png|border|class=tlt-border]] | | [[File:Networking_tswos_manual_ports_port_mirroring_configuration.png|border|class=tlt-border]] |
Line 226: |
Line 226: |
| <li><b>STP:</b> STP must be disabled in Network -> Spanning Tree and loopback detection must be enabled for the service to function.</li> | | <li><b>STP:</b> STP must be disabled in Network -> Spanning Tree and loopback detection must be enabled for the service to function.</li> |
| <li><b>Port unblocking:</b> When a loop occurs before a broadcast, it won't be recognized until the broadcast transmits its own packets, since the service only listens for packets with its own particular protocol.</li> | | <li><b>Port unblocking:</b> When a loop occurs before a broadcast, it won't be recognized until the broadcast transmits its own packets, since the service only listens for packets with its own particular protocol.</li> |
| + | |
| + | [[File:Networking_tswos_manual_ports_loopback_detection_port_tracking.png|border|class=tlt-border]] |
| + | |
| + | To change port tracking setting press on port and you will be redirected to `Port tracking configuration`: |
| + | |
| + | [[File:Networking_tswos_manual_ports_loopback_detection_port_tracking_configuration.png|border|class=tlt-border]] |
| + | |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Enable</td> |
| + | <td>off {{!}} on; default: <b>on</b></td> |
| + | <td>Enable port tracking.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Recovery mode</td> |
| + | <td>Auto {{!}} Manual; default: <b>Auto</b></td> |
| + | <td>Manages port unblocking type.Possible modes: |
| + | <li>Manual: Port is blocked until manual unblock.</li> |
| + | <li>Auto: Unblocked automatically depending on the global Auto-recovery interval value.</li> |
| + | </td> |
| + | </tr> |
| + | </table> |
| + | |
| + | ==Port Security== |
| + | |
| + | This section displays information about the status of the device's ports with the ability to configure port security settings. |
| + | |
| + | ===General=== |
| + | ====Port Settings==== |
| + | ---- |
| + | The figure below is an example of the '''Port Settings''' window, color indicates port speed and status: |
| + | |
| + | [[File:Networking_tswos_manual_ports_port_security_port_settings_{{{poe}}}.png|border|class=tlt-border]] |
| + | |
| + | To change port security settings select port and press `edit (number of ports) ports` button: |
| + | |
| + | [[File:Networking_tswos_manual_ports_port_security_port_settings_edit_{{{poe}}}.png|border|class=tlt-border]] |
| + | |
| + | You will be redirected to `Port security settings`. From here you can enable/disable ports or change security settings: |
| + | |
| + | [[File:Networking_tswos_manual_ports_port_security_port_settings_settings_{{{poe}}}.png|border|class=tlt-border]] |
| + | |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Enable</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Enable security for port.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Radius sever</td> |
| + | <td>radius server ID; default: <b>example</b></td> |
| + | <td>Radius server ID.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Radius unreachable action</td> |
| + | <td>Accept {{!}} Reject; default: <b>Accept</b></td> |
| + | <td>"Accept" gives anyone access to the port when the radius server is unreachable. "Reject" only unblocks the port if radius server explicitly authorizes it.</td> |
| + | </tr> |
| + | </table> |
| + | |
| + | ===Port Status=== |
| + | ---- |
| + | This section displays port status information. There is also an option to select, enable ports security, choose RADIUS server and change RADIUS unreachable action: |
| + | |
| + | [[File:Networking_tswos_manual_ports_port_security_port_status.png|border|class=tlt-border]] |
| + | |
| + | <table class="nd-othertables_2"> |
| + | <tr> |
| + | <th width="250">Field Name</th> |
| + | <th width="900">Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Port</td> |
| + | <td>Port ID.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Enabled</td> |
| + | <td>Enables port security on this port.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Status</td> |
| + | <td>Port status.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Radius server</td> |
| + | <td>Authenticates and authorizes devices trying to connect to this port.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Radius unreachable action</td> |
| + | <td>"Accept" gives anyone access to the port when the radius server is unreachable. "Reject" only unblocks the port if radius server explicitly authorizes it.</td> |
| + | </tr> |
| + | </table> |
| | | |
| | | |
| [[Category:{{{name}}} Network section]] | | [[Category:{{{name}}} Network section]] |