Line 97: |
Line 97: |
| | | |
| Devices with eSIM support enable features like "Sim switch" for single SIM slot devices and more "Failover" capabilities. | | Devices with eSIM support enable features like "Sim switch" for single SIM slot devices and more "Failover" capabilities. |
| + | |
| + | ===SIM Switch=== |
| + | ---- |
| + | The <b>SIM Switch</b> section in <b>Network → Mobile</b> page provides you with the possibility to configure SIM switching rules, i.e., set up circumstances under which the device will perform a switch from using one SIM card to another. Refer to the figure and table below for information. |
| + | |
| + | [[File:Networking_rutos_manual_mobile_sim_esim_switch.png|border|class=tlt-border]] |
| + | |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Enable automatic switching</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Turns automatic SIM switching on or off.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Check interval</td> |
| + | <td>integer [3..3600]; default: <b>30</b></td> |
| + | <td>The frequency (in seconds) at which the device will check for SIM switch conditions. If such a condition exists, the router will perform a SIM switch, if not - it will check for the same conditions again after the amount of time specified in this field passes.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Attempts before SIM switch</td> |
| + | <td>integer [1..10]; default: <b>3</b></td> |
| + | <td>How many times a condition will be checked before executing a SIM switch. For example, if the device is a state that meets at least one SIM switch condition, the device will perform a number of additional checks specified in this field and will perform a SIM switch only if the condition is met on every check.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>On weak signal<span style="color:red">*</span></td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when the signal strength drops below a certain threshold.</td> |
| + | </tr> |
| + | <tr> |
| + | <td><span style="color:red">*Signal strength (dBm)</span></td> |
| + | <td>integer [-120..-50]; default: <b>-90</b></td> |
| + | <td>Lowest signal's strength value (RSSI) in dBm below which a SIM card switch should occur. More information: [[RSSI|RSSI]]</td> |
| + | </tr> |
| + | <tr> |
| + | <td>On data limit</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when the mobile data limit for this SIM card is reached. You can set up a mobile data limit in the Network → [[{{{name}}} WAN|WAN]] (Basic WebUI mode) or Network → [[{{{name}}} Interfaces|Interfaces]] (Advanced WebUI mode) pages by clicking 'Edit' next to the interface you wish limit the data for.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>On SMS limit</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when the SMS limit for this SIM card is reached. You can set up SMS limit in the Network → Mobile → [[#General|General]] page.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>On roaming</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when roaming conditions are detected.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>No network</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when a network connection is not available.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>On network denied</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when access to a network is denied by an operator.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>On data connection fail</td> |
| + | <td>off {{!}} on; default: <b>off</b></td> |
| + | <td>Performs a SIM switch when mobile data connection fails. Possible failure determination methods are: |
| + | <ul> |
| + | <li><b>LCP echo</b></li> |
| + | <li><b>ICMP echo</b></li> |
| + | </ul>If no echo is received, the data connection is considered to be down. |
| + | </td> |
| + | </tr> |
| + | </table> |
| + | |
| + | When configuring SIM switching from the Secondary card, an additional field called "Switch back to primary SIM card after timeout" becomes available: |
| + | |
| + | [[File:Networking_rutos_manual_mobile_sim_management_sim_switching_rules_back_to_primary.png|border|class=tlt-border]] |
| + | |
| + | <table class="nd-mantable"> |
| + | <tr> |
| + | <th>Field</th> |
| + | <th>Value</th> |
| + | <th>Description</th> |
| + | </tr> |
| + | <tr> |
| + | <td>Switch back to primary SIM card after timeout</td> |
| + | <td>yes {{!}} no; default: <b>no</b></td> |
| + | <td>Attempts to switch back to the primary SIM card once the specified period of time passed.</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Initial timeout (min)</td> |
| + | <td>integer; default: <b>1</b></td> |
| + | <td>Indicates a time value (in minutes) after which the device will attempt to switch back to the primary SIM card.</td> |
| + | </tr> |
| + | </table> |