Template:Networking rut9xx firmware change log

From Teltonika Networks Wiki
Revision as of 13:09, 16 December 2022 by Dziugas (talk | contribs)

RUT9_R_00.07.02.7 | 2022.09.12

  • Improvements:
    • Improved manual-auto connection mode
  • Fixes
    • Fixed AT command for SMS storage usage
    • Fixed CVE-2022-1012 memory leak vulnerability
    • Fixed CVE-2022-37434 kernel vulnerability
    • Fixed GPS constellation settings
    • Fixed interface option reset after VLAN ID change
    • Removed memory leak on port events
    • Fixed WiFi Scanner out of range crash when iterating collected data

RUT9_R_00.07.02.6 | 2022.08.24

  • Improvements:
    • Added 'home.vodafone.de' APN
    • Improved stability of device information storage
  • Fixes:
    • Added SMSC type omitting when empty SMSC number parsed in SMS PDU mode
    • Fixed Serial-symlink dmesg messages
    • Fixed VoLTE management
    • Fixed OpenVPN tls-auth and tls-crypt option names

RUT9_R_00.07.02.5 | 2022.08.12

  • Improvements:
    • Updated curl to version 7.83.1
    • Updated firmware validation error messages
    • Added multiple source IP address support to the Port Forwards page
    • Increased custom APN Username & Password field maximum length to 64 symbols
    • Added auto switch to modem's SMS storage when SIM card storage doesn't exist
    • Improved mobile connection status handling
    • Added CSP headers Hotspot WebUI landing page
  • Fixes:
    • Fixed CVE-2022-32205, CVE-2022-32206, CVE-2022-32207, CVE-2022-32208 curl vulnerabilities
    • Fixed CVE-2022-30065 busybox vulnerability
    • Fixed file upload path traversal
    • Removed Data to Server limit to proccess less than 10 instances
    • Fixed Data to Server 'out of memory' crashes when database is full or has a large amount of data
    • Fixed OpenVPN dev setting logic
    • Fixed OpenVPN updating from legacy issue that caused IPv6 not to work
    • Fixed MAC and leasetime setting for Bridge & Passthrough modes
    • Fixed modal tabs navigation when editing wireless interface with non-english languages

RUT9_R_00.07.02.4 | 2022.07.20

  • Improvements:
    • Added default password change warning message before firmware downgrade
    • Extended time period for device to make connection to operator
    • Reduced the number of modem reboots when changing mobile settings
    • Reduced excessive log output when no SIM card is inserted
    • Added modem restart prevention on modem init
    • Added disable RPLMN option in the SIM section of the SIM card config
  • Fixes:
    • Fixed CVE-2022-2068 vulnerability
    • Disabled autoconnect on stop-network call
    • Fixed Hotspot login via landing page issue

RUT9_R_00.07.02.3 | 2022.06.27

  • New Features:
    • Port Mirroring
  • Improvements:
    • Added ping to DNS IPv6 support
    • Added modem reset to default state after device FW upgrade
    • Modem init now checks NVRAM sensitive commands before setting
    • GSM output was made consistent
    • Updated FSTools package to version 2022-05-03
    • Added security headers to web requests
    • Added default VoLTE value
    • Specified IP address family on operator control's ping to DNS feature
  • Fixes:
    • Fixed CVE-2019-12900 libbz2 vulnerability
    • Fixed behavior of some gsmctl commands
    • Fixed CVE-2022-23303 hostapd vulnerability
    • Fixed CVE-2022-29581 Linux kernel vulnerability
    • Fixed CVE-2022-29458 ncurses vulnerability
    • Fixed CVE-2022-1292 c_rehash script command injection vulnerability
    • Fixed band locking issue
    • Fixed race condition for wireless configuration initialization

RUT9_R_00.07.02.1 | 2022.06.06

  • Improvements:
    • Improved GSM related messages in Troubleshoot logs
  • Fixes:
    • Fixed IGMP Proxy menu item not appearing after package installation
    • Fixed default mobile network configuration generation
    • Fixed MODBUS write requests and Mobile Utils option setting

RUT9_R_00.07.02 | 2022.05.23

  • New features
    • Overview side widget
    • IGMP Proxy
    • Privileged Access Management (PAM)
    • AWS Greengrass support
    • HTTPS certificate and key upload feature
    • SSH public keys edit box
    • License page
    • DNP3 data for Data to Server
  • Improvements
    • Updated busybox to version: 1.34.1
    • Updated curl to version 7.79.1
    • Added iptables filter package for string filtering
    • Added CHAP authentication for L2TP VPN
    • Added IPv6 support for L2TPv3 VPN
    • Added EAP-MSCHAPV2 authentication method for IPsec VPN
    • Added IPv6 support to Auto Reboot
    • Added 'Save to flash' and 'Test configuration' button to DNP3 configuration page
    • Updated SNMP version 5.9.1
    • Added OpenSSL authentication options to SNMPv3
    • Added support for OSPF redistribution options and OSPF neighbors
    • Added password field to BGP Peers page
    • Extended BGP "AS" field validation to accept integers up to 4294967295
    • Added "DHE+RSA" to OpenVPN cipher selections
    • Increased OpenVPN max password length from 128 bytes to 512 bytes
    • Made HMAC key direction initial value dependent on the role of the instance (client or server)
    • Made HMAC key and HMAC authentication key upload fields required
    • Added DES to IPsec encryption algorithms selections
    • Added special character support for CHAP secrets
    • Added validation requirements for PPTP user list username field
    • Added option to manually enter Public key in Wireguard configuration
    • Made generating Wireguard keys possible only while in auto mode
    • Added Events Log database to troubleshoot archive
    • Added RFC1918 filter field
    • Added the possibility to unblock multiple blocked devices at once
    • Added 'Port' column to blocked login attempts table
    • Added Speedtest server refresh
    • Updated Speedtest server list
    • Added asterisk option to Site Blocking
    • Added MD5 and SHA256 checksums to package validation page
    • Changed certificate requirements to only require client key file if client certificate is used
    • Added pagination and data retention between table pages
    • Added pagination functionality to tables when there are more than 10 records
    • Improved table sorting by saving user provided sort settings in the browser
    • Improved drag and drop functionality
    • Added the possibility to drag and drop files onto upload components
    • Moved 'Root CA' from the 'Access Control' page to the 'Certificates' page
    • Added 'Strict-Transport-Security' response header for HTTPS
    • Added 'breadcrumbs' to modal windows
    • Improved initial WebUI loading after login
    • Added mobile bytes sent and bytes received SNMP OIDs
    • Added mobile LED turn off feature ('System -> Administration' page)
    • Added 'iot.1nce.net', 'internet', 'VZWINTERNET' and Truphone APNs to APN database
    • Updated mobile usage data point calculation logic
    • Added the possibility to manually enter operator number
    • Improved obtain mobile cell ID process
    • Added modem restart if SIM card is removed during APN database fetching process
    • Added unauthorized call logging
    • Added space character support in SMS commands
    • Disabled SMS modem storage configuration form when SIM is not inserted
    • Changed SMS '%wi' parameter value to return IP address of any currently used WAN interface (not only wired)
    • Added external modem SMS limit Overview card and widget
    • Made in-use APNs visible next to mobile interface configurations (before clicking the 'Edit' button)
    • Added duplicate value check for list configuration options
    • Changed mobile card instance design
    • Fixed 'Mobile Data usage reset' SMS rule
    • Fixed the default state parameter of SMS list POST/GET command
    • Added Hotspot configuration profiles
    • Added local Hotspot user password hashing
    • Added Hotspot password encoding option
    • Improved Hotspot related firewall rule setting
    • Improved WiFi Scanner enable switch to toggle 2 and 5 GHz instances separately
    • Removed CHAP authentication protocol for WiFi Hotspots due to incompatibility with hashed passwords
    • Added ubus support to Hotspot
    • Changed default port name of WiFi devices for 'Topology state' Events Reporting rule
    • Added AVL "Static Navigation" flag
    • Added GSV parsing for NMEA collecting
    • Added newline and GPS location actions to I/O Juggler
    • Added error code 5 for reserved SAMBA user names
    • Added Mobile data and SMS limit features for external modem
    • Added I/O SNMP trap
    • Added ISO 8601 time format to I/O Juggler's '%ts' parameter
    • Added device name parameter '%pc' to I/O Juggler
    • Added ACL or ADC SNMP trap notification on enter/exit/both
    • Added ACL MQTT topic
    • Added PPPoE VLAN priority support
    • Made VRRP ping section dependent on main instance
    • Added 'WAN to LAN' switch
    • Added CRC verification support to MODBUS and RS232/RS485
  • Fixes
    • Fixed CVE-2021-20322, CVE-2021-4197, CVE-2022-1011, CVE-2022-0847 kernel vulnerabilities
    • Fixed CVE-2022-28391 busybox vulnerability
    • Fixed CVE-2018-16789 shellinabox vulnerability
    • Fixed CVE-2021-44543, CVE-2021-44542 privoxy vulnerabilities
    • Fixed CVE-2021-43618 GNU Multiple Precision Arithmetic Library vulnerability
    • Fixed zlib backport security issue
    • Fixed Wireguard firewall zone assignment
    • Fixed queued packages disappearing from list after FW upgrade with keep settings
    • Fixed error message display for multiple input validation rules
    • Fixed incorrect DHCP validation range for start and limit fields
    • Removed 'Bring up on boot' option from network interface configuration pages
    • Fixed coma-separated DHCP options disappearing after save
    • Fixed exclude and listen interfaces
    • Fixed 'Use broadcast flag' option saving
    • Fixed firewall zone assignment when creating new interfaces
    • Fixed OpenVPN 'Netmask' and 'IP address' field validations
    • Fixed OpenVPN TAP configuration saving issue
    • Fixed OpenVPN switching to TUN mode when uploading a configuration from file
    • Fixed dynamic BGP route state display
    • Fixed BGP peer enable in edit page
    • Fixed issue when no L2TP client instance could be bound to IPsec
    • Fixed firewall rule and zone behavior related to config section creation
    • Added default value for L2TPv3 netmask, which is now written to config after save
    • Fixed passthrough option saving to IPsec file
    • Fixed DMVPN issue where instance configuration could not be saved
    • Fixed Wireguard peer could not be saved issue
    • Fixed NTP client time synchronization after factory reset
    • Fixed device time display with selected time zone
    • Fixed MODBUS TCP indexation missing bracket issue
    • Fixed initial MODBUS TCP request count validation
    • Fixed PIN 3/4 direction switching over MODBUS TCP
    • Fixed MODBUS data to MQTT socket closing issue when connection fails
    • Fixed MODBUS alarm configuration deletion
    • Fixed DNP3 master not working after FW upgrade with 'keep settings'
    • Fixed DNP outstation not returning error messages
    • Added missing SNMP objects: mobile IP, data sent/received today
    • Fixed MQTT Publisher 'Remote address' field validation
    • Fixed long interface name support for Azure IoT Hub
    • Increased maximum Azure IoT Hub 'Connection String' length to 4096 characters
    • Fixed missing sent/received data issue
    • Fixed URL input field length validation
    • Fixed admin login issue after upload of backup from a device with older firmware versions
    • Fixed MAC address formatting in Events reporting messages
    • Fixed Events reporting DHCP lease message spam, when no new lease is added
    • Fixed logging crashing after downloading Troubleshoot file
    • Made Wake on LAN visible only on devices with Ethernet ports
    • Fixed Traffic log file transfer to FTP server
    • Fixed Web Filter service reloading after a host list file is uploaded
    • Fixed access denied messages when sending JSON-RPC requests from root user
    • Fixed error message display about duplicated intervals in Profile scheduler
    • Fixed FW upgrade with 'keep settings' migration issue for Access Control's 'Fail count' and 'Device port' fields
    • Corrected OSPF Routing card values, value positions and names
    • Fixed global secret instances not being removed when there are no IPsec instances
    • Fixed uploaded file remove icon not staying in position on hover
    • Fixed Overview card collapse issue that made it unresponsive after too many clicks
    • Removed WAN6 interface from the Overview page
    • Fixed mobile IPv6 display in Events Reporting status messages
    • Fixed Bridge mode when DNS2 is not available
    • Fixed PAP/CHAP username and password fields not saving in interface edit window
    • Fixed sending email without secure connection for providers that support such an option
    • Fixed 'N/A' parameter showing up in SMS Utilities monitoring status message
    • Fixed Call Utilities Events Log message for reboot rule
    • Fixed SMS command validation for no-authorization option
    • Fixed MODBUS SMS alarms 'Enable' option saving
    • Fixed running RMS with no SIM card inserted issue
    • Fixed firmware available on server version checking issue
    • Fixed CVE-2020-15078 openvpn vulnerability
    • Fixed storage calculation for packages
    • SMS Utilities: enhanced service security
    • Fixed firmware deletion after leaving the page
    • Fixed setup wizard redirect after LAN IP change
    • Fixed various validation bugs, typos, option hints & alignments
    • Fixed multiple IPv6 configuration field validations
    • Fixed unnecessary SIM switch issue when Multi-APN is configured
    • Fixed MODBUS TCP slave modem not starting after switching SIM cards
    • Fixed PDP logging for Verizon operator
    • Added multiwan support for Wireguard default route
    • Fixed wireless signal strength display when no clients are connected
    • Fixed loss of connectivity for clients when router is in STA+AP mode
    • Added validation that prevents automatic connection to first unencrypted WiFi AP when using MULTI AP
    • Fixed Wifi Scanner data not being stored in certain scenarios
    • Fixed WiFi scanner not turning on after FW upgrade with 'keep settings'
    • Fixed Hotspot user group limit not resetting on specified time
    • Removed an RMS error message when no Hotspot users were created
    • Fixed Hotspot landing page image upload issue
    • Fixed restoring GPS HTTPS options after FW upgrade with 'keep settings'
    • Fixed missing NMEA sentences
    • Fixed NMEA cache sentence calculation
    • Fixed 'outside/inside range' condition for AVL I/O Analog input trigger
    • Fixed I/O Juggler external modem recognition
    • Fixed flash driver reformatting after memory shrink
    • Fixed DLNA package installation issue
    • Changed Media Directories field to be required
    • Fixed SAMBA fields value display
    • Fixed relay output value display in I/O Juggler condition page
    • Fixed I/O Juggler's WiFi rule not enabling or disabling WiFi interfaces
    • Fixed I/O Juggler's double delete issue on I/O Juggler action and condition instances
    • Fixed I/O Juggler's incorrect I/O status messages
    • Fixed APN migration if APN was selected from APN list on legacy firmware
    • Fixed RIP configuration migration from legacy firmware versions
    • Fixed Wireguard interface status setting migration from legacy firmware versions
    • Fixed default config options for SSH and Web access SMS Utilities rules
    • Fixed POST/GET SMS listing by state
    • Fixed automatic port open after RS232/RS485 Over IP server & bidirect configuration changes
    • Fixed 'iostatus' SMS rule

RUT9_R_00.07.01.4 | 2022.02.25

  • Improvements
    • Increased Port Forwards rule max name length
    • Added a new '%it' parameter for UTC time in ISO 8601 format to I/O Juggler
    • Improved RS232 Port and Timeout validation
  • Fixes
    • Added missing bracket to the end of MODBUS messages
    • Fixed preserving the contents of /etc/luci-uploads/ after FW upgrade with the 'Keep all settings' option
    • Fixed IPv4-Gateway column showing empty values in the Status -> Routes page
    • Fixed firewall extra option validation
    • Fixed Hotspot enable button validation
    • Removed invalid network interface selections from the "Network" dropdown in the Wireless interface configuration page
    • Fixed 3G led animation issue
    • Fixed Hotspot 2.0 status display in the System -> Status page
    • Changed the logic of uploading files to the modem
    • Fixed usage of custom headers in I/O Juggler HTTP action
    • Fixed 'verify' option parsing for I/O Juggler
    • Fixed OpenVPN server configuration with password authentication
    • Fixed NTP interval length validation
    • Fixed network interface enable after Drag & Drop
    • Updated NTP client interval to 24h
    • Fixed connection to whitelist carriers
    • Fixed Passthrough mode when DHCP is disabled
    • Fixed 'Deny data roaming' feature
    • Fixed mobile blocking dependency on region
    • Disabled Ping To DNS functionality when Bridge/Passthrough mode is enabled

RUT9_R_00.07.01.2 | 2022.01.04

  • New features
    • DFOTA modem upgrade system for Quectel modems
  • Improvements
    • Removed L2TP section title prefixes
    • Added necessary/forced module firmware updates to handle AT&T network update
  • Fixes
    • Fixed IPSec crashing issue using mobile
    • Fixed FW flashing when chip is in unknown state
    • Fixed CPU usage percentage display in the Overview page
    • Fixed FOTA timeout issue when server does not respond
    • Fixed installation of backup packages
    • Fixed mobile data limit display after profile change
    • Fixed Bridge mode without multi-APN
    • Fixed multi mobile interface checking
    • Fixed error handling when the modem is not responding
    • Prolonged autoconnect setting timeout

RUT9_R_00.07.01.1 | 2021.11.22

Note: Firmware version RUT9_R_00.07.01.1 released on 2021.11.22 was removed due to an issue with IPsec tunnel while using mobile connection.

  • Fixes
    • Fixed image signature addition

RUT9_R_00.07.01 | 2021.11.18

Note: Firmware version RUT9_R_00.07.01 released on 2021.11.18 was removed due to an issue with keep settings functionality.

  • New features
    • Load Balancing Rules
    • 802.11s based wireless mesh network support
    • Multiple Wireless AP feature
    • Tinc VPN
    • German language support
    • Manual-Auto operator select
  • Improvements
    • Improved WebUI functionality when multiple browser tabs are open
    • Updated base to OpenWrt version 21.02
    • Updated kernel to version 5.4.141
    • Updated mtd-utils to version 2.1.2
    • Updated busybox to version 1.33.1
    • Updated ubus to version 2021-06-3
    • Updated ubox to version 2020-10-25
    • Updated rpcd to version 2021-03-11
    • Updated opkg to version 2021-06-13
    • Updated fstools to version 2021-01-04
    • Updated wwan to version 2019-04-29
    • Updated ethtool to version 5.10
    • Updated uhttpd to version 2021-03-21
    • Updated ppp to version 2020-10-03
    • Updated odhcpd to version 2021-07-18
    • Updated hostapd to version 2020-06-08
    • Updated dropbear to version 2020.81
    • Updated dnsmasq to version 2.85
    • Updated netifd to version 2021-07-26
    • Updated firewall3 to version 2021-03-23
    • Updated libjson-c to version 0.15
    • Updated libevent2 to version 2.1.12
    • Updated mac80211 to version 5.10.42-1
    • Updated wireless-regdb to version 2021.04.21
    • Updated binutils to version 2.35.1
    • Updated gdb to version 10.1
    • Updated strace to version 5.10
    • Updated trace-cmd to version 2.9.1
    • Updated valgrind to version 3.16.1
    • Updated ath10k-ct-firmware to version 2020-11-08
    • Updated procd to version 2021-02-23
    • Updated iw to version 5.9.8
    • Updated iproute2 to version 5.11.0
    • Updated iptables to version 1.8.7
    • Updated nettle to version 3.6
    • Updated libpcap to version 1.9.1 rel3
    • Updated elfutils to version 0.180
    • Updated cryptodev-linux to version 1.11
    • Updated linux-firmware to version 20201118
    • Updated util-linux to version 2.36.1
    • Updated openwrt-keyring to version 2021-02-20
    • Updated mtd to version rel26
    • Updated fwtool to version 2019-11-12
    • Updated ca-certificates to version 20210119
    • Updated wireguard-tools to version 1.0.20210223
    • Updated iwinfo to version 2021-04-30
    • Updated ipset to version 7.6
    • Updated gre to version rel12
    • Updated wolfssl to version 4.7.0
    • Updated ustream-ssl to version 2020-12-10
    • Updated uclient to version 2021-05-14
    • Updated readline to version 8.1
    • Updated mbedtls to version 2.16.11
    • Updated libusb to version 1.0.24
    • Updated libunwind to version 1.5.0
    • Updated libubox to version 2021-05-16
    • Updated libnl-tiny to version 2020-08-05
    • Updated libnftnl to version 1.1.8
    • Updated libiconf-full to version 1.16
    • Updated libbsd to version 0.10.0
    • Updated gmp to version 6.2.1
    • Updated ulogd to version rel6
    • Updated sqm-scripts to version 1.5.0
    • Updated ntpclient to version rel14
    • Updated nmap to version 7.80
    • Updated curl to version 7.77.0
    • Updated zerotier to version 1.6.5
    • Updated xtables-addons to version 3.13
    • Updated xl2tpd to version 1.3.16
    • Updated stunnel to version 5.59
    • Updated strongswan to version 1.0.13
    • Updated sstp-client to version 1.0.13
    • Updated pptpd to version rel5
    • Updated openvpn to version 2.5.3 rel2
    • Updated ntpd to version rel3
    • Updated net-snmp to version rel2
    • Updated mosquitto to version 2.0.11
    • Updated miniupnpd to version 2.2.1 rel 3
    • Updated etherwake to version rel5
    • Updated libzip to version 1.7.3
    • Updated libgpg-error to version 1.39
    • Updated glib2 to version 2.66.4
    • Updated libnetfilter-conntrack to version 1.0.8
    • Updated libnetfilter-log to version rel3
    • Updated lzo to version rel4
    • Updated nghttp2 to version 1.43.0
    • Updated openvpn-easy-rsa to version 3.0.8 rel3
    • Updated iperf to version rel2
    • Updated iperf3 to version 3.10.1
    • Updated e2fsprogs to version 1.45.6
    • Updated fuse to version 2.9.9
    • Updated udprelay to version 2020-02-26
    • Updated qmicli to version 1.28.2
    • Updated pcre to version 8.45
    • Updated libsmpp34 to version 1.14.1
    • Updated libiwinfo to version 2.1
    • Added netifd library for additional information related to network interfaces
    • Updated openssl to version 1.1.1l
    • Updated privoxy to version 3.0.32
    • Added ACL reload method for sessions
    • Added 'Advertisement interval' field to the VRRP configuration window
    • Added a PPTP-to-WAN Zone Forwarding rule when default route is enabled on PPTP client
    • Added email user group validation for sendind test emails with Events reporting
    • Added an event logging feature for Ping Reboot events
    • Improved file/section deletion logic: now files are also deleted after deleting a related config section
    • Improved package deletion logic
    • Added the possibility to configure multiple reboot times in one Reboot Scheduler configuration instance
    • Updated 'External system log server' field validation to accept IPv6 addresses
    • Added redirect to Overview page after login
    • Added WebUI session timeout after user inactivity
    • Added placeholder text to dropdown menus
    • Improved multi-select design and functionality
    • Added Unix timestamp, local ISO time, UTC time to Modbus
    • Added info message when selected file cannot be uploaded
    • Improved IPsec throughtput
    • Added IPSec "Compatibility mode" configuration support
    • Made SNMP 'Community name' option editable
    • Added the option to delete configurations to the SMS Utilities 'UCI' rule
    • Added 'hour', 'week day', 'month day' slelection options to SMS Limit configuration
    • Added Lithuanian and Verizon APNs
    • Added modem selection for the 'Send SMS' option in Auto Reboot settings
    • Added the possibility to get total data usage value without specifying time interval via ubus
    • Added return SIM count command
    • Added new configuration options to the Failover feature
    • Changed Failover page availability from Advanced only both advanced and basic
    • Made Failover Interfaces table rows draggable when in 'Load Balancing' mode
    • Changed Failover page 'Ratio' fields to a smaller size
    • Added the possibility to allow multiple Hotspot users to log in with the same SMS OTP
    • Added 'Duplicate passwords are not allowed' error message to Hotspot landing pages
    • Added 'Allow password duplicates' field to the Hotspot configuration page
    • Improved wireless frequency option layout
    • Added an indication to the GPS map when GPS service is disabled
    • Added external modem support for the 'Mobile Usage' graph
    • Added check to refuse firmware lower than 7.0 on devices with Micron flash
    • Added I/O support to SNMP
    • Removed ubus list method due to security reasons
    • Added MODBUS "%I, %T, %S, %r, %n" support to MODBUS Data Sender
    • Removed search engine site crawling
    • Improved IPSec "Local/Remote source" validation
    • Added Firewall "all" and "custom" protocol options
    • Added Backup file size limit of 2 MB
    • Improved basic/advanced mode changing
    • Improved Wireguard "IP Addresses" field validation
    • Added language download support from language selection section
    • Added PPTP "Client to client" configuration support
    • Made DDNS "username", "password", "host" fields optional
    • Added SSTP "Default route" configuration support
    • Added SMS Limit hour, week day and month day support
    • Added Passthrough "Leasetime" and "Unit" configuration support
    • Added Call Utilities "Active Timeout" configuration support
    • Added support for PL2303GC serial to USB chip
    • Added bgscan feature to wpa_supplicant
    • Optimized Wireless device status information requests in all WebUI pages
    • Added "Topology state" support to Events Reporting
    • Added GPS AVL "Don't Contain Connection" and "Retry on Fail" configuration support
  • Fixes
    • Made RMS 'Connect' button disabled when a connection attempt is already in progress
    • Added validation for TLS Clients 'Private network' option
    • Fixed the validation range for MTU fields
    • Fixed removing firmware image file after leaving the fimware upgrade page
    • Fixed network selection list for Traffic Logging - added all available LAN networks
    • Fixed DHCP Options validation
    • Fixed configuration profile date display
    • Fixed blank page after invalid URL in login page
    • Fixed TR-069 related firewall rule loading
    • Fixed remote subnet netmask validation issues for the GRE Tunnel configuration
    • Fixed WebUI section toggle
    • Fixed package installation modal layout
    • Fixed current page values showing up in login page username field
    • Fixed the possibility to create section with a name that is already in use in the same config file
    • Fixed OpenVPN username and password deletion when deleting configuration instance
    • Fixed session closing issue for the user whose password was just changed
    • Updated MODBUS credential validation
    • Updated MQTT credential validation
    • Fixed DNS 'Rebind protection' setting when switch is disabled
    • Updated libgcrypt to version 1.9.3 to fix CVE-2021-33560
    • Fixed CVE-2021-33624, CVE-2021-29648 vulnerabilities
    • Fixed DHCP 'Lease time' and 'Unit' option saving over the Setup Wizard LAN page
    • Fixed Reboot Scheduler not removing crontab file after disabling the rule
    • Fixed OpenVPN 'Extra options' field validation to allow a space character
    • Added table drag and drop functionality to the Firewall's Traffic Rules page
    • Fixed DNP3 Outstation crash caused by non-void function returning no value
    • Fixed RMS 'Copy' button functionality
    • Fixed gsmd deamon crashing after modem restart
    • Fixed gsm memory leak
    • Fixed WCDMA band names for MEIG modules
    • Fixed SMS Gateway loading screen issue when sending an SMS message
    • Fixed mobile data database error after upgrading firmware with the 'Keep settings' option
    • Fixed rpcd memory leak issue
    • Fixed network information gathering
    • Fixed 3G LED not being active in 3G mode
    • Fixed data limit accuracy issue
    • Fixed SIM Switch back to default SIM crash loop when SIM1 is disabled
    • Removed unused SIM Switch struct objects
    • Fixed incorrect loading after saving Failover configuration
    • Fixed escaping '#' symbol from hotspot username and password fields
    • Fixed NTP GPS Synchronization swith to enable GPS service
    • Fixed MODBUS Serial Master crash when requesting a 4-byte datatype from a 2-byte data payload
    • Added a check if DNP3 is installed for 'Serial type' option
    • Fixed Storage Memory Expansion issues related to upgrading from version 6.X with the 'Keep settings' option
    • Patched CVE-2021-40528 vulnerability
    • Patched CVE-2021-40490 vulnerability
    • Patched CVE-2020-16120 vulnerability
    • Fixed VLAN section creation
    • Returned Interfaces "Port priority" option
    • Fixed missing Content-Type header to initial WebUI response
    • Fixed RIP information parsing in status page
    • Fixed OpenVPN IPv6 netmask validation
    • Fixed SNMP Trap Settings Host/IP field validation
    • Fixed Cumulocity authentication reset
    • Fixed Events Reporting rule saving

RUT9_R_00.07.00.2 | 2021.10.19

  • Fixes
    • Fixed NMEA sentence validation for Meig modems

RUT9_R_00.07.00 | 2021.07.16

  • New features
    • New, RUTX-like WebUI style
    • New WebUI based on Vue.js 2.6.12
    • RutOS updated to OpenWrt 19.07.7 base
    • DNP3 Master and DNP3 Oustation
    • 'Restore to user's defaults' SMS Utilities rule
    • DHCP Relay AT command
  • Improvements
    • Updated firewall to release 3
    • Updated kernel to version 4.14.221
    • Updated uhttpd to version 2020-10-01
    • Updated xtables-addons to release 9
    • Updated mwan to version 2.8.14
    • Updated pcre to version 8.44
    • Updated curl to version 7.74
    • Updated sqlite to version 3.33
    • Updated ncurses to version 6.2
    • Updated OpenSSL to version 1.1.1k
    • Added full MODBUS register address expansion specifier for Data to Server
    • Added full MODBUS register address legend
    • Added Client ID option for the MQTT protocol in Data to Server
    • Improved Data to Server sleeping accuracy
    • Improved Data to Server username validation; now space is allowed
    • Added firmware version OID to the SNMP service
    • Added IP address family option field to the SNMP page
    • Added SNMPv6 section to the SNMP Communities page
    • Renamed the 'System -> Users' page to 'System -> System Users'
    • Moved password changing option to the 'System -> System Users' page
    • Switched to ar8216 driver
    • Added IPsec XAUTH support
    • Improved OpenVPN updown, init scripts to write info about instance in JSON
    • Added AES-256-GCM encryption support to OpenVPN
    • Added extra configuration parameters to DMVPN
    • Added PSK conversion to DMVPN and single PSK types
    • Improved Package Manager package installation, deletion and dependencies
    • Improved Package Manager download process over FOTA
    • Added new Input/Output values manageable over RMS
    • Added IPv6 traffic logging
    • Made 'Network -> Failover' and 'Network -> Interfaces' page data draggable on multiple browsers
    • Added Input/Output Post/Get URL parameter t_time changing delay and time to seconds or miliseconds
    • Added message storage management by config value
    • Improved QMI error handling and status tracking
    • Turned on modem in preinit for correct power-on sequence
    • Added Post/Get feature to turn mobile data on/off
    • Added the possibility to use 2gonly/3gonly/4gonly arguments for cellular service command alongside current 2g/3g/lte arguments
    • Added "Phone number" and "Message" fields for "Send SMS" option
    • Added "Host to ping from SIM1" and "Host to ping from SIM2" fields
    • Added support for multiple USB to Serial adapters
    • Added option to send SMS warning messages to Hotspot users authenticated with SMS OTP when specified amount of data is used up
    • Added "send analog input" option to TAVL settings
  • Fixes
    • Added glib2 patch to fix CVE-2019-13012 vulnerability
    • Added ntfs-3g patch to fix CVE-2019-9755 vulnerability
    • Added WolfSSL patch to fix CVE-2021-3336 vulnerability
    • Added Busybox patch to fix CVE-2018-1000500 vulnerability
    • Added netifd, odhcp6c IPv6 routing loop on point-to-point links patches to fix CVE-2021-22161 vulnerability
    • Fixed Android clients IPsec MTU/MSS size
    • Fixed wrong IPsec DPD value saving
    • Changed IPsec PSK maximum length to 128 symbols
    • Fixed SSTP remaining up after package removal
    • Fixed DMVPN crypto_proposal write to config
    • Fixed I/O Juggler's SMS sending to correct group
    • Fixed I/O Scheduler's relay state issue
    • Added I/O direction check while changing IOs via I/O Post/Get
    • Fixed float endianness mismatch on some devices MODBUS TCP Master, MODBUS Serial Master
    • Fixed UPnP issue that caused config changes to apply only after service restart
    • Fixed WebUI files caching when upgrading firmware
    • Fixed WebUI date display format
    • Fixed MODBUS returning incomplete MAC address data
    • Fixed GPS time synchronization for DST regions
    • Fixed depleting IPv6 RA timeout when the ISP doesn't send RA updates
    • Added "Transaction timed out" error handling
    • Fixed PPPOE connection loss when wrong session PADT packet arrives
    • Added gcont object tracking and info update if this service is restarted
    • Fixed default SMS storage
    • Fixed SMS warning sending after Mobile Data Limit change
    • Fixed DHCP relaying over mobile networks
    • Changed PIN code maximum length to 8 symbols
    • Fixed 'I/O status' message to include correct Input/Output name based on info in ubus ioman objects
    • Fixed 'Over IP' serial type's UDP issue in client mode
    • Fixed DLNA connections count total in statistics page
    • Fixed WiFi Hotspot's Walled Garden issues
    • Fixed WiFi Hotspot data logging issues
    • Fixed P2P group information processing vulnerability in wpa_supplicant
    • Added validation to Walled Garden Address list field
Retrieved from "https://wiki.teltonika-networks.com/index.php?title=Template:Networking_rut9xx_firmware_change_log&oldid=100479"