RUTM50 Firmware Downloads

Main Page > RUTM Routers > RUTM50 > RUTM50 Firmware Downloads

This page contains firmware files for RUTM50 devices. Look to the table below or the changelog to find download links.

To upgrade firmware using WebUI, follow the instructions in RUTM50 Firmware.

RUTM50

File	Type	Release date	Size	MD5	Changelog
RUTM_R_00.07.10.3_WEBUI.bin	Latest FW	2024.11.08	24.13 MB	cd6fc1bce7c5063169f66f5751f8f475	Link
RUTM_R_00.07.10.3_WEBUI.bin	Mass production FW	2024.11.08	24.13 MB	cd6fc1bce7c5063169f66f5751f8f475	Link

RUTM_R_GPL_00.07.10.3.tar.gz

SDK

2024.11.08

39.28 MB

368687e910ac83dc61868497ec0a1156

Note: packages for Package Manager are independent from firmware and can be downloaded in the Package Downloads page.
Note: RUTM50 device firmware cannot be downgraded (only upgrades).

FW checksums

Checksums for firmware files can be found here.

Changelog

RUTM_R_00.07.10.3 | 2024.11.08

Fix
- Network
  - Kernel: fixed an issue with wi-fi not starting properly

RUTM_R_00.07.10.2 | 2024.11.04

New
- Network
  - Mobile: added "kajeet.gw12.vzwentp" APN for "Verizon" operator to APN database
  - Mobile: added "V5GA01INTERNET" APN for "Verizon" operator to APN database
  - Mobile: added "kajeet.fw5g.vzwentp" APN for "Verizon" operator to APN database
  - Mobile: added "iot.kajeet" APN for "T-Mobile" operator to APN database
  - Mobile: added "iot.tmowholesale.static" APN for "T-Mobile" operator to APN database
  - Mobile: added "iot.tmowholesale" APN for "T-Mobile" operator to APN database
  - Mobile: added "sentinel01.com.attz" APN for "AT&T" operator to APN database
  - Mobile: added "sentinelent01.com.attz" APN for "AT&T" operator to APN database
  - Mobile: added "sentinelnb01.com.attz" APN for "AT&T" operator to APN database
  - Mobile: added "213x.sentinel01.com.attz" APN for "AT&T" operator to APN database
  - Mobile: added "213x.sentinelent01.com.attz" APN for "AT&T" operator to APN database
  - Mobile: added "sentinel-static.mcs" APN for "AT&T" operator to APN database
  - Mobile: added "uscc05016.enterprise3.usc-cdp" APN for "US Cellular" operator to APN database
  - Mobile: added "uscc07009.enterprise3.usc-cdp" APN for "US Cellular" operator to APN database
  - Mobile: added "sentinel.crs.bell.ca.ioe" APN for "Bell Mobility" operator to APN database
  - Mobile: added "kajeet.crs.bell.ca.ioe" APN for "Bell Mobility" operator to APN database
  - Mobile: added "sentinel.apn" APN for "Rogers" operator to APN database
  - Mobile: added "sentinel.vf" APN for "Vodafone" operator to APN database
  - Mobile: added "sentinel.lpwa.vf" APN for "LPWA" operator to APN database
Improvements
- Network
  - Mobile: improved carrier aggregation signal value parsing
Fix
- Network
  - Firewall: fixed bug in NAT rule migration script that would overwrite Port Forwarding rule options
  - Mobile: fixed eSIM profile loading from servers with unusual response

RUTM_R_00.07.10 | 2024.10.10

New
- Network
  - Mobile: added ability to export modem debug and USSD responses to CSV file
  - Mobile: added "hologram" APN for "Hologram" operator
  - Mobile: added "wbdata" APN for "Granite" operator
  - Mobile: added "netw.vp" and "netw2.vp" APNs for "Networth" operator to APN database
  - NAT64: added "jool" package for NAT64 support
- Services
  - AWS IoT Core: added service
  - BACnet: added ability to configure several BIP interfaces, to set network numbers and preconfigure BDT entries for BBMD
  - Console: added service status information display
  - DLMS: added service status information display
  - DNP3 Client: added service status information display
  - DNP3 Outstation: added service status information display
  - GPS: added service status information display
  - Modbus Client: added service status information display
  - Modbus Server: added service status information display
  - Modbus TCP over Serial Gateway: added service status information display
  - Modem Control: added service status information display
  - MQTT Modbus Gateway: added service status information display
  - NTRIP: added service status information display
  - OPC UA Client: added service status information display
  - OPC UA Server: added variable "rut_wan_type" which shows if WAN is on a wired or a mobile network
  - OPC UA Server: added service status information display
  - RMS: added SOCKS5 proxy support
- System
  - Certificates: added SCEP certificate generation method
Improvements
- Network
  - Curl: added unix socket support
  - Firewall: added most options to basic mode for all firewall pages
  - Firewall: added all firewall pages to basic mode
  - Interfaces: increased interface metric maximum value from 10000 to 4294967295
  - Mobile: added network reject cause messages
  - Mobile: added "flolive.net" APN for "Telecom Italia", "Telefonica O2" and "Telefonica Movistar" operators to APN database
  - Mobile: changed the default APN for IMS protocol from "VZWIMS" to "IMS" for "Verizon" operator
  - Mobile: fixed an issue where the ICCID was not returned correctly when the SIM card's ICCID ended with letters
  - Mobile: improved 5G NSA CA information display
  - Mobile: improved SIM and eSIM management via LPAC service
  - Multi WAN: added rules table to basic mode
  - Network: improved performance under stateless single-directional traffic (RFC2544)
  - Network: improved throughput stability of "Hardware flow offloading"
  - Static Routes: added page to basic mode
  - VRRP: added page to basic mode
  - Wireless: added interface status message when DFS CAC is in progress
  - Wireless: added most options to basic mode
  - Wireless: added SSID creation and deletion to basic mode
  - Wireless: moved Travelmate from Package Manager to base Firmware
- Services
  - DLMS: added meter COSEM object scanning
  - DNP3 Client: made menu names more consistent
  - Hotspot: added "Coova-Chilli-SSID" (28) Vendor Specific Attribute for Radius
  - IPsec: improved 'Remote endpoint' validation to allow '%any', '%any4', '%any6' values and netmask
  - IPsec: added ability to use certificates from Certificate Manager
  - L2TPv3: added Tunnel ID and Session ID validation to avoid creating multiple tunnels with the same parameters
  - Modbus Client: updated Modbus Client menu position
  - Modbus Server: updated Modbus Server menu position
  - Python3: changed python3-light package libraries
  - SMS Utilities: added an option to enable or disable the return of status code message
  - Tailscale: improved status information by including health messages
  - Tinc: added options to set the tunnel's IP address
  - Tinc: added a port option to listen for incoming connections and the ability to specify a port for outgoing connections
  - Wireguard: added tunnel source mode selection
  - Python3: updated version to 3.11.7
  - Strongswan: updated version to 5.9.14
  - Tailscale: updated version to 1.70.0
- System
  - Access Control: refactored 'General', 'Security' and 'PAM' Web pages
  - Auto Reboot: added support for multiple hosts/URLs in Ping/Wget Reboot
  - Backup: encrypting backup does not require 7zip package anymore
  - Certificates: split "Let's Encrypt" certificates into multiple files
  - Troubleshoot: added dynamic routes debugging information
  - WebUI: added ability to open new page in new tab without entering user credentials
  - WebUI: improved SDK example application
  - Glib2: updated version to 2.80.5
  - Kernel: updated version to 5.10.224
  - Ncurses: updated version to 6.5
Fix
- Network
  - Firewall: fixed automatic priority option change
  - Mobile: fixed LTE band parsing while the modem is on limited service
  - Mobile: fixed hang up of QMI WDS service
  - Mobile: fixed QMI errors when multi APN is configured
  - Mobile: fixed typo in "m2m.airinternet.eu" APN for "Airinternet" operator in APN database
  - Network: fixed MTU change of WAN interface
  - Network: fixed mobile Bridge/Passthrough mode not working after changing LAN interface settings
  - Wireless: fixed BSSID show for interface in Client mode
  - Wireless: fixed showing incorrect transmit power
  - Wireless: fixed hostapd ubus call timeout after wireless configuration change
  - Wireless: fixed reporting disconnection from external AP when device in STA+AP mode
  - Wireless: fixed missing rx frame types needed for wifi scanner
- Services
  - BACnet: fixed communication issues between the ports
  - BACnet: added all available default baud rates
  - BGP: fixed AS field to allow duplicate values
  - BGP: fixed Access list filters not applying fully
  - DLMS: added all available default baud rates
  - DMVPN: fixed DMVPN GRE instance disappearing when creating new IPsec instance
  - DNP3 Client: removed unnecessary max length display for test response field
  - DNP3 Client: renamed TCP Station to TCP Client in the API documentation
  - DNP3 Client: added all available default baud rates
  - DNP3 Outstation: added all available default baud rates
  - GPS: fixed NMEA collecting and cache file path validations
  - GPS: added validation for missing required AVL options
  - GPS: fixed an issue where a firmware update with keep settings would remove existing hosts
  - GPS: fixed HTTPS hostname validation
  - GRE: fixed interface not showing up in OSPF and RIP selections if it is off
  - Hotspot: fixed blocklist not working when no addresses are provided
  - Hotspot: fixed uploaded custom landing page file permissions
  - Hotspot: fixed certificates to be required to enable https redirect
  - IPsec: fixed IP rule not appearing after network restart
  - IPsec: fixed duplicate port values in IPsec firewall rules
  - Ledman: fixed issue when power LED turns off when rebooting device
  - Modbus Client: added all available default baud rates
  - Modbus Client: added missing API docs for Modbus test request
  - Modbus Server: added all available default baud rates
  - Modbus Server: fixed firewall rule staying enabled when app is disabled
  - Modbus Server: fixed firewall rule creation
  - Modem Control: added all available default baud rates
  - NTRIP: added all available default baud rates
  - OpenVPN: fixed the configuration after disabling the use of external services
  - OpenVPN: fixed OpenVPN restarting when mobile interface comes up
  - Over IP: added all available default baud rates
  - SNMP: fixed Hotspot OIDs' hssID and hssUsername display
  - Tinc: fixed adding routes to remote subnets
  - Tinc: fixed configuration generation issues when creating multiple network and host instances
  - Tinc: fixed issues with route creation when using IPv6 addresses in tunnel configuration
  - Tinc: fixed validation for uploading key files
- System
  - Backup: fixed uploading backup with memory expansion enabled
  - CLI: fixed some private IPs being incorrectly determined as public
  - JSON-RPC: fixed login "Access Denied" error
  - Memory Expansion: fixed input element alignment issues
  - WebUI: added API required values validation when enabling BACnet, DLMS, DNP3, Modbus, MQTT, NTRIP services
  - WebUI: fixed 'Memory' status card progress bars visuals
  - WebUI: fixed search bar suggestions after removing packages
  - WebUI: fixed showing data in modals for users with only read permissions
  - WebUI: fixed custom SDK pages not loading correctly
CVE Patches
- CVE-2021-3520
- CVE-2021-44540
- CVE-2021-44541
- CVE-2024-4032
- CVE-2024-6119
- CVE-2024-6232
- CVE-2024-6923
- CVE-2024-7264
- CVE-2024-42225

RUTM_R_00.07.09.4 | 2024.10.02

Improvements
- Services
  - NTP Client: changed default NTP servers
Fix
- Services
  - NTP Client: fixed NTP server usage to work with next in line server if current server does not respond

RUTM_R_00.07.09.3 | 2024.09.27

Fix
- Network
  - Multi WAN: fixed ipsets not getting deleted correctly when Multi WAN gets restarted

RUTM_R_00.07.09.2 | 2024.09.16

Fix
- Network
  - Mobile: fixed RM520N modem connection issue after device reboot

RUTM_R_00.07.09.1 | 2024.09.13

Improvements
- Services
  - Python3: updated version to 3.11.7
Fix
- Network
  - Mobile: fixed eSIM profile config generation

RUTM_R_00.07.09 | 2024.09.03

New
- Network
  - Devices: added VXLAN support
  - Firewall: added ability to configure NAT rule action
  - Firewall: added additional TTL target for firewall rules
  - Mobile: added "datamobile.ag" APN for "Datamobile.ag" operator to APN database
  - Mobile: added "m2m.ajrinternet.eu" APN for "Airinternet" operator to APN database
  - Mobile: added "wbdata" APN for "Webbing" operator to APN database
  - Mobile: added "inetd.vodafone.iot" APN for "Vodafone" operator to APN database
  - Mobile: added "asm" APN for "ASM" operator to APN database
  - Realtime Traffic: added historical traffic charts
  - Realtime Traffic: added overall quality measurement to wireless signal charts
  - Wireless: added option to enable 802.11w Management frame protection when using non-WPA3 encryption
- Services
  - Events Reporting: added new firmware version notification event
  - SNMP: added Multiwan data module
- System
  - WebUI: added notifications menu
Improvements
- Network
  - Mobile: improved network bring up after operator scan
  - Mobile: updated bands selection to include band number and frequency
  - Mobile: improved SIM card notifications to get removed when SIM card state or active SIM changes
  - Mobile: improved modem update notifications to show modem name
  - Mobile: removed the USSD feature from the data-only modems
  - Ports Settings: added more PoE state symbols, colored disabled port differently and improved port status hint
  - Realtime Traffic: improved chart styles
  - Wireless: increased EAP authentication logging
  - Wireless: added various validations for network that is being used by wireless interface
  - Wireless: added insecure configuration warnings when configuring SSIDs
  - Wireless: updated wireless cards to display each radio device's signal quality and band data
  - Wireless: reduced time required for Fast Transition in STA mode
- Services
  - Call Utilities: added check if the number is blocked before doing action
  - Data to Server: added warning messages about insecure certificates for http_certfile and mqtt_certfile options in API and WebUI
  - DLMS: added SHA256 authentication
  - DLMS: improved COSEM group enable validation
  - GRE: reduced GRE keepalive packet buffer size
  - Hotspot: increased throughput performance
  - Hotspot: increased maximum length of 'Local users' username to 255 characters
  - Hotspot: added walled garden allowlist and blocklist
  - IPsec: added support for route based tunnel
  - L2TP: added field for custom options
  - SMPP: added timeout option
  - Web Filter: added hostname count message after successful file upload
- System
  - Access Control: improved system user's access control rules logic
  - Access Control: added option to disable password auth for the root user
  - Administration: improved write/read access control options display to match meniu path style
  - Backup: improved backup page by splitting it into backup and reset settings page
  - Boot: added NAND image verification after firmware flash
  - Side Widget: added port status widget
  - Update Firmware: changed firmware update log to include firmware version
  - WebUI: updated firmware and backup verification pages design
  - WebUI: improved global alerts display
  - WebUI: added confirmation prompt for disabling service in side widget
  - Kernel: updated version to 5.10.221
Fix
- Network
  - Devices: fixed configured VLAN 0 device cannot be selected in interface physical settings configuration
  - Mobile: fixed data limit widget to show used data for inactive interface
  - Mobile: fixed Bridge/Passthrough modes for routed networks
  - Mobile: fixed incorrect date values when setting SMS limit
  - Mobile: fixed SINR display for EG060K module
  - Mobile: fixed SMS used data header counter
  - Mobile: fixed the issue where the PUK event was not displayed when the SIM PIN was blocked
  - Mobile: fixed uqmi start-network authentication issue
  - Mobile: fixed modem info not being filled on devices with more than one modem
  - Mobile: fixed mobile data limit to calculate correct used limits when using ipv4 and ipv6 simultaneously
  - Mobile: fixed USSD over IMS error handling
  - Mobile: fixed an issue where the interface could hang if the modem was busy
  - Network: fixed incorrect date values when setting data limit
  - RelayD: fixed relayd assigning wrong interface to zone
  - Wireless: fixed station mode connection issues for 2.4 GHz radio in STA+AP mode
  - Wireless: fixed wireless status API response to contain separate interface information for multiple radio configurations
- Services
  - Azure IoT Hub: fixed the Azure IoT Hub deprecated endpoint to create Data to Server sections
  - Azure IoT Hub: fixed the Azure IoT Hub deprecated endpoint so that it does not create sections in GET request
  - Azure IoT Hub: fixed the deletion of Data to Server sections when an Azure IoT Hub section is deleted through the deprecated endpoint
  - DLMS: fixed OBIS code validation
  - GPS: fixed an issue where a firmware update with keep settings would remove existing hosts
  - GPS: fixed NMEA forwarding when RMC/GGA were not synchronized when using same interval
  - Hotspot: fixed 'Hotspot network' input validation to only allow network mask from 16 to 30
  - Input/Output: added I/O juggler reload when I/O pin direction is changed
  - OPC UA Client: fixed TCL file upload
  - OPC UA Server: fixed TCL file upload
  - OPC UA Server: fixed configuration migration
  - OpenVPN: fixed default firewall zone for tap interfaces
  - SNMP: fixed negative GPS latitude display
  - SNMP: fixed TELTONIKA-MIB wireless module crash
  - SNMP: fixed mobile network state display
  - SNMP: fixed default hssDwLimit, hssUpLimit, hssDwBandwidth and hssUpBandwidth values
- System
  - API Core: fixed file deletion
  - Package Restore: fixed automatic package re-installation after firmware upgrade
  - Troubleshoot: fixed troubleshoot not including all the log files when log to flash is enabled
  - User Settings: fixed page to show groups and users if the user has been granted access
  - WebUI: fixed overview page to display active wireless (WLAN) clients
CVE Patches
- CVE-2021-32292
- CVE-2022-40617
- CVE-2023-49441
- CVE-2024-0397
- CVE-2024-3596
- CVE-2024-5535
- CVE-2024-8088
- CVE-2024-26669
- CVE-2024-26739
- CVE-2024-26740
- CVE-2024-36901

RUTM_R_00.07.08.2 | 2024.08.12

Fix
- System
  - Update Firmware: fixed inconsistent firmware download from FOTA

RUTM_R_00.07.08.1 | 2024.08.06

Note: This firmware version was removed due to an issue with FOTA firmware download.

Improvements
- Network
  - Mobile: improved firmware downgrade validation for Quectel modules
- Services
  - Zerotier: updated version to 1.14.0
Fix
- Network
  - Mobile: fixed wrong bandwidth parsing on 5G devices
  - Mobile: fixed an issue where in some cases mobile network interfaces would not be brought down properly
  - Mobile: fixed memory fault while allowlist and denied data roaming enabled
  - Mobile: fixed illegal instruction fault on modem control services
  - Network: fixed default route not being added for PPPoE connections
- Services
  - Modbus TCP over Serial Gateway: fixed serial connection not working after reboot
  - OPC UA Client: fixed connections not being closed after using testing functionality
- System
  - WebUI: fixed SDK WebUI package compilation

RUTM_R_00.07.08 | 2024.07.18

Note: This firmware version was removed due to an issue with FOTA firmware download.

New
- Network
  - 802.1X: added client support
  - DNS: added inherited server status to configuration page
  - HTTPS DNS Proxy: added new HTTPS DNS Proxy package to package manager
  - Mobile: added SIM card lock/unlock functionality in Mobile->Utilities page
  - Mobile: added SIM card PIN change functionality in Mobile->Utilities page
  - Mobile: added new Mobile->Limits page which shows information and allows to configure Data and SMS limits
  - Mobile: added DFOTA support for RG520N modems
  - Mobile: added nr-arfcn display to mobile status page
  - Mobile: added dfota support for devices with RG520N-EB modem
- Services
  - Data to Server: added 'Lua script' data input
  - Hotspot: added Single Sign-on (OIDC) authentication mode
  - Hotspot: added Walled Garden blocklist functionality
  - Input/Output: added ability to configure gpio debounce timer and changed default gpio debounce timer value from 200 ms to 10 ms
  - IPsec: added initial XFRM support
  - MQTT Modbus Gateway: added JSON message type format
  - OpenVPN: added DCO support
- System
  - API Core: added option to configure api session timeout
  - Certificates: added "Let's encrypt" certificate generation
  - PAM: added RADIUS external user support
  - UI Core: added data analytics support
  - Update Firmware: added warning message about device being temporarily unreachable on firmware update
Improvements
- Network
  - Channel Analysis: added scan error message when a DFS channel and FCC country are selected
  - DNS: separated field "DNS forwardings" into two: one for simple server forwarding other for domain-specific
  - DNS: moved "DNS Forwardings", "Listen interfaces", "Exclude interfaces", "Local service only", options to advanced tab
  - Firewall: improved protocol field in all firewall pages by making that "All" value would be mutually exclusive with any other value
  - Mobile: improved IMS context initialization
  - Mobile: updated SMS memory management for multipart SMS
  - Mobile: added error message when attempting to enable the SIM switch without any criteria set
  - Mobile: added informative message in SIM switch page when Data/SMS limit criteria are enabled but the limits themselves are not set up
  - Mobile: moved operator list allowlist/blocklist selection to Network selection page
  - Mobile: refactored Scanned operators modal, added repeat scan button
  - Mobile: added ability to view previously scanned operators in Network selection and Operator lists pages
  - Mobile: added ability to edit operator list name and initiate scans for operators in Operator lists page
  - Mobile: updated operator code field list to include APNs from the APN database in Operator lists page
  - Mobile: split Mobile->General page into three pages: General, Connection and Utilities pages
  - Mobile: added mobile interface with highest priority APN configuration in Mobile->General page
  - Mobile: added icons with hints which show SIM card, operator, data connection statuses in Mobile->General page
  - Mobile: moved Mobile data limit section to a tab in WAN page
  - Mobile: added informative message in WAN page to indicate whether the connection will be made using APN from APN database, empty or custom APN
  - Mobile: improved logging of ping error messages
  - Mobile: added 5G SA/NSA mode selection
  - Mobile: improved modem updater to stop ping reboot service while update is in progress
  - Mobile: improved the handling of denied messages upon SIM switch
  - Mobile: added notification when a multi-IMSI SIM card is using Auto APN
  - Mobile: added validation to not allow passthrough and bridge mode when one already exists
  - Mobile: improved safeguards for modem services startup
  - Mobile: improved modem update status display
  - Mobile: added corrupted mobile statistics database restoration functionallity
  - Mobile: improved setting of IPv4 and IPv6 types inside the modules
  - Mobile: improved provider name parsing for SLM750 modem
  - Multi WAN: improved interface status representation when using load balancing
  - Network: added more options for "IPv6 assignment length" field
  - Wireless: added warning when user configures mesh on radio with automatic frequency channel
  - Wireless: added support for wireless MAC-filter MAC ranges
  - Wireless: changed Radius Accounting port is not required when configuring access point with enterprise encryption
  - Wireless: enabled ACS(automatic channel selection) for 5 GHz radios by default
  - Wireless: refactored radio configuration page layout
  - Wireless: refactored assignment of wireless interfaces MAC addresses, STA interface will always use fixed address
- Services
  - Azure IoT Hub: added DPS symmetric key attestation support
  - Azure IoT Hub: added Direct Method support
  - Azure IoT Hub: added Plug and Play integration
  - Azure IoT Hub: added link to "Data to Server" page
  - Data to Server: added support for multiple filters
  - Data to Server: improved HTTP output hostname definition with automatic protocol specification in URL
  - Data to Server: improved MQTT input connection handling
  - DNP3 Client: added option to enable/disable service
  - GPS: added send empty feature, which sends zeroed location data after specified GNSS loss timeout
  - GRE: increased Inbound and Outbound key limit to 4294967295
  - Hotspot: adjusted hotspot user manager page to display active and inactive user sessions
  - Hotspot: changed local users to be stored with other types of users
  - Hotspot: added 'noc2c' option for enabling client isolation, option is enabled by default
  - Input/Output: added custom name support in I/O status page
  - IPsec: added certificate warning message
  - Mobile Utilities: added interface option to sms_utils cellular command
  - Mobile Utilities: improved error log message
  - Mobile Utilities: improved naming of I/O pins in initial I/O status rule
  - Mobile Utilities: sms utilities authentication brute force prevention
  - Modbus Server: added mobile last month and last week usage registers
  - Modem Control: disabled canonical mode by default for partial mode. Now full/partial mode input from serial port works the same way
  - Mosquitto: added large package size check for MQTT clients
  - MQTT Modbus Gateway: improved mosquitto reconnect time and service will try to recover few times before exiting
  - MQTT Publisher: improved MQTT connection handling
  - OPC UA Client: added security modes
  - OPC UA Server: added security modes
  - OPC UA Server: added service status display
  - OpenVPN: added support for decrypting private key when uploading a configuration file
  - OpenVPN: improved instance status state
  - OpenVPN: added options to specify an IP address pool for dynamic assignment to clients
  - Over IP: added label to show how many servers a client is connected to
  - Over IP: connect on data feature will not disconnect immediately after data transfer but wait for inactivity timeout
  - Over IP: increased TLS handshake timeout to 10 seconds
  - SMPP: added brute-force prevention
  - SMPP: added TLS/SSL support
  - SMS Utilities: added security warning in "Authorization method" configuration
  - SNMP: changed interface module OID structure
  - SNMP: improved User-based Security Model (USM) brute force attack prevention measures
  - Stunnel: improved global instance settings dependencies
  - emailrelay: updated version to 2.4.1
  - OpenVPN: updated version to 2.6.9
  - stunnel: updated version to 5.72
  - Tailscale: updated version to 1.68.1
- System
  - Access Control: added certificate key length warnings
  - Access Control: adjusted access control when all pages are blocked
  - Access Control: added certificate file download for CLI to work on all browsers
  - API Core: implemented functionality to include warning messages for vulnerable certificates
  - Boot: enabled HW watchdog in bootloader
  - Boot: improved modem startup reliability
  - Package Manager: added multi package actions
  - Package Manager: added status filter
  - Package Manager: moved package upload action to main page
  - Package Manager: added links to installed packages pages
  - Package Manager: refactored "Packages" page
  - Package Manager: updated opkg repository link to use https
  - RutOS: improved GPL example page to align with new software architecture
  - Troubleshoot: refactored Modem debug section to display responses in single field, added clear button to remove received responses
  - Troubleshoot: added support for multiple syslog servers
  - UI Core: added additional message with IP address to loading screen for scenarios when redirect to different IP address happens
  - UI Core: added toast message hiding when text is too long
  - Update Firmware: added 'Firmware version' data in screen after firmware upload
  - WebUI: added functionality to cancel loading screen if it takes 30 or more seconds
  - WebUI: removed all ubus method calls from webui
  - WebUI: improved language caching
  - WebUI: added password generator for first login modal
  - WebUI: added sticky position to side menu
  - WebUI: added default password hint to login error message
  - WebUI: added warning messages for low-security certificates
  - Kernel: updated version to 5.10.217
  - libexpat: updated version to 2.6.2
  - SSL/TLS: updated version to 3.0.14
  - vue: updated version to 3.4
Fix
- Network
  - Channel Analysis: fixed network list not being updated if a single scan fails
  - Devices: fixed missing API devices status endpoint permission
  - DHCP: fixed "DHCP option" allow empty input value
  - DHCP: fixed IPv4 leases being not correctly shown when NTP synchronizes time
  - DHCP: fixed DHCP error that occurred after changing the subnet of the LAN IP address in the setup wizard
  - Dynamic routes: fixed duplicated external routes cards
  - Firewall: fixed firewall zone validation when adding interfaces
  - Mobile: fixed low signal reconnect being available on modems where it is not supported
  - Mobile: fixed gsmctl -E output to return only json values
  - Mobile: fixed Carrier Aggregation signal strength info
  - Mobile: fixed wrong mobile data limit used data format for sms messages
  - Mobile: fixed duplicate data connection event reporting
  - Mobile: fixed an issue where low signal notifications were displayed without a SIM card
  - Mobile: fixed modem serial number acquisition after modem reboot
  - Mobile: fixed an issue when 4G-only network type selection may have resulted in a slower connection to the operator
  - Mobile: fixed issue where USSD responses were returned in HEX format instead of text format for EC200A module
  - Mobile: fixed issue where DHCP filter was not set correctly for RG501Q
  - Mobile: fixed an issue where the wrong IP address was used after a DFOTA upgrade
  - Multi AP: fixed Multi AP not working with fast roaming
  - Multi AP: fixed switching to Multi AP mode fails due to encryption
  - Multi AP: fixed Multi AP configuration being deleted when switching mode on the same radio device
  - Network: fixed overriding MAC address for interfaces that are bridged
  - Realtime Traffic: fixed mobile usage by week day translation by device language
  - RelayD: fixed API error when "network" and "lan_mark" options are not present in a PUT request
  - SQM: fixed missing PPP mobile device selection in SQM configuration
  - Wireless: fixed wireless scan results sometimes not being returned
  - Wireless: fixed 5 GHz Wi-Fi scanning is prohibited when a DFS channel and ETSI regulatory domain is selected
  - Wireless: fixed Wi-Fi 5 GHz unsupported channel selection issue on specific widths
  - Wireless: fixed wireless status page not updating wireless SSID status after page is opened
  - Wireless: removed the ability to have different countries in radio configurations
  - Wireless: fixed interface delete when it's unassigned from the wireless interface in access point mode
  - Wireless: fixed backticks for WiFi SSID are not allowed in WebUI
- Services
  - BACnet: fixed incorrect BACnet IP port used for sending responses
  - BGP: fixed route map sequence going out of range
  - BGP: fixed listen range field allowing multiple entries
  - Call Utilities: fixed table header switch to be disabled if no rules were created
  - DLMS: fixed DLMS test response format
  - DLMS: fixed COSEM group validation
  - DLMS: fixed API POST error for /dlms/devices/config endpoint
  - DLMS: fixed serial connection not working after reboot
  - DNP3 Client: fixed to allow reading objects past 255 index
  - DNP3 Client: fixed incorrect hints
  - DNP3 Outstation: fixed serial outstation starting issues
  - GPS: fixed GPS start constellations issue
  - GPS: fixed an issue where NMEA sentences were parsed incorrectly at midnight, resulting in a 24-hour time discrepancy
  - GPS: fixed gpsctl datetime parameter
  - GPS: fixed issue where DPO would not get disabled if GPS is started without DPO
  - GPS: fixed AVL TAVL rule signal value issue
  - GPS: fixed default AVL rule issue where I/O would be ignored by default
  - GPS: fixed BeiDou and QZSS seperation in PQGSV sentences
  - GPS: fixed NMEA sentences reading in NMEA collecting
  - Hotspot: fixed uploading more than one custom theme
  - Hotspot: fixed creating Hotspot to SSID that is disabled
  - Hotspot 2.0: fixed Venue name and Operator's name field validations
  - I/O Juggler: fixed improper dout action config handling
  - I/O Juggler: updated profile change action
  - Input/Output: allow unselecting all Post/Get access methods
  - IPsec: fixed connectivity issues when using WAN failover
  - IPsec: fixed the instance status when the local firewall option is disabled
  - Ledman: fixed issue when after some time network type LED starts blinking
  - Modbus Client: fixed test request option validation
  - Modbus Client: fixed alarm output action display values
  - Modbus Client: fixed incorrect period hint
  - Modbus Server: fixed APN register not clearing APN
  - Modbus Server: fixed 148 and 164 modbus registers
  - Modbus Server: fixed incorrect hints
  - Modem Control: fixed API POST request validation
  - NTRIP: fixed NTRIP NMEA generation timestamp and coordinates errors
  - NTRIP: fixed configuration reading with several instances added
  - OPC UA Server: fixed not starting while modem is down
  - OpenVPN: fixed displaying imported files from device
  - OpenVPN: fixed the private key decryption for cases when a password is used
  - OpenVPN: fixed data cipher migration
  - Over IP: fixed issue where serial device does not recover after modem reboot
  - Over IP: fixed connect on data initiating TCP connection after few data transfers
  - SMPP: fixed username bypass problem
  - SMPP: fixed password validation
  - SMS Gateway: fixed SMS to Email recipient formatting according to RFC5322
  - SNMP: fixed GSM mSignal OID value type
  - SNMP: fixed GSM module memory leaks
  - SSTP: fixed functionality when the default route option is not enabled
  - Web Filter: fixed whitelist not working for some hosts when using IPv6
- System
  - Administration: fixed repeated validation on cleared inputs and added validation when new password matches the old one
  - API Core: fixed API method validation during upload action
  - API Core: fixed error messages for POST method
  - API Core: fixed option list validation
  - Boot: fixed factory settings restore (firstboot) not deleting hidden files
  - Events Log: fixed refresh button in event log table
  - IP Block: fixed adding MAC addresses back to whitelist when unblocking all of them
  - Memory Expansion: fixed enable validation
  - Recipients: made phone number field required
  - Setup Wizard: fixed lan ip step not changing ip address
  - Troubleshoot: fixed system log and kernel log buttons to be enabled with read only rights
  - Update Firmware: fixed misleading "Firmware version" status of "N/A" to "FOTA service is disabled" when FOTA is disabled
  - Update Firmware: fixed issue when infinite spinner appears after updating device firmware from server without having internet connection
CVE Patches
- Patched CVE-2023-52425
- Patched CVE-2023-52530
- Patched CVE-2024-25629
- Patched CVE-2024-28757

RUTM_R_00.07.07.3 | 2024.06.25

Fix
- Network
  - WebUI: fixed port advertisement change
- System
  - FOTA: fixed config when upgrading from older firmware with keep settings
CVE Patches
- CVE-2024-31950
- CVE-2024-31951

RUTM_R_00.07.07.2 | 2024.06.12

Improvements
- Network
  - Zerotier: added backup WAN interface blacklisting if WAN failover is enabled
  - Mobile: improved communication stability with eSIM
  - Mobile: improved parsing of multiple 5G bands
- Services
  - SNMP: added bruteforce attack prevention when using SNMP v3 user
  - L2TP: improved reconnect attempt logic
  - Wireless: removed unnecessary information from system logs
- System
  - SSH: removed weak SSH algorithms
  - Telnet: moved to Package Manager
Fix
- Network
  - BGP: fixed instance migration issues
  - Mobile: fixed a SIM detection issue
  - Mobile: fixed forced APN configuration
- Services
  - DMVPN: fixed duplicate NHRP map entries creation
  - OpenVPN: added fixes for the insecure tls-cert-profile option usage
- System
  - IP Block: fixed blocking of UDP traffic
  - Ledman: fixed WiFi LED indication when WiFi configuration is changed
CVE Patches
- CVE-2024-31948

RUTM_R_00.07.07.1 | 2024.05.03

New
- Network
  - WebUI: added ESM/EMM message notifications
  - WebUI: added internet status tracking configuration and overview widget
  - LAN: added a new IPv6 LAN status page
  - Static Leases: added a new IPv6 Static Leases page
  - WebUI: added custom domain name resolve option in “DNS” configuration page
  - Auto APN: added “uno.au-net.ne.jp” APN for “KDDI” operator
  - Auto APN: added 'eprivate010.tisparkle.com' APN for “Sparkle” operator
  - QoS: added mobile interface select option
  - Mobile: added framed routing support
  - Mobile: improved connection establish time for uqmi protocol
  - Failover: added additional connection flush options
  - Wireless: added auto-reconnect disable functionality
  - Wireless: added ability to use PKCS#12 certificates for EAP-TLS authentication
  - VRF: added initial Virtual Routing and Forwarding support
- Services
  - Post/Get: added I/O invert support
  - DLMS Client: added persistent TCP connections
  - Events Reporting: added unexpected shutdown event
  - Modbus Client: added 64bit data types
  - IPerf3: added iPerf3 to Package Manager
  - DNP3 Outstation: added I/O objects
  - Modbus Serial Server: added option 'Mobile data type'
  - TR-069: added PCI, LAC, TAC, EARFCN and Neighbour cells data to Device.MobileInfo node
  - Hotspot: added domain and subdomain options for external landing page
  - Over IP: added option 'Keep alive enable'
- System
  - WebUI: added the ability to generate random passwords for password input fields
  - WebUI: added reset to “Factory defaults” option
  - System: changed firmware certificate verification tool
  - IP Block: added time-based login attempt blocking
  - WebUI: added firmware update notification support
  - PAM: added the ability to set port for TACACS+
  - Logging: added multiple remote syslog servers support
Improvements
- Network
  - Static Leases: added possibility to use MAC with wildcard
  - WebUI: added ability to disable modem update notifications
  - Topology: changed network devices scanning application
  - WebUI: improved design of Status - LAN page
  - DHCP: simplified DHCP configurations in other pages and moved full DHCP configuration to a separate page
  - DHCP: removed default disabled server configuration for WAN interface
  - WebUI: simplified data entry of DNS forwardings by separating hostname and IP address fields
  - BGP: added Virtual Routing and Forwarding (VRF) support
  - BGP: added multiple BGP instance support
  - WebUI: adjusted responsive design breakpoints
  - WebUI: added additional field for warning threshold to allow entering value as percentage in Mobile Data Limit section
  - Mobile: improved mobile services stability when SIM card is lost during SMS sending
  - Mobile: updated bridge/passthrough mode logic to flush ARP and add static ARP entry if MAC is specified
  - Mobile: improved SIM switch logging and protection on failure to acquire data
  - WebUI: added partial data loading to APN database page
  - Mobile: improved SMS sending timeouts during network issues
  - Mobile: improved connection handling when data limit is reached
  - Mobile: added metric to default gateway when using passthrough mode
  - WebUI: added validation for 2 same APNs
  - WebUI: updated Band selection field to show duplex modes in Mobile General page
  - WebUI: added an information icon and disabled delete button for wireless instance when it is associated with a hotspot interface
  - Wireless: improved hidden AP handling when showing scan results
  - Wireless: added a range of channels to 5 Ghz radio to use as fallback if it drops after radar detection when using DFS channel
  - Dnsmasq: updated dnsmasq to version 2.89
- Services
  - Wireguard: added option to bind tunnel to a specific interface
  - OPC UA Client: added limits (10 servers, 20 groups, 50 nodes per server, 50 values per group)
  - DLMS Client: increased maximum count of connection sections to 30
  - DLMS Client: added short name referencing
  - SNMP: set strict default community access when IPv6 address is used
  - SNMP: improved sysName OID to set device's hostname
  - Network Shares: moved to Package Manager
  - Auto Reply: added available SMS message parameters to "Message text" input
  - Modbus Client: allow using diacritics in SMS alarms
  - Hotspot: moved MAC blocking option from Access Control to Hotspot page
  - WebUI: added MAC authentication support when using RADIUS authentication mode
  - WebUI: moved licenses to footer
  - AVL: added HDOP in TAVL settings
  - AVL: added ADC and ACL I/O types for secondary AVL rules
  - NTRIP: added a limit of 20 configurations
  - OpenVPN: added the bridge option for selecting the network device to be bridged with
  - OpenVPN: added possibility to create more than one TAP client
  - SSTP: updated package version to 1.0.19
  - Mosquitto: updated package version to 2.0.17
  - Tailscale: updated package version to 1.62.1
- System
  - WebUI: added more strict password requirements for restoring backup
  - SMTP: added option to either not verify SMTP server or upload SMTP server's CA file to verify authenticity
  - WebUI: Added the ability to choose the ROOT CA when using certificates from the device
  - WebUI: unified time format to ISO8601 across the entire WebUI
  - WebUI: added ability to choose imported certificate and key as 'Server certificate' and 'Server key' in 'Access Control'
  - WebUI: added 'Hosts' and 'IP Addresses' options for 'Simple' certificate generation and certificate signing
  - WebUI: changed firmware update option to server as a default option
  - WebUI: improved first login password change logic
  - Certificates: updated Root CA certificates
  - GPL: added offline package preparation command for GPL builds
  - Speedtest: added multiple connections support to improve accuracy
  - Libcap: updated package version to 2.69
Fix
- Network
  - Topology: fixed showing interfaces with assigned VLAN
  - WebUI: fixed static routing creation for GRE instance
  - Network: fixed DHCPv4 relay mode enabling
  - Mobile: fixed PIN code set after modem restart
  - Mobile: fixed cases where 5G NSA network type was shown incorrectly
  - Mobile: fixed an issue where using SIM change command on one SIM slot modems would reset connection
  - Mobile: fixed an issue where message storage would not be checked correctly
  - Mobile: fixed temperature value sometimes returning 0
  - Mobile: fixed denied roaming flag set
  - SIM Switch: fixed an issue when low "Check interval" was causing connection to fail
  - SIM Idle Protection: fixed problem when the SIM slot remained unchanged
  - Mobile: fixed an issue where SIM switch would fail when switching to PUK blocked SIM
  - Mobile: fixed an issue where sim switch would be executed twice immediately causing sim to not be switched
  - Mobile: fixed SIM PIN saving for non primary SIM cards
  - Failover: fixed Failover missing active rules when using multiple source and destination IP addresses
  - Failover: fixed an issue where failover would not function correctly while using a mobile interface
  - Failover - WebUI: fixed network and failover interface metric sorting synchronization issue
  - Failover - WebUI: fixed failover rule policy save issue with newly added WAN interface
  - Interfaces: fixed failover value for new WAN being taken from WAN that was just deleted
  - Wireless: fixed Wifi Scanner not saving scanned WiFi SSIDs
  - Wireless: fixed missing CCMP-256 and GCMP-256 cipher types in scan results
  - Wireless: fixed missing GCMP-256 cipher when using WPA3-EAP encryption in Client mode
  - Wireless: fixed skipped MAC address value for interface in Client mode
  - Wireless: fixed issue which caused client interfaces to not connect after device reboot
  - Wireless: fixed setup issue when client or mesh interfaces are configured on both radios
  - WebUI: fixed mesh nodes not being shown in Status->Wireless->Interfaces page
  - WebUI: fixed proposed configuration settings when connecting to a mesh point network
  - MultiAP: fixed client not switching to another AP if incorrect password was provided
- Services
  - Modbus Client: allow using negative floating point values in requests
  - Azure IoT Hub: fixed Data to Server minor WebUI dependency bugs
  - Data to Server: fixed DLMS data formating
  - Data to Server: fixed Network link state data display
  - DLMS Client: fixed segfault while reading profile generic COSEM object
  - DLMS Client: fixed profile generic entries reading
  - DLMS Client: fixed application memory allocation issues
  - SSTP: fixed route adding when default route is enabled
  - SNMP: fixed VLAN OID naming
  - OpenVPN: added fixes for instance status tracking functionality
  - OpenVPN: resolved uptime counting issues
  - PPTP: fixed PPTP instance deletion problem
  - Azure IoT Hub: fixed 'contentType' telemetry message parameter
  - Hotspot: fixed password validation for locally created users and signed-up users
  - Hotspot: fixed session invalidation after deleting registered user
  - Hotspot: fixed SMS OTP password reuse
  - Hotspot: fixed firewall rule creation
  - PPTP: fixed problem related with routes when failover is enabled
  - Modbus Client: fixed issue where service freezes when SMS alarm is sent
  - Modem over serial: improved robustness against modem reboots
  - Modbus TCP Over Serial Gateway: fixed gateway returning corrupted data with larger baud rates
  - Modbus Server: updated 'GPS fix time' register to store the UTC date and time of GPS position
  - WebUI: fixed data loading error in Input/Output > Post/Get page
  - UPnP: updated package version to 2.3.4
- System
  - NTP Client: fixed ‘Count of time synchronizations’ execution when synchronization to mobile operator is chosen
  - Package Manager: fixed spinner message when restarting network after package upload or download
  - Package Manager: fixed supported devices check when installing a package from server
  - WebUI: fixed language install from uploaded package after upgrade with keep settings
  - WebUI: fixed an issue when a user was not logged out after changing profiles
  - Telnet: fixed segmentation fault during concurrent connections
  - CLI: fixed enter key issue on mobile chromium based browsers
  - System Users: fixed SSH session close after deleting user or disabling SSH access
  - Profiles: fixed profile migration with installed packages
  - JavaVM: fixed package installation
  - WebUI: fixed Hotspot log page table search functionality
  - Speedtest: fix missing download speed on some servers
  - PAM: updated libpam to version 1.6.0
CVE Patches
- CVE-2022-4603
- CVE-2022-23308
- CVE 2022-45061
- CVE-2023-0466
- CVE-2023-6129
- CVE-2023-7042
- CVE 2023-24329
- CVE 2023-27043
- CVE-2023-31083
- CVE-2023-42366
- CVE-2023-46218
- CVE-2023-46219
- CVE-2023-46752
- CVE-2023-46753
- CVE-2023-48795
- CVE-2024-2397
- CVE-2024-25062
- CVE-2024-27913
- CVE-2024-22365

RUTM_R_00.07.06.10 | 2024.04.04

Fix
- System
  - Ledman: fixed memory leak

RUTM_R_00.07.06.8 | 2024.03.25

Firmware R_00.07.06.8 was removed due to an issue with inefficient memory allocation for LED control.

Improvements
- Services
  - IPSec: disabled libgmp in favor of openssl
  - IPSec: updated Strongswan to 5.9.6
Fix
- Services
  - IPSec: increased charon load timeout
  - IPSec: fixed loading of large private keys

RUTM_R_00.07.06.6 | 2024.03.04

New
- Services
  - Added domain and subdomain options for external landing page in Hotspot
Improvements
- System
  - Minified *.svg WebUI files to save space on the device
  - Removed unused easy-rsa package to increase free space
Fix
- Network
  - Fixed mobile daily data usage representation
  - Fixed the issue with Wireless bgscan functionality not operating correctly
- Services
  - Fixed OverIP serial utility issue where after some time server mode can't accept incoming connections anymore

RUTM_R_00.07.06.5 | 2024.02.21

New
- Network
  - Added support for multi line USSD
Improvements
- Network
  - Improved DMZ to use its source zone on port forwards creation
- System
  - Updated netifd version to 2024-01-04
  - Updated PPP package version to 2.4.9
  - Updated E2fsprogs package version to 1.47.0
  - Updated Musl package version to 1.2.4
Fix
- Network
  - Fixed an issue where DNS resolution failed for wireless clients connected to an access point configured on a specific VLAN
- Services
  - Fixed Modbus TCP Over Serial Gateway crash occurring at start up in some edge cases
  - Fixed tailscale VPN firewall zone creation issue
  - Fixed custom GPS NMEA prefix
- WebUI
  - Fixed action descriptions in the traffic rules table
  - fixed BACnet allow remote access functionality
- System
  - Fixed WiFi LED indication when access point is turned off
  - Fixed year 2038 problem with time counter overflow

RUTM_R_00.07.06.3 | 2024.01.17

Improvements
- Services
  - Added multiple hosts support for GPS HTTPS, NMEA and AVL services
  - Increased DLMS Client connection timeout for TCP sockets
Fix
- Services
  - Fixed DLMS Client memory leak with profile generic COSEM class
  - Fixed function 5 not working with high register numbers in MQTT Modbus Gateway service
- WebUI
  - Fixed Events Log sorting and search features
- System
  - Patched CVE-2024-0193 vulnerability
  - Patched CVE-2023-51779 vulnerability
  - Updated OpenSSH to 9.6p1 version, fixed CVE-2023-51385 and CVE-2023-51384
  - Fixed profile migrations, added error handling when trying to change profile while it is still applying

RUTM_R_00.07.06.1 | 2024.01.04

Fix
- Services
  - Fixed issue with NTPclient zombie processes
- WebUI
  - Fixed issues with VoLTE status and 5G network type display

RUTM_R_00.07.06 | 2023.12.20

New
- Network
  - Enabled IPv6 by default for mobile interfaces
  - Added operator blacklisting and whitelisting based on mobile country code
  - Added SIM card not inserted event in Events Log
  - Added 802.11v BSS Transition Management and 802.11k Radio Resource Measurement
- Services
  - Added OPC UA Server
  - Added the ability to set port for TACACS+ in PAM service
  - Added switch to enable using root certificate authority for MQTT alarms in Modbus Client services
  - Added new alarm action "Ubus event" in Modbus Client services
  - Added new input "Modbus alarms" in Data to Server service
  - Added wget ping subtype support in Events Reporting service
  - Added new I/O SNMP OID that returns numeric I/O state
  - Added new Post/Get service action "mobile_sim_pin" for changing used SIM PIN code on the device
  - Added TLS support for OverIP serial functionality
- WebUI
  - Added Tailscale VPN support
  - Renewed user interface design
  - Added network interface name change functionality
  - Added last resort configuration option for multiwan policy rules
  - Added indication when new modem firmware is available
  - Added mobile connection establishment display in mobile status page
  - Added default value for "Reset threshold" field in Low Signal Reconnect feature
- System
  - Added ability to enable/disable SSH access for specific users in System Users
  - API support
Improvements
- Network
  - Disabled operator scan when SIM card is not inserted
  - Added two radio support on one SSID in Wireless
- Services
  - Expanded GRE VPN keep alive functionality to disable routes from unreachable tunnel
  - Added PKCS#12 certificate container authentication method in IPsec VPN
  - Added TLV message_payload support for SNMP service
  - Added Purple.ai configuration profile
  - Replaced option "No leading zeros" with "Remove all zeros" in Over IP serial functionality
  - Added possibility to assign mobile interface in SQM service
  - Added reboot on storage device disappearance and re-appearance
  - Added additional anonymous phone number validation in Mobile Utilities service
  - Added "N/A" signal strength response in DNP3 service if SIM card is not inserted
- WebUI
  - Improved Events Log page loading by adding asynchronous pagination
  - Removed requirement for Diffie-Hellman parameters in OpenVPN service
  - Added improvements for creating OpenVPN IPv6 configurations
  - Added auto redirect after changing router's IP address or port
  - Added "Interface" dropdown for interfaces selection in Wake on LAN service
  - Increased Data to Server service MQTT topic length limit to 65535 characters
  - Added OSPF external routes section to Status page
  - Moved device menu entry “Reboot” to header menu
  - Added indication in Overview, Status -> Mobile and WAN pages when mobile data limit is reached
  - Updated Operator state field to show if modem is in limited service
  - Combined Mobile Usage day, week, month and total pages into one
  - Updated Realtime data -> Mobile signal page design to show all available modems and their bands data in one graph
  - Added message when SIM card requires PIN/PUK code in Status -> Mobile page
  - Moved WiFi scanner page to Services section
- System
  - Added Mosquitto CVE patch 2023-28366
  - Added Mosquitto CVE patch 2023-3592
  - Updated mt76 package version to 2022-12-22
  - Updated hostapd version to 2023-09-08
  - Updated cURL version to 8.4.0
  - Updated kernel version to 5.10.199
  - Updated Mac80211 version to 6.1.24
  - Added RMS data display to generated troubleshoot
  - Added downloaded Package Manager packages list to generated troubleshoot
  - Added process activity load list to generated troubleshoot
  - Changed default OPKG feed to use Teltonika's URL
Fix
- Network
  - Fixed DMVPN firewall rule creation issues
  - Fixed Failover missing active rules when using multiple source and destination IP addresses
  - Fixed mobile service crash due to buffer overflow while reading partially overwritten SMS
  - Fixed an issue with Manual APN connection making attempts too rapidly
  - Fixed deny data roaming functionality when transitioning between roaming and home operator network
  - Fixed network disconnection on mobile network detach and DHCP lease loss situations
  - Fixed VoLTE configuration after modem reboot
  - Fixed Mobile interface bridge and passthrough mode connectivity loss
  - Fixed an issue where rarely PIN code would get removed after SIM switch
  - Fixed mobile operator list being not updated after changes in WebUI
  - Fixed issue where mobile interface was unreachable after device reboot or interface restart while using Failover service
  - Fixed low Wireless mesh throughput
  - Fixed concurrent Wireless STA and AP functionality on 5 GHz band
- Services
  - Fixed SSH module enable in PAM service
  - Added minimum free space check when saving logs to flash in Logging service
  - Fixed "Set multiple coils" function sending too many bytes in Modbus Client services
  - Fixed multiple Events Reporting messages being sent when Firewall configuration is changed
  - Fixed VRRP instances advertising wrong virtual IPs
  - Added Hotspot information in SNMP MIB file
  - Fixed registered Hotspot Local Users showing random username
  - Fixed selection of MAC Auth for LAN interfaces in Hotspot service
  - Fixed inconsistent Hotspot login behaviour when using MAC Auth with Password
  - Fixed instance shutdown after last local user deletion
  - Fixed Cumulocity app not sending any telemetry data
  - Fixed Call Utilities failure when caller id is hidden during a call
  - Fixed AVL with poor mobile connections
  - Fixed default profile SMS Utilities I/O status rule configuration in Profiles functionality
  - Fixed serial timeout not working in Over IP serial functionality
  - Removed "Echo" option in Modbus TCP over Serial functionality
  - Fixed CRC verification failing when CRC is correct in Modbus TCP over Serial functionality
  - Fixed crash when getting unexpected messages from RTU in Modbus TCP over Serial functionality
  - Fixed mobile cell ID retrieval in TR-069 service
- WebUI
  - Fixed side menu style issues when Japanese language is used
  - Fixed displaying of vendor names in Topology page
  - Fixed language packs being selectable when still in Package Manager queue
  - Added ability to configure IPv6 BGP peer
  - Fixed RelayD configuration issues after keep settings
  - Fixed realtime graphs responsive design issues
  - Fixed Network Shares users deletion
  - Fixed not all LAN interfaces shown in dropdown in Hotspot service page
  - Fixed modem updater legacy firmware flashing
  - Fixed wireless realtime data to show signal as unavailable with no connected clients
  - Fixed WiFi scanner disconnecting AP users
  - Fixed setup wizard errors in Wireless configuration page
- System
  - Patched FRR CVE-2023-38406
  - Patched FRR CVE-2023-38407
  - Patched FRR CVE-2023-41358
  - Patched FRR CVE-2023-41360
  - Patched FRR CVE-2023-41909
  - Patched FRR CVE-2023-47234
  - Patched FRR CVE-2023-47235
  - Patched OpenSSL CVE-2023-3446
  - Patched OpenSSL CVE-2023-3817
  - Patched LibXML2 CVE-2023-39615
  - Patched LibXML2 CVE-2023-45322
  - Patched FFMPEG CVE-2021-28429
  - Patched FFMPEG CVE-2022-48434
  - Patched dnsmasq CVE-2023-28450
  - Fixed running out of space when SSHFS is mounted in /tmp while generating troubleshoot

RUTM_R_00.07.05.4 | 2023.11.09

Improvements
- WebUI
  - Improved asynchronous pagination in events log pages
  - Optimized Overview page load
  - Added resource loading cancellation after switching to different page

RUTM_R_00.07.05 | 2023.10.09

New
- System
  - Initial firmware release