TRB140 Firmware Downloads

---

Important:

If you are using FW version TRB140X_R_00.01.06.1 or older on your TRB140 gateway, you will need to follow these instructions in order to successfully upgrade your device's FW to a later version.

---

This page contains firmware files for TRB140 devices. Look to the table below or the changelog to find download links.

To upgrade firmware using WebUI, follow the instructions in TRB140 Firmware.

TRB140

---

File	Type	Release date	Size	MD5	Changelog
TRB1_R_00.07.10.2_WEBUI.bin	Latest FW	2024.11.04	16.1 MB	f26b6859b3c813922c9a06c4148934cc	Link
TRB1_R_00.07.09.4_WEBUI.bin	Mass production FW	2024.10.02	15.92 MB	56e4246ad2745ff1de2aa028f5a14f7e	Link

TRB1_R_GPL_00.07.10.2.tar.gz

SDK

2024.11.04

26.92 MB

e311157f06518ab5faa453caaf2ec3c0

Note: packages for Package Manager are independent from firmware and can be downloaded in the Package Downloads page.

FW checksums

---

Checksums for firmware files can be found here.

TRB1_R_00.07.02.7 | 2022.09.12

• Improvements:
  • Improved manual-auto connection mode

• Fixes
  • Fixed AT command for SMS storage usage
  • Fixed CVE-2022-1012 memory leak vulnerability
  • Fixed CVE-2022-37434 kernel vulnerability
  • Fixed interface option reset after VLAN ID change
  • Removed memory leak on port events

Changelog

TRB1_R_00.07.02.6 | 2022.08.24

• Improvements:
  • Added 'home.vodafone.de' APN
  • Improved stability of device information storage

• Fixes:
  • Added SMSC type omitting when empty SMSC number parsed in SMS PDU mode
  • Fixed Serial-symlink dmesg messages
  • Fixed VoLTE management
  • Fixed OpenVPN tls-auth and tls-crypt option names

TRB1_R_00.07.02.5 | 2022.08.12

• Improvements:
  • Updated curl to version 7.83.1
  • Updated firmware validation error messages
  • Added multiple source IP address support to the Port Forwards page
  • Increased custom APN Username & Password field maximum length to 64 symbols
  • Added auto switch to modem's SMS storage when SIM card storage doesn't exist
  • Improved mobile connection status handling

• Fixes:
  • Fixed CVE-2022-32205, CVE-2022-32206, CVE-2022-32207, CVE-2022-32208 curl vulnerabilities
  • Fixed CVE-2022-30065 busybox vulnerability
  • Fixed file upload path traversal
  • Removed Data to Server limit to proccess less than 10 instances
  • Fixed Data to Server 'out of memory' crashes when database is full or has a large amount of data
  • Fixed OpenVPN dev setting logic
  • Fixed OpenVPN updating from legacy issue that caused IPv6 not to work
  • Fixed MAC and leasetime setting for Bridge & Passthrough modes

TRB1_R_00.07.02.4 | 2022.07.20

• Improvements:
  • Added default password change warning message before firmware downgrade
  • Extended time period for device to make connection to operator
  • Reduced the number of modem reboots when changing mobile settings
  • Reduced excessive log output when no SIM card is inserted
  • Added modem restart prevention on modem init
  • Added disable RPLMN option in the SIM section of the SIM card config

• Fixes:
  • Fixed CVE-2022-2068 vulnerability
  • Disabled autoconnect on stop-network call
  • Fixed authorization issue on 2G/3G only service mode

TRB1_R_00.07.02.3 | 2022.06.27

• Improvements:
  • Updated FSTools package to version 2022-05-03
  • Added security headers to web requests
  • Added ping to DNS IPv6 support
  • Added modem reset to default state after device FW upgrade
  • Modem init now checks NVRAM sensitive commands before setting
  • GSM output was made consistent

• Fixes:
  • Fixed CVE-2019-12900 libbz2 vulnerability
  • Fixed behavior of some gsmctl commands
  • Fixed CVE-2022-23303 hostapd vulnerability
  • Fixed CVE-2022-29581 Linux kernel vulnerability
  • Fixed CVE-2022-29458 ncurses vulnerability
  • Fixed CVE-2022-1292 c_rehash script command injection vulnerability
  • Fixed band locking issue
  • Added default VoLTE value
  • Specified IP address family on operator control's ping to DNS feature
  • Fixed possible firmware corruption when flashing via fastboot
  • Fixed VoLTE management issue

TRB1_R_00.07.02.1 | 2022.06.06

• Improvements:
  • Improved GSM related messages in Troubleshoot logs

• Fixes:
  • Fixed IGMP Proxy menu item not appearing after package installation
  • Fixed default mobile network configuration generation
  • Fixed MODBUS write requests and Mobile Utils option setting

TRB1_R_00.07.02 | 2022.05.23

• New features
  • Overview side widget
  • IGMP Proxy
  • Privileged Access Management (PAM)
  • AWS Greengrass support
  • HTTPS certificate and key upload feature
  • SSH public keys edit box
  • License page
  • DNP3 data for Data to Server

• Improvements
  • Updated busybox to version: 1.34.1
  • Updated curl to version 7.79.1
  • Added iptables filter package for string filtering
  • Added CHAP authentication for L2TP VPN
  • Added IPv6 support for L2TPv3 VPN
  • Added EAP-MSCHAPV2 authentication method for IPsec VPN
  • Added IPv6 support to Auto Reboot
  • Added 'Save to flash' and 'Test configuration' button to DNP3 configuration page
  • Updated SNMP version 5.9.1
  • Added OpenSSL authentication options to SNMPv3
  • Added support for OSPF redistribution options and OSPF neighbors
  • Added password field to BGP Peers page
  • Extended BGP "AS" field validation to accept integers up to 4294967295
  • Added "DHE+RSA" to OpenVPN cipher selections
  • Increased OpenVPN max password length from 128 bytes to 512 bytes
  • Made HMAC key direction initial value dependent on the role of the instance (client or server)
  • Made HMAC key and HMAC authentication key upload fields required
  • Added DES to IPsec encryption algorithms selections
  • Added special character support for CHAP secrets
  • Added validation requirements for PPTP user list username field
  • Added option to manually enter Public key in Wireguard configuration
  • Made generating Wireguard keys possible only while in auto mode
  • Added Events Log database to troubleshoot archive
  • Added RFC1918 filter field
  • Added the possibility to unblock multiple blocked devices at once
  • Added 'Port' column to blocked login attempts table
  • Added Speedtest server refresh
  • Updated Speedtest server list
  • Added asterisk option to Site Blocking
  • Added MD5 and SHA256 checksums to package validation page
  • Changed certificate requirements to only require client key file if client certificate is used
  • Added pagination and data retention between table pages
  • Added pagination functionality to tables when there are more than 10 records
  • Improved table sorting by saving user provided sort settings in the browser
  • Improved drag and drop functionality
  • Added the possibility to drag and drop files onto upload components
  • Moved 'Root CA' from the 'Access Control' page to the 'Certificates' page
  • Added 'Strict-Transport-Security' response header for HTTPS
  • Added 'breadcrumbs' to modal windows
  • Improved initial WebUI loading after login
  • Added mobile bytes sent and bytes received SNMP OIDs
  • Added mobile LED turn off feature ('System -> Administration' page)
  • Added 'iot.1nce.net', 'internet', 'VZWINTERNET' and Truphone APNs to APN database
  • Updated mobile usage data point calculation logic
  • Added the possibility to manually enter operator number
  • Improved obtain mobile cell ID process
  • Added modem restart if SIM card is removed during APN database fetching process
  • Added unauthorized call logging
  • Added space character support in SMS commands
  • Disabled SMS modem storage configuration form when SIM is not inserted
  • Changed SMS '%wi' parameter value to return IP address of any currently used WAN interface (not only wired)
  • Added external modem SMS limit Overview card and widget
  • Made in-use APNs visible next to mobile interface configurations (before clicking the 'Edit' button)
  • Added duplicate value check for list configuration options
  • Changed mobile card instance design
  • Fixed 'Mobile Data usage reset' SMS rule
  • Fixed the default state parameter of SMS list POST/GET command
  • Added I/O SNMP trap
  • Added ISO 8601 time format to I/O Juggler's '%ts' parameter
  • Added device name parameter '%pc' to I/O Juggler
  • Added PPPoE VLAN priority support
  • Made VRRP ping section dependent on main instance

• Fixes
  • Fixed CVE-2021-20322, CVE-2021-4197, CVE-2022-1011, CVE-2022-0847 kernel vulnerabilities
  • Fixed CVE-2022-28391 busybox vulnerability
  • Fixed CVE-2018-16789 shellinabox vulnerability
  • Fixed CVE-2021-44543, CVE-2021-44542 privoxy vulnerabilities
  • Fixed CVE-2021-43618 GNU Multiple Precision Arithmetic Library vulnerability
  • Fixed zlib backport security issue
  • Fixed Wireguard firewall zone assignment
  • Fixed queued packages disappearing from list after FW upgrade with keep settings
  • Fixed error message display for multiple input validation rules
  • Fixed incorrect DHCP validation range for start and limit fields
  • Removed 'Bring up on boot' option from network interface configuration pages
  • Fixed coma-separated DHCP options disappearing after save
  • Fixed exclude and listen interfaces
  • Fixed 'Use broadcast flag' option saving
  • Fixed firewall zone assignment when creating new interfaces
  • Fixed OpenVPN 'Netmask' and 'IP address' field validations
  • Fixed OpenVPN TAP configuration saving issue
  • Fixed OpenVPN switching to TUN mode when uploading a configuration from file
  • Fixed dynamic BGP route state display
  • Fixed BGP peer enable in edit page
  • Fixed issue when no L2TP client instance could be bound to IPsec
  • Fixed firewall rule and zone behavior related to config section creation
  • Added default value for L2TPv3 netmask, which is now written to config after save
  • Fixed passthrough option saving to IPsec file
  • Fixed DMVPN issue where instance configuration could not be saved
  • Fixed Wireguard peer could not be saved issue
  • Fixed NTP client time synchronization after factory reset
  • Fixed device time display with selected time zone
  • Fixed MODBUS TCP indexation missing bracket issue
  • Fixed initial MODBUS TCP request count validation
  • Fixed PIN 3/4 direction switching over MODBUS TCP
  • Fixed MODBUS data to MQTT socket closing issue when connection fails
  • Fixed MODBUS alarm configuration deletion
  • Fixed DNP3 master not working after FW upgrade with 'keep settings'
  • Fixed DNP outstation not returning error messages
  • Added missing SNMP objects: mobile IP, data sent/received today
  • Fixed MQTT Publisher 'Remote address' field validation
  • Fixed long interface name support for Azure IoT Hub
  • Increased maximum Azure IoT Hub 'Connection String' length to 4096 characters
  • Fixed missing sent/received data issue
  • Fixed URL input field length validation
  • Fixed admin login issue after upload of backup from a device with older firmware versions
  • Fixed MAC address formatting in Events reporting messages
  • Fixed Events reporting DHCP lease message spam, when no new lease is added
  • Fixed logging crashing after downloading Troubleshoot file
  • Made Wake on LAN visible only on devices with Ethernet ports
  • Fixed Traffic log file transfer to FTP server
  • Fixed Web Filter service reloading after a host list file is uploaded
  • Fixed access denied messages when sending JSON-RPC requests from root user
  • Fixed error message display about duplicated intervals in Profile scheduler
  • Fixed FW upgrade with 'keep settings' migration issue for Access Control's 'Fail count' and 'Device port' fields
  • Corrected OSPF Routing card values, value positions and names
  • Fixed global secret instances not being removed when there are no IPsec instances
  • Fixed uploaded file remove icon not staying in position on hover
  • Fixed Overview card collapse issue that made it unresponsive after too many clicks
  • Removed WAN6 interface from the Overview page
  • Fixed mobile IPv6 display in Events Reporting status messages
  • Fixed Bridge mode when DNS2 is not available
  • Fixed PAP/CHAP username and password fields not saving in interface edit window
  • Fixed sending email without secure connection for providers that support such an option
  • Fixed 'N/A' parameter showing up in SMS Utilities monitoring status message
  • Fixed Call Utilities Events Log message for reboot rule
  • Fixed SMS command validation for no-authorization option
  • Fixed MODBUS SMS alarms 'Enable' option saving
  • Fixed running RMS with no SIM card inserted issue
  • Fixed firmware available on server version checking issue
  • Fixed CVE-2020-15078 openvpn vulnerability
  • Fixed storage calculation for packages
  • SMS Utilities: enhanced service security
  • Fixed firmware deletion after leaving the page
  • Fixed setup wizard redirect after LAN IP change
  • Fixed various validation bugs, typos, option hints & alignments
  • Fixed multiple IPv6 configuration field validations
  • Fixed relay output value display in I/O Juggler condition page
  • Fixed I/O Juggler's WiFi rule not enabling or disabling WiFi interfaces
  • Fixed I/O Juggler's double delete issue on I/O Juggler action and condition instances
  • Fixed I/O Juggler's incorrect I/O status messages

TRB1_R_00.07.01.4 | 2022.02.25

• Improvements
  • Increased Port Forwards rule max name length
  • Added a new '%it' parameter for UTC time in ISO 8601 format to I/O Juggler

• Fixes
  • Added missing bracket to the end of MODBUS messages
  • Fixed preserving the contents of /etc/luci-uploads/ after FW upgrade with the 'Keep all settings' option
  • Fixed IPv4-Gateway column showing empty values in the Status -> Routes page
  • Fixed firewall extra option validation
  • Fixed usage of custom headers in I/O Juggler HTTP action
  • Fixed 'verify' option parsing for I/O Juggler
  • Changed the logic of uploading files to the modem
  • Fixed OpenVPN server configuration with password authentication
  • Fixed NTP interval length validation
  • Fixed network interface enable after Drag & Drop
  • Updated NTP client interval to 24h
  • Fixed connection to whitelist carriers
  • Fixed Passthrough mode when DHCP is disabled
  • Fixed 'Deny data roaming' feature
  • Fixed mobile blocking dependency on region
  • Disabled Ping To DNS functionality when Bridge/Passthrough mode is enabled

TRB1_R_00.07.01.2 | 2022.01.04

• New features
  • DFOTA modem upgrade system for Quectel modems

• Improvements
  • Removed L2TP section title prefixes

• Fixes
  • Fixed IPSec crashing issue using mobile
  • Fixed FW flashing when chip is in unknown state
  • Fixed CPU usage percentage display in the Overview page
  • Fixed FOTA timeout issue when server does not respond
  • Fixed installation of backup packages
  • Fixed mobile data limit display after profile change
  • Fixed Bridge mode without multi-APN
  • Fixed multi mobile interface checking
  • Fixed error handling when the modem is not responding
  • Prolonged autoconnect setting timeout

TRB1_R_00.07.01 | 2021.11.18

Note: Firmware version TRB1_R_00.07.01 released on 2021.11.18 was removed due to an issue with IPsec tunnel while using mobile connection.

---

• New features
  • Tinc VPN
  • German language support
  • Manual-Auto operator select

• Improvements
  • Updated base to OpenWrt version 21.02
  • Improved WebUI functionality when multiple browser tabs are open
  • Updated mtd-utils to version 2.1.2
  • Updated busybox to version 1.33.1
  • Updated ubus to version 2021-06-3
  • Updated ubox to version 2020-10-25
  • Updated rpcd to version 2021-03-11
  • Updated opkg to version 2021-06-13
  • Updated fstools to version 2021-01-04
  • Updated wwan to version 2019-04-29
  • Updated ethtool to version 5.10
  • Updated uhttpd to version 2021-03-21
  • Updated ppp to version 2020-10-03
  • Updated odhcpd to version 2021-07-18
  • Updated hostapd to version 2020-06-08
  • Updated dropbear to version 2020.81
  • Updated dnsmasq to version 2.85
  • Updated netifd to version 2021-07-26
  • Updated firewall3 to version 2021-03-23
  • Updated libjson-c to version 0.15
  • Updated libevent2 to version 2.1.12
  • Updated mac80211 to version 5.10.42-1
  • Updated wireless-regdb to version 2021.04.21
  • Updated binutils to version 2.35.1
  • Updated gdb to version 10.1
  • Updated strace to version 5.10
  • Updated trace-cmd to version 2.9.1
  • Updated valgrind to version 3.16.1
  • Updated ath10k-ct-firmware to version 2020-11-08
  • Updated procd to version 2021-02-23
  • Updated iw to version 5.9.8
  • Updated iproute2 to version 5.11.0
  • Updated iptables to version 1.8.7
  • Updated nettle to version 3.6
  • Updated libpcap to version 1.9.1 rel3
  • Updated elfutils to version 0.180
  • Updated cryptodev-linux to version 1.11
  • Updated linux-firmware to version 20201118
  • Updated util-linux to version 2.36.1
  • Updated openwrt-keyring to version 2021-02-20
  • Updated mtd to version rel26
  • Updated fwtool to version 2019-11-12
  • Updated ca-certificates to version 20210119
  • Updated wireguard-tools to version 1.0.20210223
  • Updated iwinfo to version 2021-04-30
  • Updated ipset to version 7.6
  • Updated gre to version rel12
  • Updated wolfssl to version 4.7.0
  • Updated ustream-ssl to version 2020-12-10
  • Updated uclient to version 2021-05-14
  • Updated readline to version 8.1
  • Updated mbedtls to version 2.16.11
  • Updated libusb to version 1.0.24
  • Updated libunwind to version 1.5.0
  • Updated libubox to version 2021-05-16
  • Updated libnl-tiny to version 2020-08-05
  • Updated libnftnl to version 1.1.8
  • Updated libiconf-full to version 1.16
  • Updated libbsd to version 0.10.0
  • Updated gmp to version 6.2.1
  • Updated ulogd to version rel6
  • Updated sqm-scripts to version 1.5.0
  • Updated ntpclient to version rel14
  • Updated nmap to version 7.80
  • Updated curl to version 7.77.0
  • Updated zerotier to version 1.6.5
  • Updated xtables-addons to version 3.13
  • Updated xl2tpd to version 1.3.16
  • Updated stunnel to version 5.59
  • Updated strongswan to version 1.0.13
  • Updated sstp-client to version 1.0.13
  • Updated pptpd to version rel5
  • Updated openvpn to version 2.5.3 rel2
  • Updated ntpd to version rel3
  • Updated net-snmp to version rel2
  • Updated mosquitto to version 2.0.11
  • Updated miniupnpd to version 2.2.1 rel 3
  • Updated etherwake to version rel5
  • Updated libzip to version 1.7.3
  • Updated libgpg-error to version 1.39
  • Updated glib2 to version 2.66.4
  • Updated libnetfilter-conntrack to version 1.0.8
  • Updated libnetfilter-log to version rel3
  • Updated lzo to version rel4
  • Updated nghttp2 to version 1.43.0
  • Updated openvpn-easy-rsa to version 3.0.8 rel3
  • Updated iperf to version rel2
  • Updated iperf3 to version 3.10.1
  • Updated e2fsprogs to version 1.45.6
  • Updated fuse to version 2.9.9
  • Updated udprelay to version 2020-02-26
  • Updated qmicli to version 1.28.2
  • Updated pcre to version 8.45
  • Updated libsmpp34 to version 1.14.1
  • Updated libiwinfo to version 2.1
  • Added netifd library for additional information related to network interfaces
  • Updated openssl to version 1.1.1l
  • Updated privoxy to version 3.0.32
  • Added ACL reload method for sessions
  • Added 'Advertisement interval' field to the VRRP configuration window
  • Added a PPTP-to-WAN Zone Forwarding rule when default route is enabled on PPTP client
  • Added email user group validation for sendind test emails with Events reporting
  • Added an event logging feature for Ping Reboot events
  • Improved file/section deletion logic: now files are also deleted after deleting a related config section
  • Improved package deletion logic
  • Added the possibility to configure multiple reboot times in one Reboot Scheduler configuration instance
  • Updated 'External system log server' field validation to accept IPv6 addresses
  • Added redirect to Overview page after login
  • Added WebUI session timeout after user inactivity
  • Added placeholder text to dropdown menus
  • Improved multi-select design and functionality
  • Added Unix timestamp, local ISO time, UTC time to Modbus
  • Added info message when selected file cannot be uploaded
  • Improved IPsec throughtput
  • Added IPSec "Compatibility mode" configuration support
  • Made SNMP 'Community name' option editable
  • Added the option to delete configurations to the SMS Utilities 'UCI' rule
  • Added 'hour', 'week day', 'month day' slelection options to SMS Limit configuration
  • Added Lithuanian and Verizon APNs
  • Added modem selection for the 'Send SMS' option in Auto Reboot settings
  • Added the possibility to get total data usage value without specifying time interval via ubus
  • Added I/O support to SNMP
  • Removed ubus list method due to security reasons
  • Added MODBUS "%I, %T, %S, %r, %n" support to MODBUS Data Sender
  • Removed search engine site crawling
  • Improved IPSec "Local/Remote source" validation
  • Added Firewall "all" and "custom" protocol options
  • Added Backup file size limit of 2 MB
  • Improved basic/advanced mode changing
  • Improved Wireguard "IP Addresses" field validation
  • Added language download support from language selection section
  • Added PPTP "Client to client" configuration support
  • Made DDNS "username", "password", "host" fields optional
  • Added SSTP "Default route" configuration support
  • Added SMS Limit hour, week day and month day support
  • Added Passthrough "Leasetime" and "Unit" configuration support
  • Added Call Utilities "Active Timeout" configuration support

• Fixes
  • Made RMS 'Connect' button disabled when a connection attempt is already in progress
  • Added validation for TLS Clients 'Private network' option
  • Fixed the validation range for MTU fields
  • Fixed removing firmware image file after leaving the fimware upgrade page
  • Fixed network selection list for Traffic Logging - added all available LAN networks
  • Fixed DHCP Options validation
  • Fixed configuration profile date display
  • Fixed blank page after invalid URL in login page
  • Fixed TR-069 related firewall rule loading
  • Fixed remote subnet netmask validation issues for the GRE Tunnel configuration
  • Fixed WebUI section toggle
  • Fixed package installation modal layout
  • Fixed current page values showing up in login page username field
  • Fixed the possibility to create section with a name that is already in use in the same config file
  • Fixed OpenVPN username and password deletion when deleting configuration instance
  • Fixed session closing issue for the user whose password was just changed
  • Updated MODBUS credential validation
  • Updated MQTT credential validation
  • Fixed DNS 'Rebind protection' setting when switch is disabled
  • Updated libgcrypt to version 1.9.3 to fix CVE-2021-33560
  • Fixed CVE-2021-33624, CVE-2021-29648 vulnerabilities
  • Fixed DHCP 'Lease time' and 'Unit' option saving over the Setup Wizard LAN page
  • Fixed Reboot Scheduler not removing crontab file after disabling the rule
  • Fixed OpenVPN 'Extra options' field validation to allow a space character
  • Added table drag and drop functionality to the Firewall's Traffic Rules page
  • Fixed DNP3 Outstation crash caused by non-void function returning no value
  • Fixed RMS 'Copy' button functionality
  • Fixed gsmd deamon crashing after modem restart
  • Fixed gsm memory leak
  • Fixed WCDMA band names for MEIG modules
  • Fixed SMS Gateway loading screen issue when sending an SMS message
  • Fixed mobile data database error after upgrading firmware with the 'Keep settings' option
  • Fixed rpcd memory leak issue
  • Fixed network information gathering
  • Fixed 3G LED not being active in 3G mode
  • Fixed data limit accuracy issue
  • Fixed I/O Juggler hour condition interval issue
  • Removed 'Memory Expansion' and 'Printer Server' from the Status -> Services page
  • Patched CVE-2021-40528 vulnerability
  • Patched CVE-2021-40490 vulnerability
  • Patched CVE-2020-16120 vulnerability
  • Fixed VLAN section creation
  • Returned Interfaces "Port priority" option
  • Fixed missing Content-Type header to initial WebUI response
  • Fixed RIP information parsing in status page
  • Fixed OpenVPN IPv6 netmask validation
  • Fixed SNMP Trap Settings Host/IP field validation
  • Fixed Cumulocity authentication reset
  • Fixed Events Reporting rule saving

TRB1_R_00.07.00.1 | 2021.09.02

• Fixes:
  • Fixed reboot on MBN configuration reload

TRB1_R_00.07.00 | 2021.07.16

• New features
  • New WebUI based on Vue.js 2.6.12
  • RutOS updated to OpenWrt 19.07.7 base
  • DNP3 Master and DNP3 Oustation
  • 'Restore to user's defaults' SMS Utilities rule
  • 8021q VLAN support
  • DHCP Relay AT command
  • Enabled user-space watchdog

• Improvements
  • Updated firewall to release 3
  • Updated kernel to version 4.14.221
  • Updated uhttpd to version 2020-10-01
  • Updated xtables-addons to release 9
  • Updated mwan to version 2.8.14
  • Updated pcre to version 8.44
  • Updated curl to version 7.74
  • Updated sqlite to version 3.33
  • Updated ncurses to version 6.2
  • Updated OpenSSL to version 1.1.1k
  • Added full MODBUS register address expansion specifier for Data to Server
  • Added full MODBUS register address legend
  • Added Client ID option for the MQTT protocol in Data to Server
  • Improved Data to Server sleeping accuracy
  • Improved Data to Server username validation; now space is allowed
  • Added firmware version OID to the SNMP service
  • Added IP address family option field to the SNMP page
  • Added SNMPv6 section to the SNMP Communities page
  • Renamed the 'System -> Users' page to 'System -> System Users'
  • Moved password changing option to the 'System -> System Users' page
  • Switched to ar8216 driver
  • Added IPsec XAUTH support
  • Improved OpenVPN updown, init scripts to write info about instance in JSON
  • Added AES-256-GCM encryption support to OpenVPN
  • Added extra configuration parameters to DMVPN
  • Added PSK conversion to DMVPN and single PSK types
  • Improved Package Manager package installation, deletion and dependencies
  • Improved Package Manager download process over FOTA
  • Added new Input/Output values manageable over RMS
  • Added IPv6 traffic logging
  • Made 'Network -> Failover' and 'Network -> Interfaces' page data draggable on multiple browsers
  • Added Input/Output Post/Get URL parameter t_time changing delay and time to seconds or miliseconds
  • Added message storage management by config value
  • Improved QMI error handling and status tracking
  • Turned on modem in preinit for correct power-on sequence
  • Added Post/Get feature to turn mobile data on/off
  • Added the possibility to use 2gonly/3gonly/4gonly arguments for cellular service command alongside current 2g/3g/lte arguments
  • Added "Phone number" and "Message" fields for "Send SMS" option
  • Excluded MAC address from Configuration Backup files

• Fixes
  • Added glib2 patch to fix CVE-2019-13012 vulnerability
  • Added ntfs-3g patch to fix CVE-2019-9755 vulnerability
  • Added WolfSSL patch to fix CVE-2021-3336 vulnerability
  • Added Busybox patch to fix CVE-2018-1000500 vulnerability
  • Added netifd, odhcp6c IPv6 routing loop on point-to-point links patches to fix CVE-2021-22161 vulnerability
  • Fixed Android clients IPsec MTU/MSS size
  • Fixed wrong IPsec DPD value saving
  • Changed IPsec PSK maximum length to 128 symbols
  • Fixed SSTP remaining up after package removal
  • Fixed DMVPN crypto_proposal write to config
  • Fixed I/O Juggler's SMS sending to correct group
  • Fixed I/O Scheduler's relay state issue
  • Added I/O direction check while changing IOs via I/O Post/Get
  • Fixed float endianness mismatch on some devices MODBUS TCP Master, MODBUS Serial Master
  • Fixed UPnP issue that caused config changes to apply only after service restart
  • Fixed WebUI files caching when upgrading firmware
  • Fixed WebUI date display format
  • Fixed MODBUS returning incomplete MAC address data
  • Fixed depleting IPv6 RA timeout when the ISP doesn't send RA updates
  • Added "Transaction timed out" error handling
  • Fixed PPPOE connection loss when wrong session PADT packet arrives
  • Added gcont object tracking and info update if this service is restarted
  • Fixed default SMS storage
  • Fixed SMS warning sending after Mobile Data Limit change
  • Fixed DHCP relaying over mobile networks
  • Changed PIN code maximum length to 8 symbols
  • Fixed 'I/O status' message to include correct Input/Output name based on info in ubus ioman objects

TRB1_R_00.02.06.1 | 2021.02.10

• Fixes
  • Added dnsmasq patch CVE-2020-25681, CVE-2020-25682, CVE-2020-25683, CVE-2020-25684, CVE-2020-25685, CVE-2020-25686, CVE-2020-25687
  • Fixed bootloop which sometimes occurred when no SIM card is inserted
  • Fixed SSH reachable over SIM IP in early boot
  • Fixed modem status after failed network scan
  • Fixed mbncfg function and PIN check logic
  • Fixed PPTP server interface naming
  • Fixed correct client PPTP interface name selection for route creation
  • Fixed adding helper to firewall's wan zone when enabling PPTP configuration
  • Added package size checking when manually installing a package
  • Fixed 'New Firmware Available' message display after firmware upgrade

TRB1_R_00.02.06 | 2020.12.31

• New features
  • Operator Whitelist/Blacklist
  • i2c-tools & spi-tools packages (possibility to control I/O pins on the PCB of the device)
  • Web Filter
  • Interface Based VLAN

• Improvements
  • Updated base to OpenWrt 19.07.4
  • Added Phone Groups as possible SMS recipients to SMS Post/Get
  • Added PSK support for MQTT Broker/Publisher
  • Changed Output Scheduler structure
  • Removed limitation of one configuration per Input
  • Added multiple modem support for TR-069
  • Fixed parsing user uploaded custom OpenVPN configuration files containing carriage returns
  • Added iptables conntrack flush on WAN Failover if IPsec is enabled
  • Optimized package responsible for sending/receiving GRE Tunnel keepalive packets
  • Added extra error checking to Package Manager when downloading packages
  • Added data usage info for both SIM cards to RMS
  • Added logging to syslog when Ping/Wget Reboot "Action" is set to 'None'
  • Improved display of configuration tables when a lot of information is shown
  • Renamed MODBUS strings to uppercase
  • Added redirect to configuration page after a new configuration is created with the 'Add' button
  • Added option to create a Configuration Profile from current configuration
  • Added data validation to Profiles Scheduler fields
  • Replaced the Firewall 'Helpers' page with conntrack helper configuration for each firewall zone
  • Increased dynamic list maximum amount of values to 50
  • Added the possibility to save email accounts without entering email username and password
  • Unified device access password validations
  • Expanded DDNS validation for domain input to accept emails
  • Added SMS Utilities rule to reset mobile data usage for specified interface
  • Improved SMS Utilities VPN status rule to support custom configurations
  • Added SMS storage limit check after inserting a SIM card
  • Changed modem name from primary to internal if device has only one built-in modem
  • Improved SIM count check during init
  • Added MTU option to 'Mobile' protocol configuration

• Fixes
  • Fixed IPsec Passthrough subnet/ip value parsing to make it dynamic for leftsubnet
  • Fixed occasions when error messages overlap buttons
  • Fixed I/O state saving after revert back to original state
  • Fixed IPsec connection after reboot
  • Fixed bridged interface configuration for L2TPv3
  • Removed trailing newlines in returned SNMP strings
  • Fixed Events Reporting waiting to send email before rebooting
  • Fixed MQTT MODBUS Gateway not working when topics have special characters
  • Swapped pin3 and pin4 values in MQTT Publisher
  • Added an 'IP4Table' option to advanced interface configuration
  • Fixed an issue where User Scripts were being deleted after device reboot
  • Fixed various WebUI validation bugs, typos, option hints & alignments
  • Fixed a bug that caused an internal sever error after logging in with a username that contained special characters
  • Fixed crashes that occur after configuration files are not correctly generated
  • Fixed a Firewall Port Forwarding bug which caused an internal sever error when no 'Protocol' was selected
  • Fixed changing WebUI mode bug while current page is accessed with POST method
  • Fixed password allowed lengths and tooltips
  • Fixed mountpoint display
  • Removed non-supported SMS Utilities rules
  • Fixed SMS sending to Phone Group on I/O event
  • Changed device name in 'Status' message to configured name instead of the default one
  • Added modem reinit after SIM card initialization failure
  • Fixed SMS Limit checking when messages exceed the set SMS limit
  • Moved 2-8 PDP contexts to 9-16 the 2-8 are necessary for SIM card MIB APNs
  • Changed mobile interface subnet to /32
  • Fixed modem SIM card checking
  • Fixed multi SMS handling on SMS Limit
  • Fixed Call Utilities multiple SMS sending per received call
  • Fixed SMS storage limit check on device reboot
  • Changed SNMP mSignal, mTemperature and numSatellities datatypes to correspond to devices' MIB files
  • Fixed device Internet access issue when device is in mobile Passthrough mode
  • Fixed access to device via USB when OpenVPN TAP is on
  • Fixed serial over IP Bidirect mode issues
  • Fixed MBNCFG list handler

TRB1_R_00.02.05.2 | 2020.11.19

• Fixes
  • Randomized the global rate limiter to mitigate "SAD DNS" attack

TRB1_R_00.02.05.1 | 2020.09.30

• New features
  • DLNA media server
  • iptables NETMAP extension
  • "Flush connections on" option for WAN Failover
  • New firmware notifications
  • Updated header logo from 'Teltonika' to 'Teltonika | Networks'
  • USSD command support
  • Time sync via network operator's station

• Improvements
  • Improved WebUI page loading speed
  • Added Basic/Advanced mode selection in Setup Wizard
  • Added a dropdown with a search function for time zone selection
  • Added "copy to clipboard" button in Cloud Solutions next to MAC and Serial
  • Added option to send all Modbus records in one packet
  • Disabled IPV6 services on LAN by default
  • Added password hashing in Post/Get pages
  • Added a warning message about rebooting the device while certificate files are being generated
  • Added status option to uploaded custom OpenVPN configuration file
  • No longer showing "Enable OpenVPN config from file" option if "Enable external Services" is selected
  • Added some missing placeholder values
  • Added warning message about unsaved changes when leaving Auto Reboot, Periodic Reboot, Wireless pages
  • Added port selection to SSTP configuration
  • Changed Periodic Reboot service name to Reboot Scheduler
  • Added table row highlights on hover
  • Changed section name from 'Email users' to 'Email accounts' in the Recipients page
  • Added network interface automatic assignment to firewall zones when interface protocol is switched
  • Adjusted Azure validations
  • Adjusted Local/Remote subnet field validations
  • Adjusted Hotspot field validations
  • Unified VPN overview section option names and titles
  • Removed mandatory requirements for inter-zone forwarding source & destination options in Firewall zone configuration
  • Added placeholder values for drop down options in Routing pages
  • Increased maximum package upload size
  • Removed mobile interfaces from Hotspot configuration
  • Added "Passthrough subnets" option to IPsec configuration page
  • Added package size checking when installing packages via Package Manager
  • Optimized switching between Basic and Advanced WebUI modes
  • Added missing services to Events Reporting page when selected Event is "Config change"
  • Improved general web design, ordering and positioning
  • Added word wrap in the Unsaved Changes page
  • Centered 'Apply' button in the Profiles page
  • Hid network interfaces with DHCPv6 protocol in Overview page while in Basic WebUI mode
  • Changed tcpdump "Select storage" option value from 'Internal storage' to 'RAM memory' in the System → Administration → Troubleshoot page
  • Added more descriptive error messages when connection to FOTA server fails
  • Updated "Local address" hint in l2tpv3 page
  • Updated phone number placeholders to +37000000000
  • Updated SMS rule descriptions related to phone numbers and email accounts
  • Made SMS/Mobile data limit options always visible in Overview Setup page
  • Added indications for which antenna connector is connected to which modem
  • Adjusted Modem FW file validations
  • Added network selection option in Traffic logging page

• Fixes
  • Fixed DDNS freeze issues
  • Fixed Firewall Traffic Rules Source and Destination address field validations
  • Started using more stable, builtin ar82xx switch driver
  • Symlinking tty devices in one place
  • Fixed period when sending packet curl timeouts in Modbus Data Sender
  • Fixed "active SIM" register value retrieval after regression in Modbus TCP Slave
  • Fixed Hotspot 'Trial access' function
  • Fixed OpenVPN TLS Cipher display and added a limit to number of ciphers
  • Fixed various WebUI validation bugs, typos & option hints
  • Fixed DHCP lease range validation and value saving in Interfaces page
  • Fixed error messages when creating interfaces with incorrect names
  • Fixed various section toggling bugs
  • Fixed username validation in SNMP page
  • Fixed certificate file importing bugs & common name display in Certificates Manager page
  • Fixed interface option related to IPv4 and IPv6 in Routing pages
  • Fixed OpenVPN multi-line command that adds client specific parameters
  • Fixed DHCP lease range validation in Basic mode
  • Fixed incorrect sorting in dynamic tables
  • Fixed routing table writing and deleting
  • Fixed incorrectly displayed type when no protocol is selected
  • Removed Wireguard interfaces from the Interfaces page
  • Fixed SNMP user access mode display in SNMPV3 Users Overview page
  • Fixed SNMP memory leak on chilli module
  • Fixed MD5 and SHA256 checksum calculations
  • Fixed DHCP-options field validation to allow separating parameters with commas
  • Fixed Package Manager side menu entry updates right after package upload
  • Fixed Wireguard port selection
  • Fixed VPN zone status display
  • Fixed lua errors when Start/End time option is empty
  • Fixed incorrectly displayed OpenVPN protocol
  • Fixed Lua errors in Profile Scheduler and Firewall Zones
  • Removed /log folder from Troubleshoot file directories
  • Fixed endless spinner when applying profiles
  • Fixed nil value in the Traffic Logging page
  • Fixed "Units" option dependency on "Enable DHCP" option in the Setup Wizard's LAN page
  • Fixed redirecting to login page after factory setting restore (reset)
  • Removed Unsaved Changes notification when downloading Troubleshoot/tcpdump files from the System → Administration → Troubleshoot page
  • Vulnerability fixes for Package Manager and Certificates Manager pages
  • Fixed Firewall zone placeholder (removed "-- Please select --" and left "Unspecified")
  • Fixed update from server option in the Firmware page
  • Added missing error messages when password is invalid in default password change page
  • Fixed "Lease time" option in the Setup Wizard's LAN page
  • Fixed error 500 when accessing Advanced pages while in Basic mode
  • Increased allowed character lengths for MQTT Broker and Data to Server
  • Fixed XSS vulnerabilities in package manager and package file upload pages
  • Fixed incorrect OpenVPN configuration saving
  • Fixed NHRP lua error
  • Removed "Wireguard" from Status → Services display if it is not installed
  • Fixed crashing issue when getting "SIM slot in use" satus value
  • Fixed sending status SMS to other number
  • Fixed "Change mobile settings" rule service setting
  • Fixed SMS Forwarding To HTTP "URL" option validation
  • Fixed Mobile Signal graph data display
  • Changed message type from 'error' to 'info' from Auto Reply page
  • Fixed manual operator selection validation
  • Fixed mobile interface authentication settings reset after selecting auto APN mode
  • Fixed libgsm password and serial authorization
  • Added workaround for mobile to switch LAN port throughput problem for ath79 target
  • Fixed Q-in-Q device display in Interface Physical Settings
  • Removed rmnet0 (mobile) from Physical Interface selection options
  • Filtered out rndis0 (usb) interfaces from Network → WAN page
  • Fixed WebUI access denial when upgrading from old FW version
  • Removed Hotspot 2.0 page

TRB14X_R_00.02.04.3 | 2020.07.31

• New features
  • Backup archive MD5 & SHA256 checksum calculation to help user identify altered backup archives
  • Package signature check to verify that a package comes from Teltonika

• Improvements
  • Updated APN database

• Fixes
  • Fixed CVE-2019-17367
  • Fixed hiding of configuration pages that users of a specific group don't have read access to
  • Fixed firmware upload script

TRB14X_R_00.02.04.1 | 2020.07.02

• New features
  • Relay control to Call Utilities
  • 'Certificates' page for generating and managing TLS certificates
  • 'Drag & Drop' support for Overview page tables
  • 'Speed Test' feature
  • AVL I/O support
  • Added JSON formatting option to Data to Server
  • Added timeout and keep-connection options to Modbus TCP Slave
  • During this release a new package was released - WireGuard

• Improvements
  • Improved 'Profile Scheduler' with minute accuracy
  • Reordered VPN configuration options
  • Standardized section header styles
  • Unified spelling of dropdown values
  • Added information about 'Package Manager' packages before updating firmware
  • Updated services management to Status → Services page
  • Improved performance of firmware upgrades from server
  • Improved security features related to file uploading and HTTP headers
  • Changed RAM/flash memory units from MiB to MB
  • Updated warning message and lease deletion message for static leasing
  • Moved 'Country code' option to general tab
  • General web responsiveness improvements

• Fixes
  • Fixed SDK firmware compilation
  • Fixed eth0 interface display
  • Fixed validations and option saving in OSPF page
  • Fixed various element positioning bugs on smaller screens
  • Fixed switching to advanced mode notification when accessing non existing pages
  • Fixed validations in Traffic Logging page
  • Fixed showing failover section only for interfaces with failover rules
  • Fixed static leases redirect after saving
  • Fixed empty dropdown values in 'I/O juggler' and 'Network Shares'
  • Fixed interface IP address validation in DDNS page
  • Fixed various spelling mistakes
  • Fixed broken address option in the 'Troubleshoot' page
  • Fixed dropdown select element double clicking issue
  • Fixed basic/advanced mode switching with Microsoft Edge browser
  • Fixed firmware upgrading bug when LAN interface with a changed name exists
  • Fixed redirecting to the 'Interfaces' page when mode is changed from basic to advanced and user is in the 'LAN' or 'WAN' pages
  • Fixed validation of custom header in 'Data To Server' page
  • Fixed "Type" option error in Failover page
  • Updated username and password validations
  • Fixed profile change action in 'I/O Juggler'
  • Fixed bidirectional GPIO change feature

TRB14X_R_00.02.03.2 | 2020.06.03

• New features
  • Added 'Mobile Passthrough mode'
  • Added mobile signal real-time graph
  • Responsive WebUI design
  • New Access Control window for managing IP access
  • Attack Prevention page under Firewall settings
  • New IPv6 options in WAN, LAN and VPN pages
  • Hotspot Users Management page
  • Progressive Web Application support and extra page caching when device is configured with a valid SSL certificate
  • OpenVPN configuration file upload functionality
  • Unsaved Changes page
  • Operators Scan
  • Bridge mode display in Overview page
  • Input inversion buttons
  • Dynamic switch port display in side widget
  • Input/Output manipulator
  • Full unicode SMS support
  • IO control and status over SMS
  • MQTT Publisher: added support to send I/O values
  • Ability to install packages stored in backup file
  • IP unblock SMS rule
  • New Modbus TCP Slave register fields
  • New Modbus Alarm redundancy options
  • NTPD version 4.2.8p14

• Improvements
  • Improved mobile interface creation
  • Updated kernel to newest version (3.18.20-msm) from QuecOpen SDK and clean up patches
  • Added HMAC configurations for OpenVPN
  • Added AES ciphers support for OpenVPN
  • Added MTU and gateway metric to mobile interfaces
  • Added DHCP lease range display in the Network → LAN page
  • Added warning messages when deleting interfaces/configurations
  • Added available FW on server status messages in FW upgrade page
  • Added mobile PIN code saving note
  • Changed UPnP redirect delete button style
  • Changed functionality of reset button in the Firewall → Custom Rules page. Now fully resets to default
  • Added hints on all value fields about field validation
  • Added pin information for iostatus SMS rule
  • Removed modem traps if no modem is present
  • Optimized section toggling logic, removing all toggling associated flags required prior optimization
  • Standardized section edit page headers in WebUI Services
  • Improved the look of error pages and messages
  • Updated Wiki links to wiki.teltonika-networks.com
  • Disabled 'Clear data limit' button for inactive interfaces
  • Reordered menu, moved 'Default configuration' to the Backup page, moved 'Diagnostics' to the Troubleshoot page
  • Added credentials input fields to Data to Server
  • Changed hint of 'Allow guest" in the Network Shares page
  • Updated Periodic Reboot service status in the Services page
  • Improved hint for incoming calls option
  • Changed OpenVPN LZO option to a dropdown with an extra 'none' option
  • Added suggestion to create a profile if there are no profiles created in the Profiles → Scheduler page
  • Filtered out unnecessary interfaces ending with _4 _6 in firewall page
  • Changed side widget button color to blue to make it more visible
  • Added 'Dynamic List' option limit (20 elements)
  • Added info message to Events Reporting & Mobile Utilities rules, if selected recipient or sender is a group or no groups are created yet
  • Improved stm32 recv message handling
  • Modbus TCP test now allows reading more than 125 coils/inputs
  • Reworked NTP page, separating general options from NTP specific ones
  • Fixed grammar errors in Mobile page

• Fixes
  • No longer load the rpcd module
  • Removed incorrect SMS character counter from SMS Utilities page
  • Added name validation in the Firewall → Port Forward page, fixed custom protocol value selection and display
  • Added validation for GRE 'Remote subnet IP' option
  • Added missing Mobile Data limit input validation
  • Fixed Schedulers' cells to be of equal width
  • Fixed uploading backup from lower firmware version
  • Fixed SSTP certificate upload function
  • Fixed IPsec 'Aggressive' setting value saving in config file
  • Fixed LAN settings static lease name validation
  • Fixed issue that sometimes caused failures when redirecting to Mobile interface edit page
  • Fixed descriptions in Access Control → Security page
  • Fixed HTTP login while HTTPS session is still active
  • Fixed real time CPU load in the Overview page
  • Fixed advanced static routing display for all routes
  • Fixed file upload error messages in backup page
  • Fixed 'Select' option for Firefox browser
  • Fixed RAM usage display in side widget
  • Fixed access to non existing pages
  • Fixed saving empty message field in Events Reporting rules
  • Fixed showing correct APN settings when upgrading with the 'Keep all settings' option
  • Fixed Events Reporting send test email page display when email contains 2 new lines in a row
  • Fixed phrasing and grammatical mistakes in SMS messages tooltip
  • Fixed LAN Overview section display
  • Fixed early login page load after reboot or backup upload
  • Fixed Package Manager notification display
  • Fixed SMS rule display for different devices
  • Fixed PPTP and L2TP client configuration creation with same name
  • Fixed static route removal if corresponding interface is removed
  • Fixed Realtime Graphs → Traffic tab display
  • Fixed OpenVPN username and password writing to file
  • Fixed time zone sync between Setup Wizard & NTP pages
  • Fixed DHCP lease range validation
  • Fixed possible synchronization loss of Mobile SSID LEDs
  • No longer write anything into Events Log when forcing reboot to prevent device hang-up
  • Fixed restore settings when upgrading from old FW
  • Fixed launching stm32 autoflash script at early boot to avoid possible keep settings loss
  • Removed certain Events Reporting options on devices that don't have the corresponding functionality
  • Fixed recovery from lost connection for MQTT publisher, Modbus MQTT gateway
  • Fixed factory reset script which used to fail when SMS limit database is not initialized

TRB1400_R_00.01.06.1 | 2019.12.19

• New:
  • SMS Gateway POST/GET, Auto Reply, SMS Forwarding
  • net-snmp 5.8 support
  • Modbus TCP slave, TCP master, data to server
  • Firmware over the air support
  • Events log
  • Mobile data limit
  • SMS limit
  • Static routes
  • RMS status, action and connect SMS rules
  • SMS I/O status rule
  • Configuration Profiles
  • Auto-APN

• Improvements
  • WebUI style improvements
  • I/O POST/GET, Output Scheduler
  • Added specific LED blinking on firmware upgrade, device boot and mobile indication
  • Added password protected access shell
  • Changed GPIO direction and state SMS rules

• Fixes
  • Added default device name
  • Access control fixes
  • Fixed RMS download, upload and data sending while connecting

TRB1400_R_00.01.05 | 2019.09.30

• New:
  • Firewall sync with upstream

• Improvements
  • Improved partition checking logic
  • Upgraded modem firmware

• Fixes
  • Removed alsa-intf dependency
  • Disabled DROP SSDP rules
  • Fixed invalid magic number message
  • Fixes for multiple APNs
  • Disabled MCM on full modem control over serial
  • Fixed Deny data roaming option setting wrong values
  • Fix not showing I/O (dwi, relay, input) content in certain devices

TRB1400_R_00.01.04.1 | 2019.08.02

• Fixes
  • Input/Output related fixes

TRB1400_R_00.01.04 | 2019.07.15

• New features
  • Added Input/Output configuration and overview page
  • Added I/O status management SMS Utilities rules

TRB1400_R_00.01.03 | 2019.06.14

• New features
  • Added Wake on LAN functionality
  • Added System → Administration → Diagnostics page
  • Added deny roaming option

• Improvements
  • Updated WebUI notification box style

• Fixes
  • Status → System table style fix
  • Fixed reset mobile bytes received/sent counter after connection restart
  • Fixed IPsec connection after reboot
  • Fixed call utilities mobile turn off rule

TRB1400_R_00.01.02 | 2019.05.22

• New features
  • Added Profiles functionality
  • Added Modbus TCP functionality
  • Added MQTT broker and publisher support
  • Add L2TP support
  • Added PPTP support
  • Added GRE Tunnel support

TRB1400_R_00.01.01.2 | 2019.03.25

• New features
  • Added Mobile Utilities service

• Improvements
  • Improved modem boot up speed
  • Improved modem compression ratio
  • Added requirement to change password on first boot
  • Disallow keep settings when flashing an older firmware

• Fixes
  • Firewall append config with reload option
  • Added OpenVPN certs removal on OpenVPN tunnel section deletion
  • Various fixes for OpenVPN page
  • Backup/keep-settings fixed to include OpenVPN certificates and tlt auth files
  • Backup/keep-settings fixed to preserve root password
  • Added NTRIP client init
  • Changed NTRIP server IP address field to support hostnames
  • I/O failure fix due to updated hardware
  • Fixed backup file uploading
  • Syntax fix on the RMS page
  • Fix signal LED no. 1 being always on
  • Reset modem after configuration changes fix
  • DDNS service restart after reboot/interface reload fix
  • Fixed renewing CLI session
  • Fixed setting date on boot
  • sysup fix
  • sodog fix

TRB1400_R_00.01.00 | 2019.02.01

• Improvements
  • New versioning system

TRB14X_R_00.00.11 | 2019.01.16

• New features
  • Added CLI service
  • Added Static Routes page

• Improvements
  • Added some visual style changes

TRB14X_R_00.00.10 | 2018.12.06

• New features
  • Initial FW release
  • Added NTP service
  • Added Dynamic DNS service
  • Added Auto Reboot service
  • Added Input/Output service