RMA

From Teltonika Networks Wiki
Main Page > General Information > RMA

Introduction

TELTONIKA NETWORKS gives guarantee for its products for a period of 24 months. All batteries carry a reduced 6 month warranty period. If a product fails within mentioned warranty period the product can be:

  • Repaired;
  • Replaced with a new product;
  • Replaced with an equivalent repaired product fulfilling the same functionality;
  • Replaced with a different product fulfilling the same functionality in case of EOL for the original product.

During the return merchandise authorization (RMA) part of the warranty process, a Teltonika-Networks engineer examines the information provided by a client in an RMA request form in order to determine whether the equipment is eligible for warranty repair. The RMA request form contains company, addressing and malfunctioning product information and must be filled out by the product's owner and approved by a Teltonika-Networks engineer before returning a product.

However, take note that not all issues are covered by the warranty policy. Refer to the table below for information on which hardware related issues are covered by the warranty service and which issues are not.

Hardware Issues

The table below contains information on which hardware related issues are covered by the warranty service and which issues are not:

Visible physical damage (device damaged, antenna connectors damaged...):
  • Visible physical damage on device PCB;
  • Visible physical damage on mobile, WiFi, GPS or Bluetooth antenna connectors.
Hardware issue Does device need to be sent under RMA? Next step

Device does not start. LED does not blink at all when device is powered up (power range depends on the device);

  • If client ensures that device does have the needed power supply and still does not start, such device should be sent to warranty.

YES, if this issue is true

Steps to fill out RMA form:

1. Login to HelpDesk: https://viphelpdesk.teltonika.lt/ 1.

2. Create new ticket and fill in the information about the non-functioning product.

3. Follow the instructions from the engineer and wait until your form is approved.

4. After the form is approved you will get it through E-mail.

5. Print the RMA form and send it together with the shipment.

1 If you do not have a Helpdesk account, please contact your sales manager.

Device does not start. Only the power LED lights up when the device is powered up.
  • If client ensures that device does have the needed power supply and still does not start, such device should be sent to warranty.
LAN/WAN ports not working:
  • LED indicator does not light up when ethernet cable is inserted;
  • LED indicator light up when no ethernet cable is inserted;
  • Make sure that ethernet cables are not damaged or faulty.

Modem module is not recognized:

  • Receiving message in WebUI "modem not found";
  • No visible "Mobile" section in WebUI.

SIM card failure. Device does not see SIM card:

  • Check SIM card itself, if there is no physical damage;
  • Check if SIM card is seen by cell phone or other cellular device;
  • Check if PIN code is not set;
  • Check if device is working with another SIM card, another operator SIM card;
  • Check if mobile antenna is connected.

YES, if none of the mentioned points helps

  • Visible physical damage on the external GPS antenna;
  • Visible physical damage on the external mobile antenna;
  • Visible physical damage on the external WiFi antenna;
  • Visible physical damage on the external Bluetooth antenna;
  • Visible physical damage on the other external accessories.

NO, if at least one issue is true, offer to change an antenna

Contact your sales manager
Device was damaged because it was operating or being stored outside of the determined temperature range. rowspan="6" style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; background: white; text-align: center;" NO
Device was damaged because it was operating or being stored not in accordance with its IP (Ingress Protection) code (for example, the device was exposed to too much water or dust because of being placed in improper conditions).
Device was damaged intentionally, accidentally or because of improper use.


Firmware Issues

The table below contains information on which firmware related issues are covered by the warranty service and which issues are not:

Firmware issue Does device need to be sent under RMA? Next step

Device is in boot mode (all 4 Ethernet LEDs are flashing).

NO Contact support

Device is in safe mode.

Device's WebUI is not reachable for an unknown reason.

The device is unresponsive because the user modified its firmware or installed a firmware not approved by Teltonika.
There is another issue on the device related to its firmware.
There is another issue on the device related to incorrect configuration.

The recommended course of action when firmware issues are encountered is to contact your sales representative if the device was purchased directly from Teltonika or contact Teltonika support if VIP HelpDesk access is provided to you. If you purchased the device elsewhere, contact the distributor that sold you the device.

IMPORTANT: in any of the defined cases, please contact your sales representative or technical support before sending the device(s) to warranty, as without the RMA form confirmation the devices will not be accepted.