RUT850 GPS

From Teltonika Networks Wiki
Revision as of 14:16, 16 September 2020 by Dziugas (talk | contribs)

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)
Main Page > EOL Products > RUT850 > RUT850 Manual > RUT850 WebUI > RUT850 Services section > RUT850 GPS

The information in this page is updated in accordance with the RUT850_R_00.01.04 firmware version.

Summary

The Global Positioning System (GPS) is a space-based radionavigation system. This page is an overview of the GPS service in RUT850 routers.

Map

The Map page displays the device's current coordinates and position on the map. To see the device's location on the map, make sure to attach the GPS antenna on the router and enable GPS in the General page.

The figure below is an example of the Map page:

File:Networking device manual gps map v2.png

General

The General section is used to enable the GPS service and the support for different types satellites. Once you turn on GPS, you can check the Map page in order to see if the router has obtained a GPS fix. It is very important to attach the GPS antenna on the router and place it outside (not inside of a building). The router will not be likely to obtain a GPS fix otherwise.

The figure below is an example of the General page.

Networking rut850 manual gps general v1.png

NMEA

The NMEA page is used to configure settings related to NMEA sentence collecting and forwarding.

NMEA forwarding


The NMEA forwarding section is used to configure and enable NMEA forwarding. The figure below is an example of the NMEA forwarding section and the table below provides information on the fields contained in that section:

File:Networking device manual gps nmea nmea forwarding v2.png

Field Value Description
Enabled yes | no; default: no Turns NMEA forwarding on or off.
Hostname ip | host; default: 192.168.1.5 IP address or hostname of the server to which NMEA data will be forwarded.
Port integer [0..65535]; default: 8500 Port number off the server to which NMEA data will be forwarded.
Protocol TCP | UDP; default: TCP Protocol that will be used to send NMEA data.

NMEA forwarding cache


The router caches NMEA forwarding information if NMEA forwarding is enabled. This section is used to select the memory type where the cache will be stored and the maximum amount of data that will be saved:

File:Networking device manual gps nmea nmea forwarding cache v2.png

Field Value Description
Type ram | flash; default: ram Selects which type of memory will be used for storing NMEA forwarding cache.
Maximum sentences integer; default: 5000 Maximum amount of NMEA sentences that will be saved in the cache before older entries are deleted and replaced by new ones.
File filepath; default: none Location of the file where NMEA forwarding cache information will be stored. This field becomes visible only when the selected memory type is "flash".

NMEA collecting


The NMEA collecting section is used to enable NMEA sentence gathering and storing. The figure below is an example of the NMEA collecting section and the table below provides information on the fields contained in that section:

File:Networking device manual gps nmea nmea collecting v2.png

Field Value Description
Enabled yes | no; default: no Turns NMEA sentence collecting on or off.
Location filepath; default: none Location of the file where NMEA sentences will be stored. This field becomes visible only when NMEA collecting is enabled.

NMEA sentence settings


The NMEA sentence settings section provides the possibility to configure which NMEA sentences will be forwarded or collected and at what frequency. The figure below is an example of the NMEA sentence settings section and the table below provides information on the fields contained in that section:

Networking rut850 manual gps nmea nmea sentence settings v1.png

Field Value Description
Forwarding enabled yes | no; default: no Enables forwarding for the adjacent NMEA sentence.
Forwarding interval integer; default: 5 NMEA sentence forwarding frequency in seconds.
Collecting enabled yes | no; default: no Enables collecting for the adjacent NMEA sentence.
Collecting interval integer; default: 5 NMEA sentence collecting frequency in seconds.


NMEA sentence reference table:

NMEA sentence name Description
GPGSV Number of GPS satellites in view.
GPGGA GPS fix data.
GPVTG Track made good and speed relative to the ground.
GPRMC Recommended minimum specific GPS/Transit data.
GPGSA GPS DOP and active satellites.

HTTPS

The HTTPS page can be used to configure data sending to an HTTP(S) server.

HTTPS/HTTP Server Settings


The HTTPS/HTTP Server Settings section is used to enable GPS data sending to an HTTP or HTTPS server:

File:Networking device manual gps https https server settings v2.png

Field Value Description
Enabled yes | no; default: no Turns data sending to an HTTP/HTTPS server on or off.
URL ip | host; default: 192.168.1.5 IP address or hostname of the HTTP/HTTPS server.

TAVL Settings


The TAVL Settings section is used to select which data will be sent to the TAVL server:

Networking rut manual gps https tavl settings.png

Field Value Description
Send GSM signal yes | no; default: no Includes GSM signal strength information in the GPS data sent to server.
Send analog input yes | no; default: no Includes analog input state in GPS data package to be sent to server.
Send digital input (1) yes | no; default: no Includes digital input #1 state in the GPS data sent to server.
Send digital input (2) yes | no; default: no Includes digital input #2 state in GPS data package to be sent to server.

AVL

The AVL page is used to set up GPS data sending to an AVL server.

AVL Server Settings


The AVL Server Settings section is used to configure the main parameters of data sending to an AVL server. The figure below is an example of the AVL Server Settings section and the table below provides information on the fields contained in that section:

Networking rut manual gps avl avl server settings.png

Field Value Description
Enabled yes | no; default: no Turns data sending to AVL server on or off.
Hostname ip | host; default: 192.168.1.5 IP address or hostname of an AVL server.
Port integer [0..65535]; default: 8501 TCP/UDP port number of the AVL server to which the router will be connecting.
Protocol TCP | UDP; default: TCP Protocol that will be used for communication with the AVL server.

Main rule


The Main rule section defines how and when GPS data will be collected and sent to a specified AVL server. Refer to the figure and table below for information on the configuration fields of Main Rule.

File:Networking device manual gps avl main rule v3.png

Field Value Description
Enable yes | no; default: yes Turns the main rule on or off.
Rule priority Low priority level | High priority level | Panic priority level | Security priority level; default: Low priority level The rule's priority. Different priority settings add different flags to event packets, so they can be displayed differently in the receiving system. The router sends data of higher priority first. Priority levels from highest to lowest are as follows:
  1. Security
  2. Panic
  3. High
  4. Low
Collect period integer [1..999999]; default: 50 How often (in seconds) data will be collected.
Min distance integer [1..999999]; default: 50 Minimum distance change (in meters) before sending records.
Min angle integer [1..360]; default: 50 Minimum angle change (in degrees) before sending records.
Min saved records integer [1..32]; default: 20 Minimum amount of gathered records before sending.
Send period integer [0..999999]; default: 20 How often (in seconds) gathered data is sent.

Secondary Rules


The Secondary rules section provides you with the possibility to create additional data sending rules. The difference from the main rule is that the secondary rules only send data when the router uses a specified type of WAN and when the digital isolated output is in the specified state.

Refer to the figure and table below for information on the configuration fields of the Secondary rules section.

File:Networking device manual gps avl secondary rules v3.png

Field Value Description
Enable yes | no; default: no Turns the secondary rule on or off.
WAN Mobile Both | Mobile Home | Mobile Roaming | WiFi | Wired; default: Mobile Home Selects which type of WAN will trigger the rule.
Digital Isolated Input Low logic level | High logic level | Both; default: Low logic level Selects which input state will trigger the rule.
Rule priority Low priority level | High priority level | Panic priority level | Security priority level; default: Low priority level The rule's priority. Different priority settings add different flags to event packets, so they can be displayed differently in the receiving system. The router sends data of higher priority first. Priority levels from highest to lowest are as follows:
  1. Security
  2. Panic
  3. High
  4. Low
Collect period integer [1..999999]; default: 25 How often (in seconds) data will be collected.
Min distance integer [1..999999]; default: 200 Minimum distance change (in meters) before sending records.
Min angle integer [1..360]; default: 30 Minimum angle change (in degrees) before sending records.
Min saved records integer [1..32]; default: 20 Minimum amount of gathered records before sending.
Send period integer [0..999999]; default: 50 How often (in seconds) gathered data is sent.

AVL Configuration


The AVL Configuration section is used to add additional secondary GPS data sending rules.

File:Networking device manual gps avl gps configuration v2.png

TAVL Settings


The TAVL Settings section is used to select which data will be sent to the TAVL server:

Networking rut manual gps avl tavl settings.png

Field Value Description
Send GSM signal yes | no; default: no Includes GSM signal strength information in the GPS data sent to server.
Send analog input yes | no; default: no Includes analog input state in GPS data package to be sent to server.
Send digital input (1) yes | no; default: no Includes digital input #1 state in the GPS data sent to server.
Send digital input (2) yes | no; default: no Includes digital input #2 state in GPS data package to be sent to server.

GPS Geofencing

A geofence is a virtually defined boundary for a real-world geographic area. The GPS Geofencing page provides you with the possibility to set this custom area and apply rules that will inform you when the device leaves or enters the geofence.

File:Networking device manual gps gps geofencing 1 v2.png

The figure below is an example of GPS Geofencing configuration and the table below provides information related to that configuration:

File:Networking device manual gps gps geofencing details v2.png

Field Value Description
Enable yes | no; default: no Turns the Geofence rule on or off
Longitude (X) degrees [-180.000000..180.000000]; default: 0.000000 East-west position of a point on the Earth's surface. Combining this and the Latitude information will produce a point on the world map that will serve as the center of the geofence area.
Latitude (Y) degrees [-90.000000..90.000000]; default: 0.000000 North-south position of a point on the Earth's surface. Combining this and the Longitude information will produce a point on the world map that will serve as the center of the geofence area.
Radius integer [1..999999]; default: 200 Radius (in meters) of the geofence area.
Generate event on Exit | Enter | Enter/exit; default: Exit Specifies whether the rule should be triggered when the device enters the geofence area, leaves it or on both events.
Get current coordinates - (interactive button) Obtains the device's current coordinates and places them in the Longitude and Latitude fields.

See also