RUT900 First Start

From Teltonika Networks Wiki
Revision as of 17:59, 6 November 2019 by Dziugas (talk | contribs) (Protected "RUT900 First Start" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite)))

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)
Main Page > EOL Products > RUT900 > RUT900 First Start

This Wiki page contains the online version of the Quick Start Guide (QSG) for the RUT900 3G Router. Here you will find an overview of the various components found on the front and back sides of a RUT900 device, basic hardware installation, first login information, device specifications and general safety information. It is highly recommended that you acquaint yourself with with the Quick Start Guide before using the device. If you own a RUT900 device, you can also find a printed version of the Quick Start Guide in the device's package.

Rut900 hd 7 demo.png

Front view

No. Description
1 LAN Ethernet ports
Networking rut9xx manual panels front v1.png
2 WAN Ethernet port
3 LAN LEDs
4 WAN LED
5 Power socket
6 Power LED
7 Mobile connection status LED
8 Mobile signal strength indication LEDs

Back view

No. Description
Networking rut9xx manual panels back v1.png
1 LTE antenna connectors
2 WiFi antenna connectors
3 Reset button
4 SIM card slots

Connectors

Power socket pinout
Trb142 power socket pinout v3.png
No. Description Wire color
1 Power Red
2 Ground Black
3 I/O Green
4 I/O White
.

Hardware installation

  1. Remove the SIM card slot tray(s) with the pin needle. Insert your SIM card(s) and push the tray(s) back into the router. Correct SIM card orientation can be seen in the figure below:
    Rut900 sim card insertion v1.png
  2. Attach 3G and WiFi antennas
  3. Connect the power adapter to the power socket located on the front panel of the device. Then plug the other end of the power adapter into a power outlet.
  4. Connect to the device wirelessly (SSID: RUT900_****) or use an Ethernet cable.

Configure your computer (Windows)

  1. Enable the wireless network connection (go to Start → Control Panel → Network and Internet → Network and Sharing Center. In the left panel click the Change adapter settings link. Right click on Wireless Network Connection and select Enable).

    Qsg rutxxx enable wireless connection v2.png

  2. Setup wireless network adapter on your computer (right click on Wireless Network Connection and select Properties. After that select Internet Protocol Version 4 (TCP/IP) and click Properties).
  3. Select Obtain IP address and Obtain DNS server address automatically if they are not selected. Click OK.

    Qsg rutxxx obtain ip address automatically v2.png

  4. Right click on Wireless Network Connection and select Connect to see available wireless networks.

    Qsg rutxxx connect to wireless network v2.png

  5. Choose the wireless network RUT900_**** from the list and click Connect. Enter the WiFi password located on the device's label.

    Rut900 connect to wireless ssid v1.png

Login to device

  1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
  2. Use the following login information when prompted for authentication:

    Qsg rutxxx routers web interface v2.png

  3. After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router's WebUI before you change the password.
  4. When you change the router's password, the Configuration Wizard will start. The Configuration Wizard is a tool used to setup some of the router's main operating parameters.
  5. Go to the Status → Network page and pay attention to the Signal Strength indication. To maximize cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions (you can find information on signal strength recommendations here).

    Qsg rutxxx login to device v2.png

Safety information

The RUT900 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

Radio specifications
RF technologies GSM, GPRS, EDGE, UMTS/HSPA+, WiFi
Max. RF power 33 dBm@GSM, 24 dBm@WCDMA, 20 dBm@WiFi
Bundled accessories specifications*
Power AC/DC power adapter 9 V 1 A, 4 pin plug
GSM/WCDMA antenna 698~960/1710~2690 MHz, 50 Ω, VSWR < 3, gain** 3 dBi, omnidirectional, SMA male connector
WiFi antenna 2400~2483.5 MHz, 50 Ω, VSWR < 2, gain** 5 dBi, omnidirectional, RP-SMA male connector

* Order code dependent.

** Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

Qsg rut950 manual.PNG This sign on the package means that is necessary to read the User's Manual before you start using the device

Qsg rut950 recycle.PNG This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste

Qsg rut950 ce.PNG Hereby, Teltonika declares that the radio equipment type RUT900 is in compliance with Directives: 2014/53/EU, 2014/35/EU, 2014/30/EU. The full text of the EU declaration of conformity is available at the following internet address: https://teltonika-networks.com/product/rut900/