Difference between revisions of "RUT900 UPNP"
From Teltonika Networks Wiki
| Line 15: | Line 15: | ||
<tr> | <tr> | ||
<td>Enable</td> | <td>Enable</td> | ||
| − | <td>yes | + | <td>yes | no; Default: '''no'''</td> |
<td>Toggles UPnP ON or OFF</td> | <td>Toggles UPnP ON or OFF</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Use secure mode</td> | <td>Use secure mode</td> | ||
| − | <td>yes | + | <td>yes | no; Default: '''yes'''</td> |
<td>Toggles Secure mode ON or OFF</td> | <td>Toggles Secure mode ON or OFF</td> | ||
</tr> | </tr> | ||
| Line 38: | Line 38: | ||
<tr> | <tr> | ||
<td>Use UPnP port mapping</td> | <td>Use UPnP port mapping</td> | ||
| − | <td>yes | + | <td>yes | no; Default: '''yes'''</td> |
<td>Toggles UPnP port napping ON or OFF</td> | <td>Toggles UPnP port napping ON or OFF</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Use NAT-PMP port mapping</td> | <td>Use NAT-PMP port mapping</td> | ||
| − | <td>yes | + | <td>yes | no; Default: '''yes'''</td> |
<td>Toggles NAT-PMP port mapping ON or OFF</td> | <td>Toggles NAT-PMP port mapping ON or OFF</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Device UUID</td> | <td>Device UUID</td> | ||
| − | <td>yes | + | <td>yes | no; Default: '''yes'''</td> |
<td>Specify Universal unique ID of the device</td> | <td>Specify Universal unique ID of the device</td> | ||
</tr> | </tr> | ||
| Line 72: | Line 72: | ||
<tr> | <tr> | ||
<td>Ecternal ports</td> | <td>Ecternal ports</td> | ||
| − | <td>integer [0..65535]] | + | <td>integer [0..65535]] | range of integers [0-65535]; Default: '''1024-65535'''</td> |
<td>External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | <td>External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | ||
</tr> | </tr> | ||
| Line 82: | Line 82: | ||
<tr> | <tr> | ||
<td>Internal ports</td> | <td>Internal ports</td> | ||
| − | <td>integer [0..65535]] | + | <td>integer [0..65535]] | range of integers [0-655355]; Default: '''1024-65535'''</td> |
<td>Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | <td>Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>Action</td> | <td>Action</td> | ||
| − | <td>allow | + | <td>allow | deny; Default: '''allow'''</td> |
<td>Allows or forbids the UPnP service to open the specified port</td> | <td>Allows or forbids the UPnP service to open the specified port</td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | |||
| + | [[Category:RUT900 WebUI]] | ||
Revision as of 09:50, 1 March 2019
Main Page > RUT Routers > RUT900 > RUT900 Manual > RUT900 WebUI > RUT900 Services section > RUT900 UPNPSummary
UPnP allows clients in the local network to automatically configure the router. This chapter is a summary of the UPnP function in RUT routers
General Settings
| field name | value | description |
|---|---|---|
| Enable | yes | no; Default: no | Toggles UPnP ON or OFF |
| Use secure mode | yes | no; Default: yes | Toggles Secure mode ON or OFF |
Advanced Settings
| field name | value | description |
|---|---|---|
| Use UPnP port mapping | yes | no; Default: yes | Toggles UPnP port napping ON or OFF |
| Use NAT-PMP port mapping | yes | no; Default: yes | Toggles NAT-PMP port mapping ON or OFF |
| Device UUID | yes | no; Default: yes | Specify Universal unique ID of the device |
UPnP ACLs
ACLs specify which external ports may be redirected to which internal addresses and ports
| field name | value | description |
|---|---|---|
| Comment | string; Default: Allow high ports | Adds a comment to this rule |
| Ecternal ports | integer [0..65535]] | range of integers [0-65535]; Default: 1024-65535 | External port(s) which may be redirected. May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers |
| Internal Addresses | ip/integer [0..32]; Default: 0.0.0.0/0 | Internal address to be redirect to |
| Internal ports | integer [0..65535]] | range of integers [0-655355]; Default: 1024-65535 | Internal port(s) to be redirect to May be specified as a single port or a range of ports. To specify a range use a dash ('-') symbol between two integer numbers |
| Action | allow | deny; Default: allow | Allows or forbids the UPnP service to open the specified port |
