RUTX12 Failover

From Teltonika Networks Wiki
Revision as of 20:07, 8 April 2020 by Dziugas (talk | contribs) (Created page with "==Summary== This chapter is an overview of the Failover and Load Balancing functions in RUTX12 routers. ===Failover=== ---- This function allows you to back up your primary co...")

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)
Main Page > RUTX Routers > RUTX12 > RUTX12 Manual > RUTX12 WebUI > RUTX12 Network section > RUTX12 Failover

Summary

This chapter is an overview of the Failover and Load Balancing functions in RUTX12 routers.

Failover


This function allows you to back up your primary connection in case it goes down. For example, when primary connection goes down, router will try to use second configured backup interface. If second interface will also become unavailable, router will try to use third backup interface.

In order to set priorities, simply press left mouse click on the interface, then drag it to the 1st, 2nd or other position and then press Save & Apply.

Below is an example of Failover settings section.1139x1139pxBy pressing Edit button, you can find more Failover interface settings. More information and example are presented below.on; Default: off Toggles the interface ON or OFF Interval Default: 3 Number of seconds between each test Method Default: Ping Method, how internet connection will be tested Track IP IP;Default: 8.8.4.4; 8.8.8.8 The hosts to test if interface is still alive. If this value is missing the interface is always considered up Reliability Default: 1 Number of hosts that must reply for the test to be considered as successful. Ensure there are at least this many hosts defined or the interface will always be considered down Count Default: 1 Number of pings to send to each host with each test Up Default: 3 Number of successful tests to considered link as alive Down Default: 3 Number of failed tests to considered link as dead Load Balancing Load balancing lets users create rules that divide traffic between different interfaces. Below is an example of Load Balancing settings window.1145x1145pxAs you may notice from the image above, the configuration is very simple. You can assign ratio values to WAN interfaces. The ratio values represent a percentage of load that will go through an interface. For example, if you set that 3 parts of traffic would go through the Mobile interface and 2 parts would go through the Wired interface, it would mean that roughly 60% (3/5) of data will be transferred through Mobile, 40% (2/5) through Wired. If the ratios would be different, say Mobile: 5, Wired: 10, then 33% (5/15) of data would be transferred through Mobile, and 66% (10/15) would go through Wired. If you press Edit button, you will be transferred to the same interface settings that were described in Failover section. 146x1146px

field namevaluedescription
Enableoff | on; Default: offToggles the interface ON or OFF
IntervalDefault: 3Number of seconds between each test
MethodDefault: PingMethod, how internet connection will be tested
Track IPIP;Default: 8.8.4.4; 8.8.8.8The hosts to test if interface is still alive. If this value is missing the interface is always considered up
ReliabilityDefault: 1Number of hosts that must reply for the test to be considered as successful. Ensure there are at least this many hosts defined or the interface will always be considered down
CountDefault: 1Number of pings to send to each host with each test
UpDefault: 3Number of successful tests to considered link as alive
DownDefault: 3Number of failed tests to considered link as dead

Load Balancing


Load balancing lets users create rules that divide traffic between different interfaces. Below is an example of Load Balancing settings window.1145x1145pxAs you may notice from the image above, the configuration is very simple. You can assign ratio values to WAN interfaces. The ratio values represent a percentage of load that will go through an interface. For example, if you set that 3 parts of traffic would go through the Mobile interface and 2 parts would go through the Wired interface, it would mean that roughly 60% (3/5) of data will be transferred through Mobile, 40% (2/5) through Wired. If the ratios would be different, say Mobile: 5, Wired: 10, then 33% (5/15) of data would be transferred through Mobile, and 66% (10/15) would go through Wired.

If you press Edit button, you will be transferred to the same interface settings that were described in Failover section.