Line 1: |
Line 1: |
| + | <p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.4'''] firmware version .</p> |
| + | |
| ==Introduction== | | ==Introduction== |
| This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RUTOS devices. | | This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RUTOS devices. |
| | | |
− | ===Configuring WAN as LAN=== | + | ==Alternative 1== |
− | * First you want to make sure that you have '''ADVANCED mode''' enabled. This will allow you to choose from a larger variety of settings.
| + | |
− | [[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]] | + | Set your WebUI to '''Basic Mode''': |
− | ----
| + | |
− | * After that navigate to Network > Interfaces
| + | [[File:Basic mode.png|border|center|class=tlt-border|890x67px]] |
− | [[File:Network_interface_settings.png|200px|border|class=tlt-border]] | + | |
| + | Navigate to '''Network → LAN → edit LAN''' the instance: |
| + | [[File:Edit LAN interface.png|border|center|class=tlt-border|766x90px]] |
| + | |
| + | Once there, '''enable the Use WAN port as LAN''': |
| + | [[File:Use WAN as LAN.png|border|center|class=tlt-border|742x295px]] |
| + | |
| + | ==Alternative 2== |
| + | |
| + | Enable the '''ADVANCED mode''' on the WebUI . This will allow you to choose from a larger variety of settings: |
| + | [[File:Advanced mode.png|border|center|class=tlt-border|874x63px]] |
| + | |
| + | Navigate to '''Network → Interfaces → General''' and '''disable WAN and WAN6''' interfaces: |
| + | |
| + | [[File:WAN down.png|border|center|class=tlt-border|826x173px]] |
| + | |
| + | Click on '''edit the LAN''' interface and once a new window pops-up '''go to''' '''Physical settings'''. There, under the '''Interface''' '''add eth1''': |
| + | |
| + | [[File:Add eth1.png|border|center|class=tlt-border|902x265px]] |
| | | |
− | * Disable WAN interface
| + | ==Test the configuration== |
− | [[File:Interfaces disable wan.png|border|class=tlt-border|1100px]]
| |
− | ----
| |
− | * Next we will '''edit''' our LAN interface and navigate to '''Physical settings''' where we will add Interface item from the dropdown menu.
| |
− | [[File:Physical settings of interface lan.png|border|1100px|class=tlt-border]]
| |
− | ----
| |
− | * Select Ethernet Adapter item, by default it's '''eth1'''
| |
− | [[File:Ethernet adapter in lan interface.png|border|class=tlt-border]]
| |
− | ----
| |
− | * It should result in something like this.
| |
− | [[File:Eth1 appears in lan interface.png|border|class=tlt-border|1100px]]
| |
− | ----
| |
− | * Once you're done with configurations above just '''save any changes you made'''. Now head to VLAN settings and check if WAN VLAN ID 1 is disabled, and ID 2 is untagged.
| |
− | [[File:Vlan settings for wan as lan.png|border|class=tlt-border|1100px]]
| |
− | ----
| |
| At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router. | | At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router. |
| + | [[File:Pings useful.png|border|center|class=tlt-border|734x232px]] |