Line 46: |
Line 46: |
| Refer to the sections below for information on editing SQM instances. | | Refer to the sections below for information on editing SQM instances. |
| | | |
− | ===Basic Settings=== | + | ===General Setup=== |
| ---- | | ---- |
− | The <b>Basic Settings</b> section is used to set download and upload speed limits for a selected network interface. | + | The <b>General Setup</b> section is used to set download and upload speed limits for a selected network interface. |
| | | |
− | [[File:Networking_rutos_manual_traffic_shaping_sqm_basic_settings.png|border|class=tlt-border]] | + | [[File:Networking rutos manual traffic shaping sqm general setup73.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 70: |
Line 70: |
| <tr> | | <tr> |
| <td>Download speed (kbit/s)</td> | | <td>Download speed (kbit/s)</td> |
− | <td>integer [0..9999999999999999]; default: <b>none</b></td> | + | <td>integer [0..2147483647]; default: <b>none</b></td> |
| <td>Limits the download speed (ingress) of the selected interface to the value specified in this field.</td> | | <td>Limits the download speed (ingress) of the selected interface to the value specified in this field.</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Upload speed (kbit/s)</td> | | <td>Upload speed (kbit/s)</td> |
− | <td>integer [0..9999999999999999]; default: <b>none</b></td> | + | <td>integer [0..2147483647]; default: <b>none</b></td> |
| <td>Limits the upload speed (egress) of the selected interface to the value specified in this field.</td> | | <td>Limits the upload speed (egress) of the selected interface to the value specified in this field.</td> |
| </tr> | | </tr> |
Line 84: |
Line 84: |
| The <b>Advanced Settings</b> section describes the internal logic of the SQM configuration. | | The <b>Advanced Settings</b> section describes the internal logic of the SQM configuration. |
| | | |
− | [[File:Networking_rutos_manual_traffic_shaping_sqm_advanced_settings.png|border|class=tlt-border]] | + | [[File:Networking rutos manual traffic shaping sqm advanced settings73.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 282: |
Line 282: |
| (for example, video streaming, SSH) at a higher priority and less important traffic (FTP, HTTP) at a lower priority. | | (for example, video streaming, SSH) at a higher priority and less important traffic (FTP, HTTP) at a lower priority. |
| | | |
− | [[File:Networking rutos manual traffic shaping qos classification rules.png|border|class=tlt-border]] | + | [[File:Networking rutos manual traffic shaping qos classification rules73.png|border|class=tlt-border]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 297: |
Line 297: |
| <tr> | | <tr> |
| <td>Source host</td> | | <td>Source host</td> |
− | <td>All | IP; default: <b>All</b></td> | + | <td>All | IP | -- Custom --; default: <b>All</b></td> |
| <td>Host(s) from which data will be transmitted.</td> | | <td>Host(s) from which data will be transmitted.</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Destination host</td> | | <td>Destination host</td> |
− | <td>All | IP; default: <b>All</b></td> | + | <td>All | IP | -- Custom --; default: <b>All</b></td> |
| <td>Host(s) to which data will be transmitted.</td> | | <td>Host(s) to which data will be transmitted.</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Protocol</td> | | <td>Protocol</td> |
− | <td>All | TCP | UDP | ICMP | -- custom --; default: <b>All</b></td> | + | <td>All | TCP | UDP | ICMP | -- Custom --; default: <b>All</b></td> |
| <td>Data transmission protocol to match the rule.</td> | | <td>Data transmission protocol to match the rule.</td> |
| </tr> | | </tr> |
| <tr> | | <tr> |
| <td>Ports</td> | | <td>Ports</td> |
− | <td>All | integer [0..65535]; default: <b>none</b></td> | + | <td>All | integer [1..65535]; default: <b>none</b></td> |
| <td>Port number(s) to match the rule. You can enter multiple ports by separating them by commas (e.g., <i>22,53,80</i>).</td> | | <td>Port number(s) to match the rule. You can enter multiple ports by separating them by commas (e.g., <i>22,53,80</i>).</td> |
| </tr> | | </tr> |