0
edits
Changes
Template:Netoworking rut configuration example cisco ipsec (view source)
Revision as of 10:45, 2 April 2020
, 10:45, 2 April 2020→Cisco configuration
* One RUTxxx router of any type
* One RUTxxx router of any type
* One Cisco router of any type
* One Cisco router (this configuration example was created using Cisco RV340W)
* At least one router must have a Public Static or Public Dynamic IP address
* At least one router must have a Public Static or Public Dynamic IP address
* At least one end device (PC, Laptop, Tablet, Smartphone) to configure the routers
* At least one end device (PC, Laptop, Tablet, Smartphone) to configure the routers
==Configuration scheme==
==Configuration scheme==
[[File:Networking_rutxxx_configuration_example_ipsec_topology_v1.png|border|class=tlt-border|1100x1100px]]
[[File:Networking_rutxxx_configuration_example_ipsec_topology_v2.png|border|class=tlt-border|1100x1100px]]
==RUT configuration==
==RUT configuration==
# Write '''Pre-shared key''' (a shared password used for authentication between the peers. The value of this field must match on both instances).
# Write '''Pre-shared key''' (a shared password used for authentication between the peers. The value of this field must match on both instances).
# Add '''Secret's ID selector''' (Cisco LAN IP).
# Add '''Secret's ID selector''' (Cisco LAN IP).
# Press '''Save'''
# Press '''Save'''.
==Cisco configuration==
==Cisco configuration==
Connect to router's WebUI, go to '''VPN > IPsec Profiles''' and apply the following configuration.
Connect to router's WebUI, go to '''VPN > IPsec Profiles''' and apply the following configuration.
[[File:Networking_rutxxx_configuration_example_ipsec_cisco_profiles_v1.png|border|class=tlt-border]]
[[File:Networking_rutxxx_configuration_example_ipsec_cisco_profiles_v2.png|border|class=tlt-border]]
# Add '''Profile Name''' (anything you want).
# Add '''Profile Name''' (anything you want).
# Select '''Group: Group''' (5).
# Select '''Group: Group''' (5).
When you are do with '''IPsec Profiles''', save settings, go to '''Site-to-Site''' settings and apply the following configuration:
When you are done with '''IPsec Profiles''', save settings, go to '''Site-to-Site''' settings and apply the following configuration:
[[File:Networking_rutxxx_configuration_example_ipsec_cisco_s2s_v2.png|border|class=tlt-border]]
[[File:Networking_rutxxx_configuration_example_ipsec_cisco_s2s_v2.png|border|class=tlt-border]]
# Enable it.
# '''Enable''' it.
# Connection Name: RUT
# Select '''IPsec Profile''' (RUT).
# Set '''Interface''' (your internet source).
# Interface: Internet Source
# Select '''Remote Endpoint''' (static IP).
# Remote Endpoint: Static IP, RUT Public IP
# Write '''RUT Public IP'''.
# Pre Shared Key: 123456
# Add '''Pre Shared Key''' (a shared password used for authentication between the peers. The value of this field must match on both instances).
# Minimum Key complexity: Disabled
# Disable '''Minimum Key complexity'''.
# Local Identifier: IP Address
# Select '''Local Identifier Type''' (IP Address).
# Local Identifier: Cisco subnet IP address
# Write '''Local Identifier''' (Cisco LAN IP address).
# Local IP Type: Subnet
# Select '''Local IP Type''' (Subnet).
# IP Address: Local network
# Write '''IP Address''' (Cisco local network).
# Subnet Mask: Network Mask
# Add '''Subnet Mask''' (network mask).
# Remote Identifier Type: Remote WAN IP
# Select '''Remote Identifier Type''' (Remote WAN IP).
# Remote Identifier: 192.168.10.1
# Write '''Remote Identifier''' (RUT LAN IP).
# Remote IP Type: Subnet
# Select '''Remote IP Type''' (Subnet).
# IP Address: 192.168.10.0
# Add '''IP Address''' (RUT local network).
# Subnet Mask: 255.255.255.0
# Add '''Subnet Mask''' (RUT local network mask).
==Testing the setup==
==Testing the setup==
