Changes

<ul>

<ul>

     <li>Default Address (LAN IP): <b>192.168.{{#ifeq:{{{series}}}|TRB14x|2|1}}.1</b></li>

     <li>Default Address (LAN IP): <b>192.168.{{#switch:{{{series}}}|TRB14x|TRB5=2|#default=1}}.1</b></li>

     <li>Default Username: <b>admin</b></li>

     <li>Default Username: <b>admin</b></li>

     <li>Default Password: <b>admin01</b></li>

     <li>Default Password: <b>admin01</b></li>

     <li><b>Reboot the device</b>. If the reset button is pressed for up to 4 seconds, the device will reboot. Start of the reboot will be indicated by the flashing of all {{#ifeq: {{{series}}} | TRB2xx | 3 signal strength LEDs. | 5 signal strength LEDs together with the green connection status LED.}}</li>

     <li><b>Reboot the device</b>. If the reset button is pressed for up to 4 seconds, the device will reboot. Start of the reboot will be indicated by the flashing of all {{#ifeq: {{{series}}} | TRB2xx | 3 signal strength LEDs. | 5 signal strength LEDs together with the green connection status LED.}}</li>

     <li><b>Factory reset</b>. If the reset button is pressed for at least 5 seconds (by default), the device will perform a factory reset and reboot. Signal strength LEDs indicate the elapsed time while holding the reset button. When all {{#ifeq: {{{series}}} | TRB2xx | 3 | 5}} LEDs light up, it indicates that 5 seconds have passed and the reset button can be released. Start of the factory reset will be indicated by flashing of all {{#ifeq: {{{series}}} | TRB2xx | 3 signal strength LEDs. | 5 together with a red connection status LED.}}<br><b>NOTE</b>: the default button hold time value (5 seconds) can be changed in the {{#switch: {{{series}}}

     <li><b>Factory reset</b>. If the reset button is pressed for at least 5 seconds (by default), the device will perform a factory reset and reboot. Signal strength LEDs indicate the elapsed time while holding the reset button. When all {{#ifeq: {{{series}}} | TRB2xx | 3 | 5}} LEDs light up, it indicates that 5 seconds have passed and the reset button can be released. Start of the factory reset will be indicated by flashing of all {{#ifeq: {{{series}}} | TRB2xx | 3 signal strength LEDs. | 5 together with a red connection status LED.}}<br><b>NOTE</b>: the default button hold time value (5 seconds) can be changed in the {{#switch: {{{series}}}

| TRB14x = gateway

| TRB14x|TRB2xx|TRB5 = gateway

| TRB2xx = gateway

| router's}} WebUI, from the <b>System → Administration → [[{{{name}}}_Administration#General|General]]</b> page.</li>

| router's}} WebUI, from the <b>System → Administration → [[{{{name}}}_Administration#General|General]]</b> page.</li>

</ul>

</ul>

[[File:{{{file_webui}}}|border|class=tlt-border]]

[[File:{{{file_webui}}}|border|class=tlt-border]]

<!--==SMS-->

<!--==SMS-->

{{Template:Networking_device_manual_device_recovery_sms|name={{{name}}}|series={{{series}}}}}

 

      |{{Template:Networking_device_manual_device_recovery_sms|name={{{name}}}|series={{{series}}}}}

===Command line===

===Command line===

----

----

You can perform a factory reset via command line by executing the <b>{{#ifeq:{{{series}}}|TRB14x|factory_restore|firstboot}}</b> command. After this you will be asked to confirm the reset. If you're sure, type the letter <b>y</b> and press "Enter" or type the letter <b>n</b> if you wish to cancel the reset.

You can perform a factory reset via command line by executing the <b>firstboot</b> command. After this you will be asked to confirm the reset. If you're sure, type the letter <b>y</b> and press "Enter" or type the letter <b>n</b> if you wish to cancel the reset.

{{#ifeq:{{{series}}}|TRB14x||If you agreed to perform a factory reset, next type in <b>reboot</b> and press "Enter". }}The {{#ifeq: {{{series}}} | TRB2xx | gateway | router}} will be reset to it's factory settings and rebooted. The entire sequence of events should look like this:

If you agreed to perform a factory reset, next type in <b>reboot</b> and press "Enter". The {{#switch: {{{series}}} |TRB1xx|TRB2xx|TRB5=gateway|#default=router}} will be reset to it's factory settings and rebooted. The entire sequence of events should look like this:

{{Template: Networking_{{#ifeq:{{{series}}}|TRB14x|{{lc:{{{series}}}}}|rutxxx}}_manual_device_recovery_cli

{{Template: Networking_{{#ifeq:{{{series}}}|TRB14x|{{lc:{{{series}}}}}|rutxxx}}_manual_device_recovery_cli

}}

}}

You can find more information on the command line interface (CLI) <b>[[{{{name}}} CLI|here]]</b>.

  | You can find more information on the command line interface (CLI) <b>[[{{{name}}} CLI|here]]</b>.

{{#ifeq:{{{series}}} | TRB14x

{{#switch:{{{series}}}

  |

| RUT8xx|TRB14x|TRB5=

  | {{#ifeq:{{{name}}} | RUT850

| #default={{Template: Networking_device_manual_device_recovery_bootloader|name={{{name}}}|series={{{series}}}}}

      |  

      | {{#ifeq:{{{series}}} | RUTXxx

          | {{Template: Networking_device_manual_device_recovery_bootloader|name={{{name}}}|series={{{series}}}}}

    }}

}}

}}