157
edits
Changes
Template:Networking device manual unmanaged switch recovery troubleshooting (view source)
Revision as of 07:27, 27 April 2020
, 07:27, 27 April 2020→Connected devices has no internet
This chapter contains information of possible <b>recovery and troubleshooting</b> options for a {{{name}}} unmanaged switch.
This chapter contains information of possible <b>recovery and troubleshooting</b> options for a {{{name}}} unmanaged switch.
==Ethernet port LEDs not litting up==
==Ethernet port LEDs not lighting up==
==Connected devices has no internet==
<ol type="I">
<li>
<dl>
<dt>Issue</dt>
<dd>{{{name}}} <span style="color:green">green</span> Ethernet port LED is not lighting up (<span style="color:orange">orange</span> LED lit)</dd>
<dt>Solution</dt>
<dd>{{{name}}} switch <span style="color:green">green</span> Ethernet port LED indicates Gigabit connection with device. Check if connected device network card supports Gigabit speeds or software configuration is not limited to 10/100 Mbps.</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>{{{name}}} is not powered up</dd>
<dt>Solution</dt>
<dd>Check the front panel [https://wiki.teltonika-networks.com/view/{{{name}}}_LEDs#Power_LED power LED] if it is lit. If not, try to use other 7-57 VDC power supply, which can provide at least 2 W of power. More information about {{{name}}} powering options check [https://wiki.teltonika-networks.com/view/{{{name}}}_Powering_Options here]</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Connected device is not powered up</dd>
<dt>Solution</dt>
<dd>Check if connected device is powered up and working properly</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Bad cabling between {{{name}}} and connected device</dd>
<dt>Solution</dt>
<dd>Use other Ethernet cable to connect {{{name}}} with device</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Defected {{{name}}} Ethernet port</dd>
<dt>Solution</dt>
<dd>Use other free {{{name}}} Ethernet port to connect switch with device. If device establishes connection with {{{name}}} using other Ethernet port, {{{name}}} is defective and must be sent for service inspection and repairs. Check [[{{{name}}}_Device_Recovery_and_Troubleshooting_Options#RMA | RMA]] section for further instructions</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Defected {{{name}}} switch</dd>
<dt>Solution</dt>
<dd>If {{{name}}} Ethernet port LED are not lighting up after doing above mentioned actions, {{{name}}} is defective and must be sent for service inspection and repairs. Check [[{{{name}}}_Device_Recovery_and_Troubleshooting_Options#RMA | RMA]] section for further instructions</dd>
</dl>
</li>
</ol>
==Connected devices have no internet==
<ol type="1">
<ol type="I">
<li>Check cabling from router or modem to {{{name}}}. If link between devices is established Orange LED at connected Ethernet port port must be lit. More information about LED meaning is located [https://wiki.teltonika-networks.com/view/{{{name}}}_LEDs#Ethernet_port here]</li>
<li>
<li>Check cabling from connected device to {{{name}}}. If link between switch and connected device is established Orange LED at connected Ethernet port must be lit. More information about LED meaning is located [https://wiki.teltonika-networks.com/view/{{{name}}}_LEDs#Ethernet_port here]</li>
<dl>
<li>text</li>
<dt>Issue</dt>
<dd>Connected router/modem do not have internet connection</dd>
<dt>Solution</dt>
<dd>Check connected router/modem users manual how to diagnose and troubleshoot internet connection issue</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Bad cabling between {{{name}}} and router/modem</dd>
<dt>Solution</dt>
<dd>Check cabling from {{{name}}} to router/modem. If link between devices is established, <span style="color:orange">orange</span> LED at connected Ethernet port must be lit ([https://wiki.teltonika-networks.com/view/{{{name}}}_LEDs#Ethernet_port LEDs meaning]). If LED has not lit, change Ethernet cable, connect other router/modem and check again</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Bad cabling between {{{name}}} and connected device</dd>
<dt>Solution</dt>
<dd>Check cabling from {{{name}}} to connected device. If link between devices was established, <span style="color:orange">orange</span> LED at connected Ethernet port must be lit ([https://wiki.teltonika-networks.com/view/{{{name}}}_LEDs#Ethernet_port LEDs meaning]). If LED has not lit, change Ethernet cable and check again</dd>
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>Defected {{{name}}} switch</dd>
<dt>Solution</dt>
<dd>Connect device directly to router/modem and check if internet connection was established. If device gets access to internet, when directly connected to router/modem. Try turn switch off and on (restart), if issue persists, {{{name}}} is defective and must be sent for service inspection and repairs. Check [[{{{name}}}_Device_Recovery_and_Troubleshooting_Options#RMA | RMA]] section for further instructions</dd>
</dl>
</li>
</ol>
</ol>
==Connected devices not power via PoE==
==Connected device not powered via PoE==
<ol type="I">
<li>
<dl>
<dt>Issue</dt>
<dd>Connected device to {{{name}}} is not powered via PoE</dd>
<dt>Solution I</dt>
<dd>Check if connected device supports 802.3af and/or 802.3at PoE standard(s)</dd>
<dt>Solution II</dt>
<dd>Check if {{{name}}} is powered with PSU, which outputs 44 VDC or higher voltages and can provide at least 2 W + connected device needed power</dd>
<!--- <dt>Solution III</dt>
<dd>If using 10/100 Mbps connection, make sure that your cable has connected all wiring pairs</dd> --->
</dl>
</li>
<li>
<dl>
<dt>Issue</dt>
<dd>All PoE devices and switch lost power after connecting more than two device to {{{name}}}</dd>
<dt>Solution</dt>
<dd>{{{name}}} supports 802.3at standard, were each port can supply up to 30 W of power at PSE with total power budget of 120 W per all 4 ports. Standard PSU, which comes in the box with {{{name}}}, provides ~65 W power and limits power budget to ~60 W. If all connected devices to PoE ports combined required more that 60 W of power, PSU was overloaded and turned itself off.<br>If full 120 W power budget is necessary, {{{name}}} must be powered with PSU, which can provide at least 130 W power at 44 VDC or higher voltages</dd>
</dl>
</li>
</ol>
==RMA==
If conventional recovery methods do not help, you may need to send the device to warranty for repair. The warranty process is described <b>[https://teltonika-networks.com/warranty-repair/ here]</b>. --->
If conventional recovery methods do not help, you may need to send the device to warranty for repair. The warranty process is described <b>[https://teltonika-networks.com/warranty-repair/ here]</b>.
[[Category:{{{name}}} Manual]]
[[Category:{{{name}}} Manual]]
