Line 4: |
Line 4: |
| }} | | }} |
| ==Summary== | | ==Summary== |
− | This chapter is an overview of the Failover and Load Balancing functions in {{{name}}} routers.Template:Networking_rutos_manual_basic_advanced_webui_disclaimer | + | This chapter is an overview of the Failover and Load Balancing functions in {{{name}}} routers. |
| + | {{Template:Networking_rutos_manual_basic_advanced_webui_disclaimer}} |
| ===Failover=== | | ===Failover=== |
| ---- | | ---- |
Line 10: |
Line 11: |
| | | |
| In order to set priorities, simply press left mouse click on the interface, then drag it to the 1st, 2nd or other position and then press Save & Apply. | | In order to set priorities, simply press left mouse click on the interface, then drag it to the 1st, 2nd or other position and then press Save & Apply. |
| + | [[File:Networking_rutx11_manual_failover_confing_v1.png]] |
| + | |
| Below is an example of Failover settings section. | | Below is an example of Failover settings section. |
| + | |
| {{#switch: {{{name}}} | | {{#switch: {{{name}}} |
− | |RUTX11 = [[File:Networking_rutx11_manual_failover_confing_v1.png]] | + | |RUTX11 = [[File:Networking_rutx11_manual_failover_v1.png]] |
− | |RUTXR1 = [[File:Networking_rutx11_manual_failover_confing_v1.png]] | + | |RUTXR1 = [[File:Networking_rutx11_manual_failover_v1.png]] |
− | |RUTX12 = [[File:Networking_rutx11_manual_failover_confing_v1.png]] | + | |RUTX12 = [[File:Networking_rutx11_manual_failover_v1.png]] |
− | |RUTX10 = [[File:Networking_rutx10_manual_failover_confing_v1.png]] | + | |RUTX10 = [[File:Networking_rutx10_manual_failover_v1.png]] |
− | |RUTX09 = [[File:Networking_rutx09_manual_failover_confing_v1.png]] | + | |RUTX09 = [[File:Networking_rutx09_manual_failover_v1.png]] |
− | |RUTX08 = [[File:Networking_rutx08_manual_failover_confing_v1.png]] | + | |RUTX08 = [[File:Networking_rutx08_manual_failover_v1.png]] |
| }} | | }} |
| By pressing Edit button, you can find more Failover interface settings. More information and example are presented below. | | By pressing Edit button, you can find more Failover interface settings. More information and example are presented below. |
Line 72: |
Line 76: |
| |RUTXR1 = [[File:Networking_rutx11_manual_load_balancing_v1.png]] | | |RUTXR1 = [[File:Networking_rutx11_manual_load_balancing_v1.png]] |
| |RUTX12 = [[File:Networking_rutx11_manual_load_balancing_v1.png]] | | |RUTX12 = [[File:Networking_rutx11_manual_load_balancing_v1.png]] |
− | |RUTX10 = | + | |RUTX10 = [[File:Networking_rutx10_manual_load_balancing_v1.png]] |
− | |RUTX09 = | + | |RUTX09 = [[File:Networking_rutx09_manual_load_balancing_v1.png]] |
− | |RUTX08 = | + | |RUTX08 = [[File:Networking_rutx08_manual_load_balancing_v1.png]] |
| }} | | }} |
| | | |
| | | |
− | As you may notice from the image above, the configuration is very simple. You can assign ratio values to WAN interfaces. The ratio values represent a percentage of load that will go through an interface. For example, if you set that 3 parts of traffic would go through the Mobile interface and 2 parts would go through the Wired interface, it would mean that roughly 60% (3/5) of data will be transferred through Mobile, 40% (2/5) through Wired. If the ratios would be different, say Mobile: 5, Wired: 10, then 33% (5/15) of data would be transferred through Mobile, and 66% (10/15) would go through Wired. | + | As you may notice from the image above, the configuration is very simple. You can assign ratio values to WAN interfaces. The ratio values represent a percentage of load that will go through an interface. For example, if you set that 3 parts of traffic would go through the |
| + | {{#ifeq:{{mobile}} |
| + | Mobile |
| + | interface and 2 parts would go through the Wired interface, it would mean that roughly 60% (3/5) of data will be transferred through Mobile, 40% (2/5) through Wired. If the ratios would be different, say Mobile: 5, Wired: 10, then 33% (5/15) of data would be transferred through Mobile, and 66% (10/15) would go through Wired. |
| | | |
| If you press Edit button, you will be transferred to the same interface settings that were described in [[#Failover|Failover section]]. | | If you press Edit button, you will be transferred to the same interface settings that were described in [[#Failover|Failover section]]. |
| | | |
| [[Category:{{{name}}} Network section]] | | [[Category:{{{name}}} Network section]] |