Changes

Template:Networking rutos manual setup wizard (view source)

Revision as of 17:53, 16 December 2021

76 bytes removed ,  17:53, 16 December 2021
no edit summary
Line 1: Line 1:  
<!-- Template uses {{{name}}}, {{{series}}}, {{{mobile}}} (0), {{{wireless}}} (0)-->
 
<!-- Template uses {{{name}}}, {{{series}}}, {{{mobile}}} (0), {{{wireless}}} (0)-->
−
{{Template:Networking_rutos_manual_fw_disclosure
+
{{Template: Networking_rutos_manual_fw_disclosure
−
| fw_version = {{{series}}}_R_00.02.04.1
+
| fw_version ={{Template: Networking_rutos_manual_latest_fw
−
| series     = {{{series}}}
+
| series = {{{series}}}
 +
}}
 
}}
 
}}
−
 
+
{{#ifeq: {{{series}}} | RUT9 |<br><i><b>Note</b>: <b>[[{{{name}}} Setup Wizard (legacy WebUI)|click here]]</b> for the old style WebUI (FW version {{Template: Networking_rutos_manual_latest_fw | series = RUT9XX}} and earlier) user manual page.</i>|}}
 +
{{#ifeq: {{{series}}} | RUT2 |<br><i><b>Note</b>: <b>[[{{{name}}} Setup Wizard (legacy WebUI)|click here]]</b> for the old style WebUI (FW version {{Template: Networking_rutos_manual_latest_fw | series = RUT2XX}} and earlier) user manual page.</i>|}}
 
==Summary==
 
==Summary==
   Line 34: Line 36:  
</ul>
 
</ul>
   −
[[File:Networking_rutx_manual_setup_wizard_password_v1.png]]
+
[[File:Networking_rutos_manual_setup_wizard_set_new_password.png]]
    
After you have entered the new password, click 'Submit'. Afterwards you will be redirected to the first page of the Setup Wizard.
 
After you have entered the new password, click 'Submit'. Afterwards you will be redirected to the first page of the Setup Wizard.
   −
==Time==
+
==General==
   −
The <b>Time</b> section is used to configure the device's time settings.
+
The <b>General</b> section is used to configure the device's time and WebUI mode settings.
   −
[[File:Networking_rutx_manual_setup_wizard_general_v1.png]]
+
[[File:Networking_rutos_manual_setup_wizard_general.png|border|class=tlt-border]]
    
If you wish to set the device's time zone settings later instead, you can do so via the <i>Services → [[{{{name}}} NTP|NTP]]</i> page.
 
If you wish to set the device's time zone settings later instead, you can do so via the <i>Services → [[{{{name}}} NTP|NTP]]</i> page.
 +
 +
WebUI mode can be set in the <i>System → Administration → [[{{{name}}} Administration#General|General]]</i> page or by clicking the button under "Mode", which is located at the top-right corner of the WebUI:
 +
 +
[[File:Networking_{{lc:{{{series}}}}}_manual_webui_basic_advanced_mode.gif|border|class=tlt-border]]
    
==LAN==
 
==LAN==
Line 50: Line 56:  
The <b>LAN</b> section is used to configure the device's local area network (LAN) and DHCP server settings. A DHCP (Dynamic Host Configuration Protocol) server can automatically configure the TCP/IP settings for any device that requests such a service. If you connect a device that has been configured to obtain an IP address automatically, the DHCP server will lease out an IP address from the available IP pool and the device will be able to communicate within the device's private network.
 
The <b>LAN</b> section is used to configure the device's local area network (LAN) and DHCP server settings. A DHCP (Dynamic Host Configuration Protocol) server can automatically configure the TCP/IP settings for any device that requests such a service. If you connect a device that has been configured to obtain an IP address automatically, the DHCP server will lease out an IP address from the available IP pool and the device will be able to communicate within the device's private network.
   −
{{#ifeq:{{{series}}}|TRB14X|
+
[[File:Networking_rutos_manual_setup_wizard_lan_{{{lan}}}.png|border|class=tlt-border]]
−
[[File:Networking_trb1_manual_setup_wizard_lan_v1.png|border|class=tlt-border]] <!-- 192.168.2.1 -->
  −
|
  −
[[File:Networking_rutx_manual_setup_wizard_lan_v3.png|border|class=tlt-border]] <!-- 192.168.1.1 -->
  −
}}
      
<table class="nd-mantable">
 
<table class="nd-mantable">
Line 64: Line 66:  
     <tr>
 
     <tr>
 
         <td>IP address</td>
 
         <td>IP address</td>
−
         <td>ip; default: <b>{{#ifeq:{{{series}}}|TRB14X|192.168.2.1|192.168.1.1}}</b></td>
+
         <td>ip; default: <b>192.168.{{{lan}}}.1</b></td>
 
         <td>The LAN interface's IPv4 address. An IP address identifies a device on a network and allows it to communicate with other devices.</td>
 
         <td>The LAN interface's IPv4 address. An IP address identifies a device on a network and allows it to communicate with other devices.</td>
 
     </tr>
 
     </tr>
Line 74: Line 76:  
     <tr>
 
     <tr>
 
         <td>Enable DHCP</td>
 
         <td>Enable DHCP</td>
−
         <td>off {{!}} on; default: <b>on</b></td>
+
         <td>off | on; default: <b>on</b></td>
 
         <td>Turns the DHCP server on or off.</td>
 
         <td>Turns the DHCP server on or off.</td>
 
     </tr>
 
     </tr>
Line 94: Line 96:  
     <tr>
 
     <tr>
 
         <td>Units</td>
 
         <td>Units</td>
−
         <td>Hours {{!}} Minutes; default: <b>Hours</b></td>
+
         <td>Hours | Minutes; default: <b>Hours</b></td>
 
         <td>Lease time measuring units.</td>
 
         <td>Lease time measuring units.</td>
 
     </tr>
 
     </tr>
Line 100: Line 102:     
If you wish to set the device's LAN and DHCP settings later instead, you can do so via the <i>Network → [[{{{name}}} LAN|LAN]]</i> page.
 
If you wish to set the device's LAN and DHCP settings later instead, you can do so via the <i>Network → [[{{{name}}} LAN|LAN]]</i> page.
−
{{#ifeq:{{{mobile}}}|0||  
+
{{#ifeq: {{{mobile}}} | 1 |  
 
==Mobile==
 
==Mobile==
    
The <b>Mobile</b> section is used to configure the device's SIM card parameters.
 
The <b>Mobile</b> section is used to configure the device's SIM card parameters.
   −
[[File:Networking_rutx_manual_setup_wizard_wan_v3.png|border|class=tlt-border]]
+
[[File:Networking_rutos_manual_setup_wizard_mobile.png|border|class=tlt-border]]
    
<table class="nd-mantable">
 
<table class="nd-mantable">
Line 143: Line 145:     
If you wish to set the device's Mobile WAN settings later instead, you can do so via the <i>Network → [[{{{name}}} WAN|WAN]]</i> page.
 
If you wish to set the device's Mobile WAN settings later instead, you can do so via the <i>Network → [[{{{name}}} WAN|WAN]]</i> page.
−
}}
+
|}}
−
{{#ifeq:{{{wireless}}}|0||  
+
{{#ifeq: {{{wireless}}} | 1 |  
 
==WiFi==
 
==WiFi==
   −
The <b>WiFi</b> section is used to configure the device's WiFi access points (APs). The {{{name}}} supports two types of WiFi: 2.4 GHz and 5 GHz. 2.4 GHz WiFi provides better coverage and works at a longer range, but has lower data transfer speeds when compared to 5 GHz WiFi.
+
The <b>WiFi</b> section is used to configure the device's WiFi Access Point{{#ifeq:{{{wifi}}}|5|s|}} (AP{{#ifeq:{{{wifi}}}|5|s|}}). {{#ifeq:{{{wifi}}}|5|The {{{name}}} supports two types of WiFi: 2.4 GHz and 5 GHz. 2.4 GHz WiFi provides better coverage and works at a longer range, but has lower data transfer speeds when compared to 5 GHz WiFi.|}}
   −
[[File:Networking_rutx_manual_setup_wizard_wifi_v2.png|border|class=tlt-border]]
+
[[File:Networking_rutos_manual_setup_wizard_wifi_{{{wifi}}}.png|border|class=tlt-border]]
    
<table class="nd-mantable">
 
<table class="nd-mantable">
Line 163: Line 165:  
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
     <td>Channel</td>
+
     <td>ESSID</td>
−
         <td>WiFi channel number {{!}} auto; default: <b>auto</b></td>
+
         <td>string; default: <b>RUT_<last 4 symbols of WiFi MAC>{{#ifeq:{{{wifi}}}|5|_<frequency>|}}</b></td>
−
         <td>WiFi channel used by the access point. When this field is set to 'auto', the access point will choose the least populated channel.</td>
+
         <td>An identification string (name) for the access point. It is how the access point will be seen by connecting devices.</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
−
     <td>SSID</td>
+
     <td>Password</td>
−
         <td>string; default: <b>RUT_<last 4 symbols of WiFi MAC>_<frequency></b></td>
+
         <td>string; default: <b>unique to each device</b></td>
−
         <td>The Service Set Identifier (SSID) is an identification string (name) for the access point. It is how the access point will be seen by connecting devices.</td>
+
         <td>A password used to authenticate users to this access point.</td>
 
     </tr>
 
     </tr>
−
    <tr>
+
</table>
−
    <td>Encryption</td>
  −
        <td>No encryption {{!}} WPA-PSK {{!}} WPA2-PSK {{!}} WPA-PSK/WPA2-PSK Mixed Mode {{!}} WPA-EAP {{!}} WPA2-EAP; default: <b>WPA2-PSK</b></td>
  −
        <td>The type of encryption used by the access point.</td>
  −
    </tr>
  −
    <tr>
  −
    <td>Cipher</td>
  −
        <td>auto {{!}} Force CCMP (AES) {{!}} Force TKIP {{!}} Force TKIP and CCMP (AES); default: <b>Force TKIP and CCMP (AES)</b></td>
  −
        <td>An algorithm for performing encryption and decryption.</td>
  −
    </tr>
  −
    <tr>
  −
    <td>Key</td>
  −
        <td>string; default: <b>unique to each device</b></td>
  −
        <td>A password used to authenticate users to the access point.</td>
  −
    </tr></table>
      
If you wish to set the device's WiFi settings later instead, you can do so via the <i>Network → [[{{{name}}} Wireless|Wireless]]</i> page.
 
If you wish to set the device's WiFi settings later instead, you can do so via the <i>Network → [[{{{name}}} Wireless|Wireless]]</i> page.
−
}}
+
|}}
−
 
   
==RMS==
 
==RMS==
   Line 197: Line 184:  
In order to add a device(s) to RMS, get yourself acquainted by watching [https://www.youtube.com/watch?v=bZeqdrAcdVU this instructional video] and register an account by [https://rms.teltonika.lt/ clicking here]. <b>Each unique device receives a free month-long RMS license</b> when added to RMS for the first time.  
 
In order to add a device(s) to RMS, get yourself acquainted by watching [https://www.youtube.com/watch?v=bZeqdrAcdVU this instructional video] and register an account by [https://rms.teltonika.lt/ clicking here]. <b>Each unique device receives a free month-long RMS license</b> when added to RMS for the first time.  
   −
{{#ifeq:{{{series}}}|RUTX|
+
[[File:Networking_rutos_manual_setup_wizard_rms_{{{rms}}}_v2.png|border|class=tlt-border]]
−
[[File:Networking_rutx_manual_setup_wizard_rms_v2.png]]
  −
|
  −
[[File:Networking_trb1_manual_setup_wizard_rms_v1.png|border|class=tlt-border]]
  −
}}
      
<table class="nd-mantable">
 
<table class="nd-mantable">
Line 211: Line 194:  
     <tr>
 
     <tr>
 
         <td>Connection type</td>
 
         <td>Connection type</td>
−
         <td>Enabled {{!}} Standby {{!}} Disabled; default: <b>Enabled</b></td>
+
         <td>Enabled | Standby | Disabled; default: <b>Enabled</b></td>
 
         <td>Defines how the device will connect to RMS:
 
         <td>Defines how the device will connect to RMS:
 
             <ul>
 
             <ul>
Line 222: Line 205:  
     <tr>
 
     <tr>
 
         <td>Hostname</td>
 
         <td>Hostname</td>
−
         <td>host {{!}} ip; default: <b>rms.teltonika.lt</b></td>
+
         <td>host | ip; default: <b>rms.teltonika.lt</b></td>
 
         <td>Address of the RMS server. If you're using regular RMS, just leave the default address (<i>rms.teltonika.lt</i>).</td>
 
         <td>Address of the RMS server. If you're using regular RMS, just leave the default address (<i>rms.teltonika.lt</i>).</td>
 
     </tr>
 
     </tr>
Retrieved from "https://wiki.teltonika-networks.com/view/Special:MobileDiff/66113...86592"

Navigation menu