Template:Networking rutos manual wan
Template:Networking rutos manual fw disclosure
Summary
The WAN page is used to to set up network interfaces WAN network interfaces which are
This manual page provides an overview of the WAN windows in {{{name}}} devices.
If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.
Network Interfaces
The WAN section displays interfaces currently existing on this device.
{{#ifeq: {{{series}}} | RUTX
| [[File:Networking_rutos_manual_wan_modem_{{{modem}}}_v1.png|border|class=tlt-border]]
| [[File:Networking_{{{series}}}_manual_wan_v1.png
Interface configuration
This section provides information on WAN interface configuration. There is {{{no_of_if}}} type of WAN interface on the device:
To begin configuring an interface, click the 'Edit' button on the right side of the interface:
Wired WAN
This section covers all parameters directly related to a wired (Ethernet) WAN interface.
General Setup
The General Setup section is used to configure the protocol and all the different parameters that go along with each protocol. This section is different for each protocol.
General Setup: Static address
The static address protocol uses a predefined manual configuration instead of obtaining parameters automatically via a DHCP lease.
File:Networking rutos manual wan wan configuration general setup static address v1.png
| Field | Value | Description |
|---|---|---|
| IPv4 address | ip4; default[for LAN]: 192.168.1.1 | The IPv4 address interface of this interface. An IP address identifies a device on a network and allows it to communicate with other devices. |
| IPv4 netmask | netmask; default[for LAN]: 255.255.255.0 | The IPv4 netmask of this interface. A netmask is used to define how "large" a network is by specifying which part of the IP address denotes the network and which part denotes a device. |
| DNS servers | ip4; default: none | DNS server addresses that this interface will use. If left empty, DNS servers are assigned automatically. To see what DNS servers are currently used, you can check the contents of the /tmp/resolv.conf.auto file. |
General Setup: DHCP client
The DHCP client protocol is used to set up an interface which obtains its configuration parameters automatically via a DHCP lease.
File:Networking rutos manual wan wan configuration general setup dhcp client v1.png
| Field | Value | Description |
|---|---|---|
| Hostname to send when requesting DHCP | string; default: none | A hostname for this interface used to identify this machine on the DHCP server. |
General Setup: DHCPv6 client
The DHCPv6 client protocol is used to set up an IPv6 interface which obtains its configuration parameters automatically via a DHCP lease.
File:Networking rutos manual wan wan configuration general setup dhcpv6 client v1.png
| Field | Value | Description |
|---|---|---|
| Request IPv6-address | try | force | disabled; default: try | Defines the behaviour for requesting an address. |
| Request IPv6-prefix of length | integer [0..64] | Automatic | disabled ; default: Automatic | Defines how this will request a IPv6 ULA-Prefix length. If set to 'disabled' the interface will obtain a single IPv6 address without a subnet for routing. |
General Setup: PPPoE
The PPPoE protocol is used to set up a PPP (Point-to-Point Protocol) connection over the Ethernet port.
File:Networking rutos manual wan wan configuration general setup pppoe v1.png
| Field | Value | Description |
|---|---|---|
| PAP/CHAP username | string; default: none | Username used in PAP/CHAP authentication. |
| PAP/CHAP password | string; default: none | Password used in PAP/CHAP authentication. |
Advanced Settings
The Advanced Settings section is used to set up some of the more specific and less frequently used interface parameters. This section is different for each protocol.
Advanced Settings: Static address
Advanced Settings information for Static protocol is provided in the table below.
File:Networking rutos manual wan wan configuration advanced settings static address v1.png
| Field | Value | Description |
|---|---|---|
| Override MAC address | mac; default: none | When set, uses a user-defined MAC address for the interface. |
| Override MTU | integer [1..9200]; default: none | Changes the interface's allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction. |
| Use gateway metric | integer; default: none | A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority). |
Advanced Settings: DHCP client
Advanced Settings information for DHCP protocol is provided in the table below.
File:Networking rutos manual wan wan configuration advanced settings dhcp client v1.png
| Field | Value | Description |
|---|---|---|
| Use DNS servers advertised by peer | off | on; default: on | Specifies whether to use DNS servers obtained automatically or specified manually. |
| Use custom DNS servers | off | on; default: on | Specifies whether to use DNS servers obtained automatically or specified manually. Note: this field only becomes visible when Use DNS servers advertised by peer is set to off |
| Use gateway metric | integer; default: none | A metric specifies the priority of the gateway. The lower the metric, the higher the priority (0 for highest priority). |
| Override MAC address | mac; default: none | Override MAC address of the WAN interface. For example, your ISP (Internet Service Provider) gives you a static IP address and it might also bind it to your computers MAC address (i.e., that IP will only work with your computer but not with your device). In this field you can enter your computer’s MAC address and fool the gateway in to thinking that it is communicating with your computer. |
| Override MTU | integer [1..9200]; default: none | Changes the interfaces allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction. |
Advanced Settings: DHCPv6 client
Advanced Settings information for DHCPv6 protocol is provided in the table below.
File:Networking rutos manual wan wan configuration advanced settings dhcpv6 client v1.png
| Field | Value | Description |
|---|---|---|
| Use DNS servers advertised by peer | off | on; default: on | Specifies whether to use DNS servers obtained automatically or specified manually. |
| Use custom DNS servers | off | on; default: on | Specifies whether to use DNS servers obtained automatically or specified manually. Note: this field only becomes visible when Use DNS servers advertised by peer is set to off |
| Override MAC address | mac; default: none | When set, uses a user-defined MAC address for the interface. |
| Override MTU | integer [1..9200]; default: none | Changes the interface's allowed maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction. |
Advanced Settings: PPPoE
Advanced Settings information for PPPoE protocol is provided in the table below.
File:Networking rutos manual wan wan configuration advanced settings pppoe v1.png
| Field | Value | Description |
|---|---|---|
| Obtain IPv6 address | Automatic | Disabled | Manual; default: Automatic | Defines behaviour for obtaining an IPv6 address. |
| Use DNS servers advertised by peer | off | on; default: on | Specifies whether to use DNS servers obtained automatically or specified manually. |
| Use custom DNS servers | off | on; default: on | Specifies whether to use DNS servers obtained automatically or specified manually. Note: this field only becomes visible when Use DNS servers advertised by peer is set to off |
| Override MTU | integer [1..1500]; default: none | Maximum Transmission Unit (MTU) – specifies the largest possible size of a data packet. |
DHCP Server: IPv6 Settings
Refer to the table below for information on the IPv6 Settings section.
[[File::Networking_rutos_manual_wan_wan_configuration_dhcp_server_ipv6_settings_v1.png|border|class=tlt-border]]
| Field | Value | Description |
|---|---|---|
| Router Advertisement-Service | disabled | relay mode | server mode | hybrid mode; default: Disabled | Specifies whether router advertisements should be enabled (server mode), relayed or disabled. |
| DHCPv6-Service | disabled | relay mode | server mode | hybrid mode; default: Disabled | Specifies whether DHCPv6 server should be enabled (server), relayed (relay) or disabled (disabled). |
| NDP Proxy | disabled | relay mode | hybrid mode; default: Disabled | Specifies whether NDP should be relayed or disabled. |
| Announced DNS server | ip; default: none | Supplements DHCP-assigned DNS server entries with ones specified in this field. |
| Announced DNS domains | ip; default: none | DNS domain handed out to DHCP clients. |
hour [1..24]; default: hour 0 Specifies when the period of counting data usage should begin. After the period is over, the limit is reset and the count begins over again. Enable SMS warning off | on; default: off Turns SMS warning on or off. When turned on and configured, sends an SMS message to a specified number after the SIM card uses a specified amount of data. Data limit* (MB) integer; default: none The received data limit before sending an SMS warning. After reaching using the the amount of data specified in this field, the router will send an SMS warning message to the specified phone number. Phone number phone number; default: none Recipient's phone numbers.
[[Category:{{{name}}} Network section]]
