Changes

}}}}

}}}}

==SSIDs==

==Wireless ==

{{#switch: {{{wifi}}}

{{#switch: {{{wifi}}}

}}

}}

==={{#switch:{{{series}}}|TAP100|TAP200=SSIDS|#default=WiFi 2.4 GHz}} {{#switch:{{{series}}}|TAP100|TAP200=|#default={{#ifeq:{{{wifi}}}|5|& 5 GHz|}}}}===

===SSIDS===

 

The <b>{{#switch:{{{series}}}|TAP100|TAP200=SSIDS|#default=WiFi 2.4 GHz}} {{#switch:{{{series}}}|TAP100|TAP200=|#default={{#ifeq:{{{wifi}}}|5|& 5 GHz|}}}}</b> section is used to configure your wireless access points (AP) and wireless clients (STA).

The <b>SSIDs</b> section is used to configure your wireless access points (AP) and wireless clients (STA).

{{#switch:{{{name}}}

{{#switch:{{{name}}}

}}

}}

Above is the overview of the {{#switch:{{{series}}}|TAP100|TAP200=SSIDS|#default=Wireless}} Overview window. It displays active access points{{#switch:{{{series}}}|TAP100|TAP200=.|#default=  and stations.}}  

Above is the overview of the SSIDS Overview window. It displays active access points{{#switch:{{{series}}}|TAP100|TAP200=.|#default=  and stations.}}  

Here you can turn on or off your WiFi interfaces, remove them or start configuring by clicking on  

Here you can turn on or off your WiFi interfaces, remove them or start configuring by clicking on  

[[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button on the right side of interface.{{#switch:{{{series}}}|TAP100|TAP200=|#default=  You can also configure your WiFi devices by clicking [[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button in the right side of each table header. To configure your Wireless device as Client press '''Scan''' button to scan the surrounding area and attempt to connect to a new wireless access point.}}

[[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button on the right side of interface.{{#switch:{{{series}}}|TAP100|TAP200=|#default=  You can also configure your WiFi devices by clicking [[File:Networking rutx manual edit button v1.png]] <b>Edit</b> button in the right side of each table header. To configure your Wireless device as Client press '''Scan''' button to scan the surrounding area and attempt to connect to a new wireless access point.}}

|}}

|}}

===={{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings====

{{#switch:{{{series}}}|TAP100|TAP200= ===Radio Settings===|#default= ====Global Settings====}}

The <b>{{#ifeq:{{{series}}}|TAP100|Radio|Global}} Settings</b> section is used for configuring WiFi hardware parameters. You can find this section {{#ifeq:{{{series}}}|TAP100||by clicking the 'Edit' button next to a wireless device (<u>not an interface</u>)}} in the Network → {{#ifeq:{{{series}}}|TAP100|Radio page.|Wireless page:}}

The <b>{{#switch:{{{series}}}|TAP100|TAP200=Radio|#default=Global}} Settings</b> section is used for configuring WiFi hardware parameters. You can find this section {{#switch:{{{series}}}|TAP100|TAP200=|#default=by clicking the 'Edit' button next to a wireless device (<u>not an interface</u>)}} in the Network → {{#switch:{{{series}}}|TAP100|TAP200=Radio page.|#default=SSIDS page:}}

{{#switch:{{{name}}}

{{#switch:{{{name}}}

|TAP100 =

|TAP100 =

}}

}}

=====General Setup=====

{{#switch:{{{series}}}|TAP100|TAP200= ====General Setup====|#default= =====General Setup=====}}

 

The <b>General Setup</b> section is used to turn a wireless device on or off, select the operating frequency (WiFi mode and channel), transmit power and define a country code.  

The <b>General Setup</b> section is used to turn a wireless device on or off, select the operating frequency (WiFi mode and channel), transmit power and define a country code.