Template:Networking rutxxx manual vpn dmvpn

From Teltonika Networks Wiki
Revision as of 14:43, 8 July 2019 by Dziugas (talk | contribs) (Created page with "==DMVPN== <b>Dynamic Multipoint VPN</b> (<b>DMVPN</b>) is a method of building scalable IPsec VPNs. DMVPN is configured as a hub-and-spoke network, where tunnels between spok...")

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)

DMVPN

Dynamic Multipoint VPN (DMVPN) is a method of building scalable IPsec VPNs. DMVPN is configured as a hub-and-spoke network, where tunnels between spokes are built dynamically; therefore, no change in configuration is required on the hub in order to connect new spokes.

DMVPN configuration


To create a new DMVPN instance, go to the Services → VPN → DMVPN section, enter a custom name and click the 'Add' button. A DMVPN instance with the given name will appear in the "DMVPN Configuration" list.

To begin configuration, click the 'Edit' button located next to the instance. Refer to the figures and tables below for information on the DMVPN instance configuration:

[[File:{{{file_dmvpn_config}}}]]

Field Value Description
Enabled yes | no; default: no Turns the DMVPN instance on or off.
Working mode Spoke | Hub; default: Spoke Selects the role of this instance
  • Hub - the central instance of DMVPN that connects other peers (spokes) into single network. There is no need to reconfigure the hub when connecting new spokes to it.
  • Spoke - an instance that connects to the hub.
Hub address ip | host; default: off IP address or hostname of a DMVPN hub.



[[File:{{{file_dmvpn_gre_config}}}]]

Field Value Description
Tunnel source network interface; default: none Network interface used to establish the GRE Tunnel.
Local GRE interface IP address ip; default: none IP address of the local GRE Tunnel network interface.
Spoke: Remote GRE interface IP address ip; default: none IP address of the remote GRE Tunnel instance.
Hub: Local GRE interface netmask netmask; default: none Subnet mask of the local GRE Tunnel network interface.
GRE MTU integer; default: 1476 Sets the maximum transmission unit (MTU) size. It is the largest size of a protocol data unit (PDU) that can be transmitted in a single network layer transaction.
GRE keys integer [0..65535]; default: none A key used to identify incoming and outgoing GRE packets.



[[File:{{{file_dmvpn_ipsec_config}}}]]

Field Value Description
Negotiation mode Main | Aggressive; default: Main Internet Security and Key Management Protocol (ISAKMP) phase 1 exchange mode.
  • Main - performs three two-way exchanges between the initiator and the receiver (a total of 9 messages).
  • Aggressive - performs fewer exchanges than main mode (a total of 6 messages) by storing most data into the first exchange. In aggressive mode, the information is exchanged before there is a secure channel, making it less secure but faster than main mode.
My identifier type FQDN | User FQDN | Address; default: FQDN Defines the type of identity used in user (IPsec instance) authentication.
  • FQDN - identity defined by fully qualified domain name. It is the complete domain name for a host (for example, something.somedomain.com). Only supported with IKEv2.
  • User FQDN - identity defined by fully qualified username string (for example, [email protected]). Only supported with IKEv2.
  • Address - identity by IP address.
My identifier ip | string; default: none Defines how the user (IPsec instance) will be identified during authentication.
Encryption algorithm DES | 3DES | AES128 | AES192 | AES256; default: 3DES Algorithm used for data encryption.
Authentication/Hash algorithm MD5 | SHA1 | SHA256 | SHA384 | SHA512; default: SHA1 Algorithm used for exchanging authentication and hash information.
DH group/PFS group MODP768 | MODP1024 | MODP1536 | MODP2048 | MODP3072 | MODP4096; default: MODP1536
Lifetime integer; default: 8 hours Defines a time period after which the phase will re-initiate its exchange of information.
Pre shared key string; default: none A shared password used for authentication between IPsec peers.
Secret's ID selector string; default: none Each secret can be preceded by a list of optional ID selectors. A selector is an IP address, a Fully Qualified Domain Name, user@FQDN or %any.
NOTE: IKEv1 only supports IP address ID selector.



[[File:{{{file_dmvpn_nhrp_config}}}]]

Field Value Description
NHRP network ID integer; default: 1 An identifier used to define the NHRP domain. This is a local parameter and its value does not need to match the values specified on other domains. However, the NHRP ID is added to packets which arrive on the GRE interface; therefore, it may be helpful to use the same ID for troubleshooting purposes.
NHRP hold time integer; default: 7200 Specifies the holding time for NHRP Registration Requests and Resolution Replies sent from this interface or shortcut-target. The hold time is specified in seconds and defaults to two hours.