Difference between revisions of "Template:Networking trb manual powering options"

From Teltonika Networks Wiki
Line 1: Line 1:
 
This chapter contains information on <b>powering options</b> supported by {{{name}}} devices.
 
This chapter contains information on <b>powering options</b> supported by {{{name}}} devices.
 
__TOC__
 
__TOC__
−
{{Template: networking_device_manual_powering_options_power_socket
+
 
−
| name  = {{{name}}}
+
==Power socket==
−
| series = {{{series}}}
+
 
−
}}
+
The {{{name}}} device can be powered over the {{{pin}}} connector using a {{{volts}}} power supply unit (PSU). Refer to the image below for the power socket pinout information:
−
{{#ifeq: {{{eth}}} | 1 | {{Template: networking_device_manual_powering_options_passive_poe
+
 
−
| series    = {{{series}}}
+
[[File:Networking_rutos_manual_powering_options_{{{pin}}}.png]]
−
| file_lan1 = {{{file_lan1}}}
+
 
−
| size_lan1 = {{{size_lan1}}}}}
+
If you decide not to use the standard {{{psu}}} PSU and want to power the device from a higher voltage, please make sure that you choose a power supply of high quality. Some power supplies can produce voltage peaks significantly higher than the declared output voltage, especially during connection and disconnection.
−
|}}
+
 
−
{{#ifeq: {{{eth}}} | 1 | {{Template: networking_device_manual_powering_options_simultaneous_powering}}|}}
+
While the device is designed to accept input voltage in the range of {{{volts}}}, high voltage power supplies can harm the device. If you want to use high voltage power supplies it is recommended to also use additional safety equipment to suppress voltage peaks from the power supply.
 +
 
 +
{{#ifeq: {{{eth}}} | 1 | <h2>Passive PoE</h2>
 +
 
 +
The device may also be powered by an Ethernet cable via the <> port:<br>
 +
 
 +
[[File:{{{file_lan1}}}|{{{size_lan1}}}px]]
 +
 
 +
<font size="-1">
 +
<ul>
 +
{{#ifeq: {{{name}}} | TRB140 |<li>TRB140 devices support PPoE from HW revision 0007</li>|}}
 +
    <li>The device is <b>NOT COMPLIANT</b> with the IEEE 802.3af-2003 standard: powering the device from an IEEE 802.3af-2003 power supply <b>will damage the device</b> as it is not rated for input voltages of the PoE standard.</li>
 +
    <li>The device is <b>NOT COMPLIANT</b> with the IEEE 802.3at standard: it cannot power other devices over Ethernet.</li>
 +
</ul>
 +
</font>
 +
 
 +
{{Template: Networking_device_manual_powering_options_passive_poe_table}}
 +
 
 +
<h3>Simultaneous powering</h3>
 +
----
 +
The device can be powered from the power socket and over Ethernet simultaneously. The power socket has higher priority meaning that the device will draw power from the power socket as long as it is available.
 +
 
 +
When the device is switching from one power source to another it loses power for a fraction of a second and may reboot. The device will function correctly after the reboot.|}}
 
{{#ifeq: {{{rs485}}} | 1 | <h2>RS485</h2>
 
{{#ifeq: {{{rs485}}} | 1 | <h2>RS485</h2>
 
You can also power the device over the RS485 connector. In order to do so, follow the steps described below.
 
You can also power the device over the RS485 connector. In order to do so, follow the steps described below.
−
 
 
<ul>
 
<ul>
 
     <li>Unscrew the two hex bolts and remove the back panel.<br>[[File:Networking_trb145_manual_powering_options_rs485_unscrew_hex_bolts.png|300px]]</li>
 
     <li>Unscrew the two hex bolts and remove the back panel.<br>[[File:Networking_trb145_manual_powering_options_rs485_unscrew_hex_bolts.png|300px]]</li>

Revision as of 10:28, 2 September 2020

This chapter contains information on powering options supported by {{{name}}} devices.

Power socket

The {{{name}}} device can be powered over the {{{pin}}} connector using a {{{volts}}} power supply unit (PSU). Refer to the image below for the power socket pinout information:

[[File:Networking_rutos_manual_powering_options_{{{pin}}}.png]]

If you decide not to use the standard {{{psu}}} PSU and want to power the device from a higher voltage, please make sure that you choose a power supply of high quality. Some power supplies can produce voltage peaks significantly higher than the declared output voltage, especially during connection and disconnection.

While the device is designed to accept input voltage in the range of {{{volts}}}, high voltage power supplies can harm the device. If you want to use high voltage power supplies it is recommended to also use additional safety equipment to suppress voltage peaks from the power supply.


[[Category:{{{name}}} Manual]]

Retrieved from "https://wiki.teltonika-networks.com/index.php?title=Template:Networking_trb_manual_powering_options&oldid=71289"