Template:Networking rutos manual setup wizard
Template:Networking rutos manual fw disclosure
Summary
The Setup Wizard is a tool that offers a simplified version of other WebUI pages used to set some of the most relevant device parameters:
- [[{{{name}}} NTP|Time]]
- [[{{{name}}} LAN|LAN]]
- [[{{{name}}} WAN|WAN]]
- [[{{{name}}} Wireless|WiFi]]
- [[{{{name}}}_Cloud_Solutions#RMS|RMS]]
You will be greeted with the Setup Wizard the first time you login, after you have changed the device default password. On other logins you will be redirected to the [[{{{name}}} Overview|Overview]] page, but you can reach the Setup Wizard any time via the System → Setup Wizard page.
This page is an overview of the Setup Wizard tool for {{{name}}} devices.
Set new password
On your very first login you will be required to change the device default password. This is done for safety reasons. In many cases devices are used to provide access to remote networks and systems. Since many manufacturers use similar default passwords (like admin, admin01, admin123, etc.) it is easy for attackers to gain access to devices that use such passwords and compromise the systems behind them. Therefore, to avoid such malicious attacks, this step is mandatory and you will not able to access the rest of the WebUI before you change the password.
The new password must contain:
- 8-32 characters;
- at least one upper case letter;
- at least one lower case letter;
- at least one digit.
After you have entered the new password, click 'Submit'. Afterwards you will be redirected to the first page of the Setup Wizard.
General
The General section is used to configure the device's time and WebUI mode settings.
If you wish to set the device's time zone settings later instead, you can do so via the Services → [[{{{name}}} NTP|NTP]] page.
WebUI mode can be set in the System → Administration → [[{{{name}}} Administration#General|General]] page or by clicking the button under "Mode", which is located at the top-right corner of the WebUI:
[[File:Networking_{{{series}}}_manual_webui_basic_advanced_mode.gif|border|class=tlt-border]]
LAN
The LAN section is used to configure the device's local area network (LAN) and DHCP server settings. A DHCP (Dynamic Host Configuration Protocol) server can automatically configure the TCP/IP settings for any device that requests such a service. If you connect a device that has been configured to obtain an IP address automatically, the DHCP server will lease out an IP address from the available IP pool and the device will be able to communicate within the device's private network.
[[File:Networking_rutos_manual_setup_wizard_lan_{{{lan}}}.png|border|class=tlt-border]]
| Field | Value | Description |
|---|---|---|
| IP address | ip; default: 192.168.{{{lan}}}.1 | The LAN interface's IPv4 address. An IP address identifies a device on a network and allows it to communicate with other devices. |
| Netmask | netmask; default: 255.255.255.0 | A netmask is used to define how "large" a network is by specifying which part of the IP address denotes the network and which part denotes the device. |
| Enable DHCP | off | on; default: on | Turns the DHCP server on or off. |
| Start | integer [1..255]; default: 100 | The starting IP address value. e.g., if your device's LAN IP is 192.168.1.1 and your subnet mask is 255.255.255.0 that means that in your network a valid IP address has to be in the range of [192.168.1.0..192.168.1.254] (192.168.1.255 is a special unavailable address). If the Start value is set to 100 then the DHCP server will only lease out addresses starting from 192.168.1.100. |
| Limit | integer [1..255]; default: 150 | How many addresses the DHCP server can lease out. Continuing from the example above: if the start address is 192.168.1.100 and the server can lease out 150 addresses, available addresses will be from 192.168.1.100 to 192.168.1.249 (100 + 150 – 1 = 249; this is because the first address is inclusive). |
| Lease time | interger [2..999999]; default: 12 | A DHCP lease will expire after the amount of time specified in this field and the device that was using the lease will have to request a new one. However, if the device stays connected, its lease will be renewed after half of the specified amount of time passes (e.g., if lease time is 12 hours, then every 6 hours the device will ask the DHCP server to renew its lease). The minimal amount of time that can be specified is 2 minutes. |
| Units | Hours | Minutes; default: Hours | Lease time measuring units. |
If you wish to set the device's LAN and DHCP settings later instead, you can do so via the Network → [[{{{name}}} LAN|LAN]] page.
RMS
This section is used to configure the settings required to connect the device to the RMS (Remote Management System) - a cloud system designed by Teltonika and intended for remote monitoring and management of Teltonika-Networks products.
In order to add a device(s) to RMS, get yourself acquainted by watching this instructional video and register an account by clicking here. Each unique device receives a free month-long RMS license when added to RMS for the first time.
[[File:Networking_rutos_manual_setup_wizard_rms_{{{rms}}}.png|border|class=tlt-border]]
| Field | Value | Description |
|---|---|---|
| Connection type | Enabled | Standby | Disabled; default: Enabled | Defines how the device will connect to RMS:
|
| Hostname | host | ip; default: rms.teltonika.lt | Address of the RMS server. If you're using regular RMS, just leave the default address (rms.teltonika.lt). |
| Port | integer [0..65535]; default: 15009 | Port number for connecting to RMS. If you're using regular RMS, just leave the default port (15009). |
If you wish to set the device's RMS settings later instead, you can do so via the Services → Cloud Solutions → [[{{{name}}}_Cloud_Solutions#RMS|RMS]] page.
[[Category:{{{name}}} System section]]