Difference between revisions of "Modbus TCP Master MQTT Gateway"

From Teltonika Networks Wiki
m (Almost final)
Line 1: Line 1:
 +
__TOC__
 
==Summary==
 
==Summary==
 
In this guide Modbus TCP master MQTT Gateway function will be configured with two different types of MQTT Brokers. First using third party MQTT Broker services (in this example ''Flespi.io''). Second using RUT240 router as MQTT Broker. Two RUT955 routers will be used as Modbus TCP Master and Slave, and PC acts as MQTT Publisher and Subscriber.
 
In this guide Modbus TCP master MQTT Gateway function will be configured with two different types of MQTT Brokers. First using third party MQTT Broker services (in this example ''Flespi.io''). Second using RUT240 router as MQTT Broker. Two RUT955 routers will be used as Modbus TCP Master and Slave, and PC acts as MQTT Publisher and Subscriber.
Line 6: Line 7:
  
 
===Configuring RUT955 Modbus TCP Slave ===
 
===Configuring RUT955 Modbus TCP Slave ===
 +
----
 
Go to '''Services > Modbus > Modbus TCP Slave''':
 
Go to '''Services > Modbus > Modbus TCP Slave''':
  
 
#Check '''Enable'''
 
#Check '''Enable'''
# Enter port that will be used, in this example 502 will be used
+
#Enter port that will be used, in this example 502 will be used
# Enter device ID
+
#Enter device ID
 
#Press '''Save & Apply'''
 
#Press '''Save & Apply'''
[[File:Networking_MQTT_MODBUS_flespi_configuration_slave1_v1.png|alt=|border|1120x1120px]]
+
[[File:Networking_MQTT_MODBUS_flespi_configuration_slave1_v1.png|border|class=tlt-border|1120x1120px]]
  
 
''*In this config LAN port is used so “Allow Remote Access” is not needed''
 
''*In this config LAN port is used so “Allow Remote Access” is not needed''
Line 18: Line 20:
 
''Modbus TCP Slave RUT955 is now configured''.
 
''Modbus TCP Slave RUT955 is now configured''.
  
===Configuring RUT955 Modbus TCP Master ===
+
===Configuring RUT955 Modbus TCP Master===
 +
----
 
Go to '''Services > Modbus > Modbus TCP Master'''
 
Go to '''Services > Modbus > Modbus TCP Master'''
  
 
#Press '''Add'''
 
#Press '''Add'''
 
#Check '''Enable'''
 
#Check '''Enable'''
# Enter name for slave device
+
#Enter name for slave device
# Slave ID must match with previously configured Slave device ID
+
#Slave ID must match with previously configured Slave device ID
 
#Enter IP address of Modbus TCP Slave device
 
#Enter IP address of Modbus TCP Slave device
 
#Chose same Port as in Slave device - 502
 
#Chose same Port as in Slave device - 502
#Enter Period in seconds, how often requests will be sent to Slave device
+
# Enter Period in seconds, how often requests will be sent to Slave device
 
#Enter new request name and press '''Add''' in Requests configurations
 
#Enter new request name and press '''Add''' in Requests configurations
 
#Choose Data type and Function, enter First register/coil/input to be read or written and Register count. You can name each individual configuration, and then select enable on configurations that you want to use. In this example, register to get WAN IP address of the slave device is used.
 
#Choose Data type and Function, enter First register/coil/input to be read or written and Register count. You can name each individual configuration, and then select enable on configurations that you want to use. In this example, register to get WAN IP address of the slave device is used.
Line 35: Line 38:
  
 
===Configuring Flespi.io MQTT Broker===
 
===Configuring Flespi.io MQTT Broker===
 +
----
 
Login or create an account on https://flespi.io
 
Login or create an account on https://flespi.io
  
Line 52: Line 56:
  
 
===Configuring MQTT Gateway on RUT955 Modbus TCP Master===
 
===Configuring MQTT Gateway on RUT955 Modbus TCP Master===
 +
----
 
Open routers WebUI and navigate to Services > Modbus > MQTT Gateway
 
Open routers WebUI and navigate to Services > Modbus > MQTT Gateway
  
# Select Enable
+
#Select Enable
 
#Enter Host (copied from flespi connection settings without 'wss://' and port)
 
#Enter Host (copied from flespi connection settings without 'wss://' and port)
 
#Enter Username (Copied from flespi Connection settings generated token)
 
#Enter Username (Copied from flespi Connection settings generated token)
Line 64: Line 69:
  
 
===Message format for MQTT publisher===
 
===Message format for MQTT publisher===
 +
----
 
Format is in text - heavier and slower, but less difficult to edit.
 
Format is in text - heavier and slower, but less difficult to edit.
 
{| class="wikitable"
 
{| class="wikitable"
Line 70: Line 76:
 
|-
 
|-
 
|2. Cookie
 
|2. Cookie
|from '''0''' to '''2<sup>64</sup> -1'''
+
| from '''0''' to '''2<sup>64</sup> -1'''
 
|-
 
|-
 
|3. IP Type
 
|3. IP Type
 
|'''0''' - IPv4; '''1''' - IPv6; '''2''' - hostname
 
|'''0''' - IPv4; '''1''' - IPv6; '''2''' - hostname
 
|-
 
|-
|4. IP
+
| 4. IP
 
|IPv6 must be in full format (for example: '''2001:0db8:0000:0000:0000:8a2e:0370:7334''')
 
|IPv6 must be in full format (for example: '''2001:0db8:0000:0000:0000:8a2e:0370:7334''')
 
|-
 
|-
|5. Port
+
| 5. Port
 
|Port number (for example: '''502''')
 
|Port number (for example: '''502''')
 
|-
 
|-
| 6. Timeout in seconds (time to wait for response)
+
|6. Timeout in seconds (time to wait for response)
 
|from '''1''' to '''999'''
 
|from '''1''' to '''999'''
 
|-
 
|-
Line 102: Line 108:
  
 
====Examples====
 
====Examples====
 +
----
 
{| class="wikitable"
 
{| class="wikitable"
| Setting relay (on) (Relay address is 202, which means 'Number of first register will be 203)
+
|Setting relay (on) (Relay address is 202, which means 'Number of first register will be 203)
 
|'''0 65432 0 192.168.1.1 502 5 1 6 203 1'''
 
|'''0 65432 0 192.168.1.1 502 5 1 6 203 1'''
 
|-
 
|-
Line 110: Line 117:
 
|}
 
|}
  
===Testing MQTT Publisher and Subscriber on flespi.io===
+
=== Testing MQTT Publisher and Subscriber on flespi.io ===
 +
----
 
Login and navigate to MQTT Board on https://flespi.io
 
Login and navigate to MQTT Board on https://flespi.io
  
 
Add a subscriber:
 
Add a subscriber:
  
#Press '''''<nowiki/>'+'''''' button on the top right corner
+
# Press '''''<nowiki/>'+'''''' button on the top right corner
#Select '''''<nowiki/>'Subscriber''''''
+
# Select '''''<nowiki/>'Subscriber''''''
 
#In the topic field enter '''''<nowiki/>'response''''''
 
#In the topic field enter '''''<nowiki/>'response''''''
 
#Press '''''<nowiki/>'Subscribe'''''' button
 
#Press '''''<nowiki/>'Subscribe'''''' button
Line 124: Line 132:
 
Add a Publisher:
 
Add a Publisher:
  
#Press '''''<nowiki/>'+'''''' button on the top right corner
+
# Press '''''<nowiki/>'+'''''' button on the top right corner
 
#Select '''''<nowiki/>'Publisher''''''
 
#Select '''''<nowiki/>'Publisher''''''
 
#In the topic field enter '''''<nowiki/>'request''''''
 
#In the topic field enter '''''<nowiki/>'request''''''
Line 139: Line 147:
 
''This Means that MQTT Gateway on Modbus TCP Master router is working correctly and Modbus TCP Slave receives requests.''
 
''This Means that MQTT Gateway on Modbus TCP Master router is working correctly and Modbus TCP Slave receives requests.''
  
==Using RUT240 router as broker==
+
==Using RUT240 router as broker ==
  
 
[[File:Networking Topology MQTT MODBUS RUTbroker configuration v1.png|987x987px]]
 
[[File:Networking Topology MQTT MODBUS RUTbroker configuration v1.png|987x987px]]
  
=== Configuring Modbus TCP Master, MQTT Gateway MQTT Broker on RUT240 and MQTT Publisher/Subscriber on PC ===
+
===Configuring Modbus TCP Master, MQTT Gateway MQTT Broker on RUT240 and MQTT Publisher/Subscriber on PC===
 +
----
 
''Same configuration will be used for Modbus TCP Master and Slave RUT955 routers as in previous example, only settings in Modbus TCP Master router RUT955 will be changed to match MQTT Broker on RUT240 router''
 
''Same configuration will be used for Modbus TCP Master and Slave RUT955 routers as in previous example, only settings in Modbus TCP Master router RUT955 will be changed to match MQTT Broker on RUT240 router''
  
 
Navigate to '''Services > Modbus > MQTT Gateway'''
 
Navigate to '''Services > Modbus > MQTT Gateway'''
  
# '''Enable'''  
+
#'''Enable'''
# Host: '''Enter Public IP address of MQTT Broker (RUT240)'''
+
#Host: '''Enter Public IP address of MQTT Broker (RUT240)'''
 
# Username: '''N/A'''
 
# Username: '''N/A'''
# Password: '''N/A'''
+
#Password: '''N/A'''
# Press '''Save & Apply'''
+
#Press '''Save & Apply'''
  
 
[[File:Networking MQTT Modbus MQTT gateway config v1.png|border|1130x1130px]]
 
[[File:Networking MQTT Modbus MQTT gateway config v1.png|border|1130x1130px]]
  
=== Configuring RUT240 MQTT Broker ===
+
===Configuring RUT240 MQTT Broker ===
 
+
----
  
 
Navigate to '''Services > MQTT > Broker'''
 
Navigate to '''Services > MQTT > Broker'''
  
# Select '''Enable'''
+
#Select '''Enable'''
# Check '''Enable Remote Access'''
+
#Check '''Enable Remote Access'''
# Press '''Save & Apply'''
+
#Press '''Save & Apply'''
  
 
[[File:Networking MQTT Modbus MQTT Broker RUTos config v1.png|border|1133x1133px]]
 
[[File:Networking MQTT Modbus MQTT Broker RUTos config v1.png|border|1133x1133px]]
  
=== Testing MQTT Gateway ===
+
===Testing MQTT Gateway===
 
+
----
  
 
For testing purposes, two terminal windows will be used on the same PC.  
 
For testing purposes, two terminal windows will be used on the same PC.  
Line 174: Line 183:
 
''To get Ubuntu terminal  on Windows 10/11, refer to the following link for instructions:'' https://tutorials.ubuntu.com/tutorial/tutorial-ubuntu-on-windows#0
 
''To get Ubuntu terminal  on Windows 10/11, refer to the following link for instructions:'' https://tutorials.ubuntu.com/tutorial/tutorial-ubuntu-on-windows#0
  
* Open first terminal, which will act as '''Subscriber'''. Type in:  
+
*Open first terminal, which will act as '''Subscriber'''. Type in:
  
 
<blockquote>''mosquito_sub -h [Host_address] -p [Port] -t [Topic]''</blockquote>[[File:Networking MQTT Modbus Subscriber in terminal v1.png]]
 
<blockquote>''mosquito_sub -h [Host_address] -p [Port] -t [Topic]''</blockquote>[[File:Networking MQTT Modbus Subscriber in terminal v1.png]]
Line 182: Line 191:
 
<blockquote>''mosquito_pub -h [Host] -h [Host_address] -p [Port] -m [‘Message’] -t [Topic]''</blockquote>[[File:Networking MQTT Modbus Publisher testing v1.png]]
 
<blockquote>''mosquito_pub -h [Host] -h [Host_address] -p [Port] -m [‘Message’] -t [Topic]''</blockquote>[[File:Networking MQTT Modbus Publisher testing v1.png]]
  
* On the first window - '''Subscriber''', a response should appear
+
*On the first window - '''Subscriber''', a response should appear
  
 
[[File:Networking MQTT Modbus Subscriber response ubuntu v1.png]]
 
[[File:Networking MQTT Modbus Subscriber response ubuntu v1.png]]

Revision as of 14:42, 12 July 2022

Summary

In this guide Modbus TCP master MQTT Gateway function will be configured with two different types of MQTT Brokers. First using third party MQTT Broker services (in this example Flespi.io). Second using RUT240 router as MQTT Broker. Two RUT955 routers will be used as Modbus TCP Master and Slave, and PC acts as MQTT Publisher and Subscriber.

Using flespi.io as Broker

Networking Topology MQTT MODBUS flespi configuration v1.png

Configuring RUT955 Modbus TCP Slave


Go to Services > Modbus > Modbus TCP Slave:

  1. Check Enable
  2. Enter port that will be used, in this example 502 will be used
  3. Enter device ID
  4. Press Save & Apply

Networking MQTT MODBUS flespi configuration slave1 v1.png

*In this config LAN port is used so “Allow Remote Access” is not needed

Modbus TCP Slave RUT955 is now configured.

Configuring RUT955 Modbus TCP Master


Go to Services > Modbus > Modbus TCP Master

  1. Press Add
  2. Check Enable
  3. Enter name for slave device
  4. Slave ID must match with previously configured Slave device ID
  5. Enter IP address of Modbus TCP Slave device
  6. Chose same Port as in Slave device - 502
  7. Enter Period in seconds, how often requests will be sent to Slave device
  8. Enter new request name and press Add in Requests configurations
  9. Choose Data type and Function, enter First register/coil/input to be read or written and Register count. You can name each individual configuration, and then select enable on configurations that you want to use. In this example, register to get WAN IP address of the slave device is used.
  10. Press Test button in Request Configuration Testing to see if Slave device respond to requests, response similar to image below should be shown.
  11. Press Save & Apply

Configuring Flespi.io MQTT Broker


Login or create an account on https://flespi.io

Networking MQTT Modbus flespiio login.png

Once logged in:

  1. Navigate to MQTT Board on the left side of the screen and press it. Networking MQTT Modbus flespi board.png
  2. On the right hand panel, top right corner, next to the name of the MQTT board, press the cogwheel looking icon to open Connection Settings
  3. In the opened window, press "Get flespi token" to generate an username
  4. Enter Client name
  5. Copy Host address
  6. Copy Username
  7. Create a password
  8. Press Save

Networking MQTT modbus fespi Connection settings v1.png

Configuring MQTT Gateway on RUT955 Modbus TCP Master


Open routers WebUI and navigate to Services > Modbus > MQTT Gateway

  1. Select Enable
  2. Enter Host (copied from flespi connection settings without 'wss://' and port)
  3. Enter Username (Copied from flespi Connection settings generated token)
  4. Enter Password

Networking MQTT Modbus Rut configuration Mqtt gateway v1.png

You can change Request and Response topics that you will have to publish and subscribe to get information from Modbus TCP Master through MQTT Gateway, but for this example they are left on default topics

Message format for MQTT publisher


Format is in text - heavier and slower, but less difficult to edit.

1. Format version 0
2. Cookie from 0 to 264 -1
3. IP Type 0 - IPv4; 1 - IPv6; 2 - hostname
4. IP IPv6 must be in full format (for example: 2001:0db8:0000:0000:0000:8a2e:0370:7334)
5. Port Port number (for example: 502)
6. Timeout in seconds (time to wait for response) from 1 to 999
7. Slave ID - Indicates to which slave request is sent from 1 to 255
8. Function 3 - read registers; 6 - write single register; 16 - write multiple registers
9. Number of first register from which information will be read or written from 1 to 65535
10. Registry value If function is 3 - from 1 to 123 (first register + registry value can not go out of range);

If function is 6 - from 0 to 65535

If function is 16 - from 1 to 123 (first register + registry value can not go out of range), Registry values separated by commas without spaces. Example.: 1,2,3,654,21,789. There has to be as many values, as specified number of registers, and each value must be between 0 and 65535. If number of registries is 0, there should be no registry values

Networking MQTT modbus message format publisher v1.png

Examples


Setting relay (on) (Relay address is 202, which means 'Number of first register will be 203) 0 65432 0 192.168.1.1 502 5 1 6 203 1
Getting uptime 0 65432 0 192.168.1.1 502 5 1 3 2 2

Testing MQTT Publisher and Subscriber on flespi.io


Login and navigate to MQTT Board on https://flespi.io

Add a subscriber:

  1. Press '+' button on the top right corner
  2. Select 'Subscriber'
  3. In the topic field enter 'response'
  4. Press 'Subscribe' button

Networking MQTT Modbus flespi subscriber config1 v1.png Networking MQTT Modbus flespi subscriber config2 v1.png

Add a Publisher:

  1. Press '+' button on the top right corner
  2. Select 'Publisher'
  3. In the topic field enter 'request'
  4. In the message field enter message, for this example 'Getting uptime' is used
  5. Press 'Publish' button

Networking MQTT Modbus flespi publisher config1 v1.png Networking MQTT Modbus flespi publisher config2 v1.png


Check the response in the 'Subscriber' tab, you should receive a message similar to the one below.

Networking MQTT Modbus flespi Response v1.png

This Means that MQTT Gateway on Modbus TCP Master router is working correctly and Modbus TCP Slave receives requests.

Using RUT240 router as broker

Networking Topology MQTT MODBUS RUTbroker configuration v1.png

Configuring Modbus TCP Master, MQTT Gateway MQTT Broker on RUT240 and MQTT Publisher/Subscriber on PC


Same configuration will be used for Modbus TCP Master and Slave RUT955 routers as in previous example, only settings in Modbus TCP Master router RUT955 will be changed to match MQTT Broker on RUT240 router

Navigate to Services > Modbus > MQTT Gateway

  1. Enable
  2. Host: Enter Public IP address of MQTT Broker (RUT240)
  3. Username: N/A
  4. Password: N/A
  5. Press Save & Apply

Networking MQTT Modbus MQTT gateway config v1.png

Configuring RUT240 MQTT Broker


Navigate to Services > MQTT > Broker

  1. Select Enable
  2. Check Enable Remote Access
  3. Press Save & Apply

Networking MQTT Modbus MQTT Broker RUTos config v1.png

Testing MQTT Gateway


For testing purposes, two terminal windows will be used on the same PC.

To get Ubuntu terminal on Windows 10/11, refer to the following link for instructions: https://tutorials.ubuntu.com/tutorial/tutorial-ubuntu-on-windows#0

  • Open first terminal, which will act as Subscriber. Type in:

mosquito_sub -h [Host_address] -p [Port] -t [Topic]

Networking MQTT Modbus Subscriber in terminal v1.png

  • Open second terminal, which will act as Publisher. Type in:

mosquito_pub -h [Host] -h [Host_address] -p [Port] -m [‘Message’] -t [Topic]

Networking MQTT Modbus Publisher testing v1.png

  • On the first window - Subscriber, a response should appear

Networking MQTT Modbus Subscriber response ubuntu v1.png