RMS - Commands menu

From Teltonika Networks Wiki
Revision as of 16:30, 27 June 2019 by RytisB (talk | contribs)

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)

Summary[edit | edit source]


The RMS features described in this have changed since the last update. The content on this page will be updated ASAP.


RMS Changes.jpg


The Commands submenu located in the Management menu tab can be used to update firmware, set LAN and Mobile configurations, set up remote access to devices connected to your router's LAN and reboot devices registered on your RMS profile. This section of the RMS user manual provides an overview on the functions of the Commands submenu.

Update firmware[edit | edit source]

To Update firmware firmware for device(s) selected from your device table go to the RMS web page, Left sidebar panel, (Management → Devices) and click on Devices submenu.

Move your mouse pointer to the Top control Actions menu and select Update firmware (Actions → Update firmware).

RMS-device-menu-left-sidebar-panel.jpg RMS-top-menu-actions-update-firmware.jpg


Step by step instructions[edit source]


Read step by step instructions to learn how to update firmware for your device(s).

  1. Select the device(s) that you wish to update
  2. Move your mouse pointer to the Actions menu and click "Update firmware".
  3. After a pop-up window will appear. Select the Latest firmware or Mass product from the top of the list. You also can select the firmware you have previously uploaded.
  4. Click the Set update button, you will get a pop-up window showing firmware upload progress.
  5. After the firmware upload has complete in the Status column you will you will get a message: Done.
  6. You can safely close the pop-up window by clicking Close button.

Important!

  • Allow some time for your device(s) to update. They wont be reachable for up to 1-2 minute(s).
  • When the red circle (Offline) will change to green circle (Online) the device(s) have been updated and now are fully operational.

Your device(s) will be unreachable for a few minutes and will thus be shown as "Offline". The power button symbols located next to each device in the device table indicate the monitoring status of these devices. When it turns green, the firmware updates will have finished and the device(s) will be seen as "Online" in RMS.

Download firmware manually[edit source]


Firmware files can be uploaded to RMS via the RMS Files page or they can uploaded from your computer. You can download firmware for different devices from these links:



Configuration[edit | edit source]

The Configure device option allows you to modify configuration for your selected device(s). To configure your devices go to the RMS web page, Left sidebar panel, (Management → Devices) and click on Devices submenu.

Scroll your mouse pointer to the Top control Configuration menu and select Configure device (Configuration → Configure device).

RMS-device-menu-left-sidebar-panel.jpg RMS-top-menu-configuration-mobile.jpg

The Configuration function is used to change configuration of devices selected from your device table. You will get different configuration options depending on the device.

Step by step instructions[edit source]


  1. Select the device(s) that you wish to configure.
  2. Move your mouse pointer to the Configuration menu and click Configure device.
  3. You will get a pop-up box, where you will be able to choose settings you want to configure.
  4. Fill out the information and click Save button when ready.
  5. In the next window will display configuration progress.
  6. Click the Close button and close the Configure devices window.

Important!

  • Allow some time for your device(s) to load new settings. It might take some time.


Access[edit | edit source]

To configure device access go to the RMS web page, Left sidebar panel, (Management → Devices) and click on Devices submenu.

Move your mouse pointer to the Top control Actions menu and select Device Access (Actions → Device Access).

RMS-device-menu-left-sidebar-panel.jpg RMS-top-menu-actions-access.jpg


Configure device access[edit source]


  1. Make sure that the device for which you would like to set up remote access is physically connected to the router's LAN or WAN (depends on your configuration).
  2. Locate and select that device in the device table.
  3. Move your mouse pointer to the Actions menu and click Device Access.
  4. New pop-up window will open, click the plus sign Rms plus symbol.png to create a new row.
  5. Fill out the new row will appropriate data (look for example in the table below). When ready, click "Save".
  6. Enter a custom name for the device (for easier management purposes), the device's destination IP address, and the device's destination port.

The next Actions status pop-up will display the status of your request. If update is successful in the Status column you will you will get a message: LAN device(s) created successfully.


Field Value Description
Name For example: RUT955 A custom name for the LAN device.
Destination IP For example: 192.168.1.2 The device’s LAN IP address.
Destination Port Default: 80 The destination device's WebUI HTTP port.


Connect to device[edit source]


RMS-device-details-button.png

  1. You can then find remote access links in the Device details page. You can find this page by clicking the "Device Information" icon located under the Actions column in the Device table, next to the relevant device.
  2. You will be redirected to the device's Device details page. By default, the Device access widget will be at the bottom of that page. Locate the custom name for the device you created in previous steps.
  3. A Device Web UI link pop-up window will open. Click the Generate button.
  4. A new link will appear in the window. Click the link to connect to the device.
  5. For this example, I used another Teltonika Networks device that was connected to the RMS device's LAN. Therefore, when I click the link, I am redirected to WebUI login page.

Remove from device access list[edit source]


RMS-remove-device-access.png

  1. You can later delete device access entries by once again selecting the device and clicking "Access" from the Actions menu.
  2. When the new pop-window opens click the Remove access listing icon next to the entry that you would like to delete.

RMS-access-deleted.png

At the top of your screen, you will get a notification in green text: Device access deleted.

Reboot[edit | edit source]

Reboot[edit source]

To Reboot device(s) selected from your device table go to the RMS web page, Left sidebar panel, (Management → Devices) and click on Devices submenu.

Move your mouse pointer to the Top control Actions menu and select Reboot (Actions → Reboot).

RMS-device-menu-left-sidebar-panel.jpg RMS-top-menu-actions-reboot.jpg

The Reboot function is used to reboot devices selected from your device table.


Instructions[edit source]


  1. Select the device(s) that you wish to reboot.
  2. Move your mouse pointer to the Actions menu and click Reboot.
  3. You will get a pop-up asking whether you really want to reboot the selected device(s). If you're ready to proceed, click Yes.
  4. The next pop-up box will display the status of each device.

If the reboot is successful in the Status column you will you will get a message: Successfully Rebooted device.

Important!

  • Your device(s) will be unreachable for a few minutes and shown as (Offline) in RMS.
  • When the red circle (Offline) will change to green circle (Online) the device(s) have been rebooted and now are fully operational.