Difference between revisions of "RUT850 Routing"

From Teltonika Networks Wiki
 
(One intermediate revision by the same user not shown)
Line 19: Line 19:
 
     <tr>
 
     <tr>
 
       <td>Routing table</td>
 
       <td>Routing table</td>
       <td>Main {{!}} WAN {{!}} WAN2 {{!}} WAN3; Default: '''WAN'''</td>
+
       <td>Main | WAN | WAN2 | WAN3; Default: '''WAN'''</td>
 
       <td>Defines which table will be used for the route in question</td>
 
       <td>Defines which table will be used for the route in question</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
       <td>Interface</td>
 
       <td>Interface</td>
       <td>LAN {{!}} WAN(wired) {{!}} WAN2(Mobile) {{!}} WAN3(WiFi) {{!}} VPN instances; Default: '''WAN(wired)'''</td>
+
       <td>LAN | WAN(wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; Default: '''WAN(wired)'''</td>
 
       <td>The zone where the target network resides</td>
 
       <td>The zone where the target network resides</td>
 
     </tr>
 
     </tr>
Line 84: Line 84:
 
     </tr>
 
     </tr>
 
</table>
 
</table>
 +
 +
[[Category:RUT850 Network section]]

Latest revision as of 10:48, 7 May 2020

Main Page > RUT Routers > RUT850 > RUT850 Manual > RUT850 WebUI > RUT850 Network section > RUT850 Routing

Summary

This chapter is an overview of the Routing section in RUT devices.

Static Routes

Static routes specify over which interface and gateway a certain host or network can be reached. In this page you can configure your own custom routes.


Network routing static routes.PNG

field name value description
Routing table Main | WAN | WAN2 | WAN3; Default: WAN Defines which table will be used for the route in question
Interface LAN | WAN(wired) | WAN2(Mobile) | WAN3(WiFi) | VPN instances; Default: WAN(wired) The zone where the target network resides
Destination address* ip; Default: 0.0.0.0 The address of the destination network
Netmask* ip; Default: 0.0.0.0 A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies
Gateway ip; Default: " " Defines where the router should send all the traffic that applies to the rule
Metric integer; Default: 0 The Metric value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the higher metric is applied

*Additional notes on Destination & Netmask:

You can define a rule that applies to a single IP like this: Destination - some IP; Netmask - 255.255.255.255. Furthermore, you can define a rule that applies to a segment of IPs like this: Destination – some IP that STARTS some segment; Netmask – Netmask that defines how large the segment is. e.g.:

field name value description
192.168.55.161 255.255.255.255 Only applies to 192.168.55.161
192.168.55.0 255.255.255.240 Applies to IPs in the 192.168.55.0 - 192.168.55.255
192.168.55.240 255.255.255.240 192.168.55.240 - 192.168.55.255
192.168.55.161 255.255.255.0 192.168.55.0 - 192.168.55.255
192.168.0.0 255.255.0.0 192.168.0.0 - 192.168.255.255