Difference between revisions of "RUT950 Administration"

From Teltonika Networks Wiki
Line 27: Line 27:
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
     <td>New password {{!}} Confirm new password</td>
+
     <td>New password | Confirm new password</td>
 
         <td>string; Default: '''admin01'''</td>
 
         <td>string; Default: '''admin01'''</td>
 
         <td>Changes the router's admin password </td>
 
         <td>Changes the router's admin password </td>
Line 33: Line 33:
 
     <tr>
 
     <tr>
 
     <td>Language</td>
 
     <td>Language</td>
         <td>English {{!}} Deutsch {{!}} Français {{!}} Turkish; Default: '''English'''</td>
+
         <td>English | Deutsch | Français | Turkish; Default: '''English'''</td>
 
         <td>Selects the router's interface language</td>
 
         <td>Selects the router's interface language</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
       <td>IPv6 Support</td>
 
       <td>IPv6 Support</td>
       <td>yes {{!}} no; Default: '''no'''</td>
+
       <td>yes | no; Default: '''no'''</td>
 
       <td>Toggles IPv6 suport ON or OFF</td>
 
       <td>Toggles IPv6 suport ON or OFF</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
       <td>Show mobile info at login page</td>
 
       <td>Show mobile info at login page</td>
       <td>yes {{!}} no; Default: '''no'''</td>
+
       <td>yes | no; Default: '''no'''</td>
 
       <td>Show mobile data connection information (signal strength, state, service mode) at login page</td>
 
       <td>Show mobile data connection information (signal strength, state, service mode) at login page</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Show WAN IP at login page</td>
 
     <td>Show WAN IP at login page</td>
         <td>yes {{!}} no; Default: '''no'''</td>
+
         <td>yes | no; Default: '''no'''</td>
 
         <td>Show the router's WAN IP address at login page</td>
 
         <td>Show the router's WAN IP address at login page</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>LEDs Indication</td>
 
     <td>LEDs Indication</td>
         <td>yes {{!}} no; Default: '''yes'''</td>
+
         <td>yes | no; Default: '''yes'''</td>
 
         <td>Toggles LED indication ON or OFF</td>
 
         <td>Toggles LED indication ON or OFF</td>
 
     </tr>
 
     </tr>
Line 81: Line 81:
 
     <tr>
 
     <tr>
 
       <td>System log level</td>
 
       <td>System log level</td>
       <td>Debug {{!}} Info {{!}} Notice {{!}} Warning {{!}} Error {{!}} Critical {{!}} Alert {{!}} Emergency; Default: '''Debug''' </td>
+
       <td>Debug | Info | Notice | Warning | Error | Critical | Alert | Emergency; Default: '''Debug''' </td>
 
       <td>You can watch logs by choosing a group from the dropdown list and clicking  '''Show''' button</td>
 
       <td>You can watch logs by choosing a group from the dropdown list and clicking  '''Show''' button</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
       <td>Save log in</td>
 
       <td>Save log in</td>
       <td>RAM memory {{!}} Flash memory; Default: '''RAM memory'''</td>
+
       <td>RAM memory | Flash memory; Default: '''RAM memory'''</td>
 
       <td>Specifies where to save log information. The router needs to be rebooted in order for this effect to take place</td>
 
       <td>Specifies where to save log information. The router needs to be rebooted in order for this effect to take place</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Include GSMD information</td>
 
     <td>Include GSMD information</td>
         <td>yes {{!}} no; Default: '''yes'''</td>
+
         <td>yes | no; Default: '''yes'''</td>
 
         <td>Inlcludes GSMD information in the router's logs</td>
 
         <td>Inlcludes GSMD information in the router's logs</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Include PPPD information</td>
 
     <td>Include PPPD information</td>
         <td>yes {{!}} no; Default: '''no'''</td>
+
         <td>yes | no; Default: '''no'''</td>
 
         <td>Inlcludes PPPD information in the router's logs</td>
 
         <td>Inlcludes PPPD information in the router's logs</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Include Chat script information</td>
 
     <td>Include Chat script information</td>
         <td>yes {{!}} no; Default: '''yes'''</td>
+
         <td>yes | no; Default: '''yes'''</td>
 
         <td>Inlcludes Chat script information in the router's logs</td>
 
         <td>Inlcludes Chat script information in the router's logs</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
     <td>Include network topology information</td>
 
     <td>Include network topology information</td>
         <td>yes {{!}} no; Default: '''no'''</td>
+
         <td>yes | no; Default: '''no'''</td>
 
         <td>Inlcludes network topology information in the router's logs</td>
 
         <td>Inlcludes network topology information in the router's logs</td>
 
     </tr>
 
     </tr>
Line 143: Line 143:
 
     <tr>
 
     <tr>
 
       <td>Enable</td>
 
       <td>Enable</td>
       <td>yes {{!}} no; Default: '''yes'''</td>
+
       <td>yes | no; Default: '''yes'''</td>
 
       <td>Toggles secure SSH/WebUI access ON or OFF. If this is checked, devices logging in have a limited amount of tries specified in the '''Fail count''' field to log in to the router</td>
 
       <td>Toggles secure SSH/WebUI access ON or OFF. If this is checked, devices logging in have a limited amount of tries specified in the '''Fail count''' field to log in to the router</td>
 
     </tr>
 
     </tr>
 
     <tr>
 
     <tr>
 
       <td>Clean after reboot</td>
 
       <td>Clean after reboot</td>
       <td>yes {{!}} no; Default: '''no'''</td>
+
       <td>yes | no; Default: '''no'''</td>
 
       <td>If this field is checked, blocked addresses are removed after every reboot</td>
 
       <td>If this field is checked, blocked addresses are removed after every reboot</td>
 
     </tr>
 
     </tr>
Line 179: Line 179:
 
==Root CA==
 
==Root CA==
 
{{Template:rut manual system administration root ca}}
 
{{Template:rut manual system administration root ca}}
 +
 +
[[Category:RUT950 WebUI]]

Revision as of 08:56, 1 March 2019

Main Page > RUT Routers > RUT950 > RUT950 Manual > RUT950 WebUI > RUT950 System section > RUT950 Administration

Summary

This chapter is an overview of RUT routers' System->Administration section

General

The General section is used to change some of the most general configurations of the router (password, language, etc.)


System administration general rut950.png

field name value description
Router name string; Default: RUT950 Router's name, used for easier management purposes
Host name string; Default: Teltonika-RUT950.com Router's host name, i.e., an address from which you can reach the router's WebUI
New password | Confirm new password string; Default: admin01 Changes the router's admin password
Language English | Deutsch | Français | Turkish; Default: English Selects the router's interface language
IPv6 Support yes | no; Default: no Toggles IPv6 suport ON or OFF
Show mobile info at login page yes | no; Default: no Show mobile data connection information (signal strength, state, service mode) at login page
Show WAN IP at login page yes | no; Default: no Show the router's WAN IP address at login page
LEDs Indication yes | no; Default: yes Toggles LED indication ON or OFF
Reset button configuration integer [5..60]; Default: 5 Specifies the minimum amount of time (in seconds) that the reset button has to be pressed and held in order to initiate a factory reset
Restore to default - Restores the router to it's default state (factory settings)

Troubleshoot

System administration troubleshoot.PNG

field name value description
System log level Debug | Info | Notice | Warning | Error | Critical | Alert | Emergency; Default: Debug You can watch logs by choosing a group from the dropdown list and clicking Show button
Save log in RAM memory | Flash memory; Default: RAM memory Specifies where to save log information. The router needs to be rebooted in order for this effect to take place
Include GSMD information yes | no; Default: yes Inlcludes GSMD information in the router's logs
Include PPPD information yes | no; Default: no Inlcludes PPPD information in the router's logs
Include Chat script information yes | no; Default: yes Inlcludes Chat script information in the router's logs
Include network topology information yes | no; Default: no Inlcludes network topology information in the router's logs

System log - Provides on-screen System logging information. It does not, however, substitute troubleshooting file.

Kernel log - Provides on-screen Kernel logging information. It does not, however, substitute the troubleshooting file.

Troubleshoot file - Downloadable archive, that contains full router configuration and all System log files.

In addition, you can also download the router's troubleshoot file at any time and the TCP dump file if the Enable TCP dump field is checked.

Backup

Template:Rut manual system administration backup

Access Control

General


The Access Control General window is used the Enable or Disable SSH, HTTP or HTTPS remote or local access to the RUT device.


System administration access control.PNG

Safety


System administration access control safety.PNG

field name value description
Enable yes | no; Default: yes Toggles secure SSH/WebUI access ON or OFF. If this is checked, devices logging in have a limited amount of tries specified in the Fail count field to log in to the router
Clean after reboot yes | no; Default: no If this field is checked, blocked addresses are removed after every reboot
Fail count integer; Default: 5 Maximal login fail count after which the devices's address is blocked and appears in the List Of Blocked Addresses section

Diagnostics

The Diagnostics page is used to diagnose whether you have an internet connection, trace routes of specified addresses and to perform NSlookups by sending ICMP ping packets to a specified host or IP address.


System administration diagnostics.PNG

MAC Clone

System administration mac clone.PNG

Overview

The Administration->Overview section is used to configure which widgets should be shown in the Overview page.

System administration overview.PNG

RMS

Template:Rut manual system administration rms

Root CA

Template:Rut manual system administration root ca