Open main menu

RUTX11 Mobile

This is the approved revision of this page, as well as being the most recent.
Main Page > RUTX Routers > RUTX11 > RUTX11 Manual > RUTX11 WebUI > RUTX11 Network section > RUTX11 Mobile

The information in this page is updated in accordance with firmware version RUTX_R_00.02.03.1

Contents

Summary

The Mobile page is used for setting parameters related to the mobile data connection. This page is an overview of the Mobile section for RUTX11 devices.

This manual page provides an overview of the Users windows in RUTX11 devices.

If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.

 

General

The General section is used to configure the SIM card parameters that define how the device establishes connection and uses other, mobile related, useful features.

SIM card settings


The SIM card settings section is used to configure main SIM card parameters. Refer to the figure and table below for information on the fields contained in that section.  


field name value description
Default SIM off | on; Default:on Set this SIM slot as default
Deny data roaming off | on; Default: off Deny data connection on roaming
Service mode Default: Auto Your network's preference. If your local mobile network supports UMTS (3G) or LTE (4G) you can specify to which network you prefer to connect to. Available options:
  • Auto
  • 4G (LTE) only
  • 3G only
PIN Default: " " SIM card's PIN (Personal Identification Number) is a secret numeric password shared between a user and a system that can be used to authenticate the user

SMS limit settings


The SMS limit settings section provides you with the possibility to set SMS limit for your SIM card.

 

field name value description
Enable SMS Limit off | on; default: off Enable of disable SMS limit feature
SMS limit count Default: Disable SMS sending after limit value is reached
Period Default: Day Period for which SMS limiting should apply. Available options:
  • Day
  • Week
  • Month

This section also contains one button - Clear SMS limit. When clicked, the button resets the sms limit counter for the related SIM card. Thus, the count is started over again regardless of the specified period.

SIM switch


In SIM switch section you can configure SIM switching rules, i.e., set up circumstances under which the device will perform a switch from using one SIM card to the other. Refer to the figure and table below for information.

 

field name value description
Enable automatic switching off | on; default: off Automatically switch between primary and secondary SIM cards based on the various rules and criterias
Check interval integer; default: 10 The frequency at which the router will check for condition changes corresponding to SIM switch rules. If such a condition exists, the router will perform a SIM switch, if not - it will check for the same conditions again after the amount of time specified in this field.
Attempts before SIM switching integer; default: 3 Amount of the check attempts for condition changes corresponding to SIM switch rules.
On weak signal off | on; default: off Perform a SIM card switch when a signal's strength drops below a certain threshold
On data limit off | on; default: off Perform a SIM card switch when mobile data limit for your current SIM card is exceeded
On SMS limit off | on; default: off Perform a SIM card switch when sent SMS limit for your current SIM card is exceeded
On roaming off | on; default: off Perform a SIM card switch when roaming is detected
No network off | on; default: off Perform a SIM card switch when network isn't detected
On network denied off | on; default: off Perform a SIM card switch when network is denied
On data connection fail off | on; default: off Perform a SIM card switch when data connection fails

Network operators

The Network operators tab provides you with the possibility to scan for and manually manage mobile network operators to which the device's SIM card can connect to. Operator selection is only available for the primary SIM card. In order to specify an operator for the other SIM card it must first be selected as the primary SIM in the SIM Management section.

 

Operators scan settings


As default Connection mode is set to AUTO, although to initiate a scan, select connection mode Manual, press Scan for operators and then you will be prompted with a pop-up asking if you wish to proceed. This is because while the scan is in progress you will lose your data connection for up to 3 minutes.

 

In order to configure a specific band, simply select which one you want to use and press Save & Apply