Difference between revisions of "Setting up WAN as LAN"

From Teltonika Networks Wiki
 
(12 intermediate revisions by 7 users not shown)
Line 1: Line 1:
 +
<p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.6'''] firmware version .</p>
 +
 
==Introduction==
 
==Introduction==
This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RutX devices.
+
This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RUTOS devices.
 +
 
 +
 
 +
==Alternative 1==
 +
 
 +
Set your WebUI to '''Basic Mode''':
 +
[[File:Networking device configuration example webui basic mode v1.png|border|center|class=tlt-border|1000x100px]]
 +
 
 +
Navigate to '''Network → LAN → edit LAN''' the instance:
 +
[[File:Networking device configuration example lan edit interface v1.png|border|center|class=tlt-border|1000x100px]]
 +
 
 +
Once there, '''enable the Use WAN port as LAN''':
 +
[[File:Networking device configuration example lan enable wan v1.png|border|center|class=tlt-border|1000x265px]]
 +
 
 +
==Alternative 2==
 +
 
 +
Enable the '''ADVANCED mode''' on the WebUI . This will allow you to choose from a larger variety of settings:
 +
[[File:Networking device configuration example webui advance mode v1.png|border|center|class=tlt-border|1000x100px]]
 +
 
 +
Navigate to '''Network →  Interfaces →  General''' and '''disable WAN and WAN6''' interfaces:
 +
[[File:Networking device configuration example wan disable wan v1.png|border|center|class=tlt-border|1000x173px]]
 +
 
 +
Click on '''edit the WAN''' interface and once a new window pops-up '''go to''' '''Physical settings'''. There, under the '''Interface''' '''add -- No interface --''':
 +
[[File:Networking device configuration example wan wan interface v1.png|border|center|class=tlt-border|1000x465px]]
 +
 
 +
Click on '''edit the WAN6''' interface and once a new window pops-up '''go to''' '''Physical settings'''. There, under the '''Interface''' '''add -- No interface --''':
 +
[[File:Networking device configuration example wan wan6 interface v1.png|border|center|class=tlt-border|1000x465px]]
  
===Configuring WAN as LAN===
+
Click on '''edit the LAN''' interface and once a new window pops-up '''go to''' '''Physical settings'''. There, under the '''Interface''' '''add eth1''':
* First you want to make sure that you have '''ADVANCED mode''' enabled. This will allow you to choose from a larger variety of settings.
+
[[File:Networking device configuration example lan lan interface v1.png|border|center|class=tlt-border|1000x465px]]
[[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]]
 
----
 
* After that navigate to Network > Interfaces
 
[[File:Network_interface_settings.png|200px|border|class=tlt-border]]
 
  
* Disable WAN interface
+
==Test the configuration==
[[File:Interfaces disable wan.png|border|class=tlt-border|1100px]]
 
----
 
* Next we will '''edit''' our LAN interface and navigate to '''Physical settings''' where we will add Interface item from the dropdown menu.
 
[[File:Physical settings of interface lan.png|border|1100px|class=tlt-border]]
 
----
 
* Select Ethernet Adapter item, by default it's '''eth1'''
 
[[File:Ethernet adapter in lan interface.png|border|class=tlt-border]]
 
----
 
* It should result in something like this.
 
[[File:Eth1 appears in lan interface.png|border|class=tlt-border|1100px]]
 
----
 
* Once you're done with configurations above just '''save any changes you made'''. Now head to VLAN settings and check if WAN VLAN ID 1 is disabled, and ID 2 is untagged.
 
[[File:Vlan settings for wan as lan.png|border|class=tlt-border|1100px]]
 
----
 
 
At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router.
 
At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router.
 +
[[File:Pings useful.png|border|center|class=tlt-border|734x232px]]
 +
[[Category:LAN]]

Latest revision as of 06:17, 24 January 2024

Main Page > General Information > Configuration Examples > LAN > Setting up WAN as LAN

The information on this page is updated in accordance with the 00.07.6 firmware version .

Introduction

This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RUTOS devices.


Alternative 1

Set your WebUI to Basic Mode:

Networking device configuration example webui basic mode v1.png

Navigate to Network → LAN → edit LAN the instance:

Networking device configuration example lan edit interface v1.png

Once there, enable the Use WAN port as LAN:

Networking device configuration example lan enable wan v1.png

Alternative 2

Enable the ADVANCED mode on the WebUI . This will allow you to choose from a larger variety of settings:

Networking device configuration example webui advance mode v1.png

Navigate to Network → Interfaces → General and disable WAN and WAN6 interfaces:

Networking device configuration example wan disable wan v1.png

Click on edit the WAN interface and once a new window pops-up go to Physical settings. There, under the Interface add -- No interface --:

Networking device configuration example wan wan interface v1.png

Click on edit the WAN6 interface and once a new window pops-up go to Physical settings. There, under the Interface add -- No interface --:

Networking device configuration example wan wan6 interface v1.png

Click on edit the LAN interface and once a new window pops-up go to Physical settings. There, under the Interface add eth1:

Networking device configuration example lan lan interface v1.png

Test the configuration

At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router.

Pings useful.png