The information in this page is updated in accordance with firmware version TRB1_R_00.02.06.1.
Summary[edit | edit source]
The Mobile page is used to configure mobile connection settings.
This manual page provides an overview of the Mobile page in TRB142 devices.
If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.
General[edit | edit source]
The General section is used to configure SIM card parameters that define how the device will establish a mobile connection.
Operator settings[edit | edit source]
The Operator Settings section is used to configure which operators can be allowed (Whitelist) or blocked (Blacklist).
|Enable||off | on; default: off||Enables Whitelist or Blacklist for specified operator list.|
|Mode||Whitelist | Blacklist; default: Whitelist||Mode to be applied for operator list.
|Operator list||operator list; default: none||A list of operators which can be configured in Operators List page.|
SIM card settings[edit | edit source]
The SIM Card Settings section is used to configure main SIM card parameters. Refer to the figure and table below for information on the fields contained in that section.
|Deny data roaming||off | on; default: off||Denies data connection on roaming conditions.|
|Service mode||Auto | 4G (LTE) only | 3G only | 2G only; default: Auto||Network connection type preference.|
|PIN||integer [0000..999999999999]; default: none||SIM card's PIN (Personal Identification Number) is a secret numeric password used to authenticate the device to the SIM card. PIN codes are comprised of numbers only and the length can range from 4 to 12 symbols. PIN number is saved in flash memory therefore it does not reset when default settings are restored.|
SMS limit settings[edit | edit source]
The SMS Limit Settings section provides you with the possibility to set up a maximum sent SMS message cap for your SIM card.
|Enable SMS Limit||off | on; default: off||Turns SMS limiting on or off.|
|SMS limit count||integer; default: none||Sets the SMS sending cap, i.e., how many SMS messages can be sent from this SIM card during the specified period.|
|Period||Day | Week | Month; default: Day||Period for which SMS limiting should apply. After the period expires, the SMS limit counter will be reset.|
|Clear SMS Limit||- (interactive button)||Clears the SMS limit counter for the selected period.|
Unstructured Supplementary Service Data (USSD) is communication protocol used in communication between cellular devices and mobile network operators. It is usually used with prepaid SIM cards to enable/disable certain services or to obtain information from a network operator.
This section provides the possibility to send USSD messages to the mobile operator.
|USSD||string; default: none||Enter a USSD code (up to 182 character) that you wish to send. To send the entered USSD code, click the 'Send' button below the Response box.|
|Response message||string; default: No response yet||Displays the response to the last sent USSD message. Receiving the response may take up to a minute.|
|Send||- (interactive button)||Click to send the message entered in the USSD field.|
Network operators[edit | edit source]
The Network operators section provides you with the possibility to scan for and manage mobile network operators to which the device's SIM card can connect to.
|Current operator||string; default: none||Displays the name of the operator the which the device is currently connected.|
|Connection mode||Auto | Manual; default: Auto||Operator selection method.
Manual operator selection[edit | edit source]
To select an operator manually, specify Connection mode: Manual and click 'Scan For Operators'.
Will be prompted with a pop-up asking if you're sure. Click 'Yes' if you wish to proceed.
Wait for the scan to finish. As indicated by the onscreen message, the process can take up to 3 minutes.
Once the scan has finished, you will see the results in the 'Operators List'.
In order to lock the SIM card to using a single operator, place a check mark next to the relevant entry in the list and click 'Save & Apply'.
Operators list[edit | edit source]
This section is used to create lists of operators codes, which can then be used in Operator settings section to Whitelist of Blacklist them. Operator code consists of two parts - Mobile Country Code (MCC) and Mobile Network Code (MNC).