Template:Networking rut955 manual modbus serial

Summary

Modbus is a serial communications protocol originally published by Modicon (now Schneider Electric) in 1979 for use with its programmable logic controllers (PLCs). Modbus has become a de facto standard communication protocol and is now a commonly available means of connecting industrial electronic devices. The main reasons for the use of Modbus in the industrial environment are:

  • developed with industrial applications in mind;
  • openly published and royalty-free;
  • easy to deploy and maintain;
  • moves raw bits or words without placing many restrictions on vendors.

Modbus enables communication among many devices connected to the same network, for example, a system that measures temperature and humidity and communicates the results to a computer. Modbus is often used to connect a supervisory computer with a remote terminal unit (RTU) in supervisory control and data acquisition (SCADA) systems. Many of the data types are named from its use in driving relays: a single-bit physical output is called a coil, and a single-bit physical input is called a discrete input or a contact.

This article provides a brief example on how to use Modbus serial to monitor a slave device, send data to server and how to configure slave alarms. To find more information about this feature visit RUT955 Modbus and RUT955 RS232/RS485 pages.

Prerequisites

  • One RUT955 router
  • Windows 10 computer
  • Hercules and modRSsim applications
  • RS232 to USB cable

Topology

Networking rut955 configuration modbus serial topology 2 v1.png

Configuring Modbus serial slave device

In this example we are going to be using our Windows 10 computer as a slave. To do so you will need to install modRSsim application, which you can download here.

When you are done with that, open the app and apply the following configuration.

Networking rut955 configuration modbus serial 1 v1.png

  1. Select Protocol (MODBUS RS-232).
  2. Click Setup the communication Serial or TCP/IP port.

Networking rut955 configuration modbus serial 2 v1.png

  1. Select the Port which you connected RS232 cable to (to find which port you are using go to Windows search bar and write Device Manager then select Ports and see which one you are using).
  2. Select Parity (Even).
  3. Click OK.

Configuring Modbus serial master

Open router’s WebUI, navigate to Services > Modbus > Modbus Serial Master and apply the following configuration.

Networking rut955 configuration modbus serial 3 v1.png

  1. Press Enable.
  2. Select Baud rate (9600, it must match slave‘s baud rate).
  3. Select Parity (Even).
  4. Press Save.

Now create RS232 slave by writing a name, pressing Add button. It should appear like in the example and then press Edit.

Networking rut955 configuration modbus serial 4 v1.png

Then apply the following configuration.

Networking rut955 configuration modbus serial 5 v1.png

  1. Check Enable.
  2. Type in Slave ID (any number from 1 to 255).
  3. Add Period (Query period).
  4. Press Save.

Go back to the Slave configuration window and create Slave request by writing a name, pressing Add button. It should appear like in the example and then press Edit.

Networking rut955 configuration modbus serial 6 v1.png

Then apply the following configuration.

Networking rut955 configuration modbus serial 7 v1.png

  1. Check Enable.
  2. Select Function (Read Holding Registers).
  3. Write First register (1).
  4. Write Register count (10).
  5. Press Save.

Modbus data to server

Creating server


In order to test the functionality, you will need to set up a server (you can run a server on the same computer you use as a slave simulator).

There are many ways how you can create a server to which Modbus will send data to. In this example we are going to be using Windows 10 computer and Hercules app, which you can download here, to create a test server. Download, install the app and apply the configuration below:

Networking rut955 configuration modbus serial 8 v1.png

  1. Select TCP Server tab.
  2. Enter Port (In this example default 1883 is used).
  3. Click Listen

And that is it, now you will be able to see the data coming from Modbus in the Received data section.

RUT Modbus data to server configuration


In order to setup your router to send Modbus data to server you will need to navigate to Services > Modbus > Modbus Data to Server.

Networking rut955 configuration modbus serial 9 v1.png

  1. Select Protocol (In this example HTTP(S) will be used).
  2. Enter IP and port of the PC with the Hercules software.
  3. Enter Period (minutes, how often router should send data to server).
  4. Click ADD.

Then you will be redirected to Advanced sender settings.

Networking rut955 configuration modbus serial 10 v1.png

  1. Enter Name (It can be anything you want).
  2. Click Save.

Receiving data


Open Hercules again, press Listen and you should start receiving Modbus Data messages.

Networking rut955 configuration modbus serial 11 v1.png

Try to change some data in the Modbus Slave simulator.

Networking rut955 configuration modbus serial 12 v1.png

Received data should change.

Networking rut955 configuration modbus serial 13 v1.png

Slave alarms

In order to setup the following configuration SIM card is required.

Go back to Services > Modbus > Modbus Serial Master and press edit the same Slave configuration or create a new one. There will be section called Slave alarms. Create a name, then press Add button. When it appears like in the example, press Edit.

Networking rut955 configuration modbus serial 14 v1.png

Then apply the following configuration:

Networking rut955 configuration modbus serial 15 v1.png

  1. Enable instance.
  2. Select Function (Read Holding Registers).
  3. Write Register (1).
  4. Select Condition (More than).
  5. Write Value (5).
  6. Select Action (SMS).
  7. Write Phone number (the number you want to receive the messages to).
  8. Create Message (type anything you want to receive).
  9. Press Save.

Now go back to Modbus slave simulator and edit this window:

Networking rut955 configuration modbus serial 16 v1.png

Change the value to anything below 5, you should not receive messages. Then change the value to anything above 5, you should start receiving messages.