Template:Networking rut9xx manual vpn ipsec
To create a new IPsec instance, go to the Services → VPN → IPsec section, enter a custom name and click "Add". An IPsec instance with the given name will appear in the "IPsec Configuration" list.
To begin configuration, click the 'Edit' button located next to the instance.
The IPsec configuration section is used to configure the main parameters of an IPsec connection. Refer to the figure and table below for information on the configuration fields located in the general settings section.
|Enable||yes | no; default: no||Turns the IPsec instance on or off.|
|IKE version||IKEv1 | IKEv2; default: IKEv1||Internet Key Exchange (IKE) version used for key exchange.
|Mode||Main | Aggressive; default: Main||Internet Security and Key Management Protocol (ISAKMP) phase 1 exchange mode.
|Type||Tunnel | Transport; default: Tunnel||Type of connection.
|On startup||Ignore | Add | Route | Start; default: Start||Defines how the instance should act on router startup.
|My identifier||ip | string; default: none||Defines how the user (IPsec instance) will be identified during authentication.|
|Tunnel: Local IP address/Subnet mask||ip/netmask | default: none||Local IP address and subnet mask used to determine which part of the network can be accessed in the VPN network. Netmask range [0..32]. If left empty, IP address will be selected automatically.|
|Left firewall||off | on; default: on||Adds neccessary firewall rules to allow traffic of this IPsec instance on this router.|
|Force encapsulation||yes | no; default: no||Forces UDP encapsulation for ESP packets even if a "no NAT" situation is detected.|
|Dead Peer Detection||yes | no; default: no||A function used during Internet Key Exchange (IKE) to detect a "dead" peer. It used to reduce traffic by minimizing the number of messages when the opposite peer in unavailable and as failover mechanism.|
|Dead Peer Detection: Delay (sec)||integer; default: none||The frequency of checking whether a peer is still availaible or not.|
|Dead Peer Detection: Timeout (sec)||integer; default: none||Time limit after which the IPsec instance will stop checking the availability of a peer and determine it to be "dead" if no response is received.|
|Authentification type||Pre-shared key | X.509; default: Pre-shared key||Here you can choose authentification type accordingly to your IPSec configuration|
|Certificate file||.crt file; default: none||Uploads a certificate file.|
|Key file||.key file; default: none||Uploads a key file.|
|Right participant's certificate||.crt file; default: none||Right participant's certificate certificate is used to authenticate remote peer|
|CA certificate||.crt file; default: none||Uploads a Certificate authority (CA) file.|
|Pre shared key||string; default: none||A shared password used to authenticate between the peers|
|Use additional xauth authentification||yes | no; default: no||Adds additional xauth authentification options.|
|Xauth: Xauth password||string; default: none||Password for additional peer authentification.|
|Remote VPN endpoint||host | ip; default: none||IP address or hostname of the remote IPsec instance.|
|Remote identifier||ip | string; default: none||Defines remote IPsec instance identification.|
|Tunnel: Remote IP address/subnet mask||ip/netmask; default: none||Remote network IP address and subnet mask used to determine which part of the network can be accessed in the VPN network. Netmask range [0..32]. This value must differ from the device’s LAN IP.|
|Right firewall||yes | no; default: yes||Adds neccessary firewall rules to allow traffic of from the opposite IPsec instance on this router.|
|Transport: Use with DMVPN||yes | no; default: no||Adds several necessary options to make DMVPN work.|
|Passthrough networks||None | LAN | Wired | WiFi | Mobile | custom; default: none||Select networks which should be passthrough and excluded from routing through tunnel|
|Enable keepalive||yes | no; default: no||When enabled, the instance sends ICMP packets to the specified host at the specified frequency. If no response is received, the router will attempt to restart the connection.|
|Host||host | ip; default: none||Hostname or IP address to which keepalive ICMP packets will be sent to.|
|Ping period (sec)||integer [0..9999999]; default: none||The frequency at which keepalive ICMP packets will be sent to the specified host or IP address.|
|Allow WebUI access||yes | no; default: no||Allows WebUI access for hosts in the VPN network.|
|Custom options||ipsec options; default: none||Provides the possibility to further customize the connection by adding extra IPsec options.|
- Some configuration fields become available only when certain other parameters are selected. Different color codes are used for different parameters:
- Orange for Type: Xauth
- Red for Type: Tunnel
- Purple for Type: Transport
- Blue for Dead Peer Detection: Enabled
- After changing any of the parameters, don't forget to click the Save button located at the bottom-right side of the page.
IKE (Internet Key Exchange) is a protocol used to set up security associations (SAs) for the IPsec connection. This process is required before the IPsec tunnel can be established. It is done in two phases:
||Main mode (figure 1)
||Aggressive mode (figure 2)
|Figure 1||Figure 2|
|Encryption algorithm||DES | 3DES | AES128 | AES192 | AES256; default: 3DES||Algorithm used for data encryption.|
|Authentication/Hash algorithm||MD5 | SHA1 | SHA256 | SHA384 | SHA512; default: SHA1||Algorithm used for exchanging authentication and hash information.|
|DH group/PFS group||MODP768 | MODP1024 | MODP1536 | MODP2048 | MODP3072 | MODP4096; default: MODP1536||Diffie-Hellman (DH) group used in the key exchange process. Higher group numbers provide more security, but take longer and use more resources to compute the key.|
|Lifetime||integer; default: 8 hours||Defines a time period after which the phase will re-initiate its exchange of information.|
A pre-shared key is a secret password used for authentication between IPsec peers before a secure tunnel is established. To create a new key, click the 'Add' button.
The figure below is an example of the Pre-shared keys section and the table below provides information on configuration fields contained in that section:
|Pre-shared key||string; default: none||A shared password used for authentication between IPsec peers before a secure channel is established.|
|Secret's ID selector||string; default: none||Each secret can be preceded by a list of optional ID selectors. A selector is an IP address, a Fully Qualified Domain Name, user@FQDN or %any.
NOTE: IKEv1 only supports IP address ID selector.