Template:Networking rut manual gps

From Teltonika Networks Wiki
Revision as of 12:42, 30 July 2019 by Dziugas (talk | contribs) (Created page with "==Summary== The <b>Global Positioning System</b> (<b>GPS</b>) is a space-based radionavigation system. This chapter is an overview of the GPS service in {{{name}}} routers....")

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)

Summary

The Global Positioning System (GPS) is a space-based radionavigation system. This chapter is an overview of the GPS service in {{{name}}} routers.

Map

The Map page displays the device's current coordinates and position on the map. To see the device's location on the map, make sure to attach the GPS antenna on the router and enable GPS in the [[{{{name}}}_GPS#General|General]] page.

The figure below is an example of the Map page:

[[File:{{{file_map}}}]]

General

The General is used to enable the GPS service and the support for different types satellites. Once you turn on GPS, you can check the [[{{{name}}}_GPS#Map|Map]] page in order to see if the router has obtained a GPS fix. It is very important to attach the GPS antenna on the router and place it outside (not inside of a building). The router will not be likely to obtain a GPS fix otherwise.

The figure below is an example of the General page and the table below provides information on the fields contained in that page:

[[File:{{{file_general}}}]]

Field name Value Description
Enabled yes | no; Default: no Turns the GPS service ON or OFF
Galileo NMEA support* yes | no; Default: no Turns support for Galileo satellites ON or OFF
Glonass NMEA support* yes | no; Default: no Turns support for Glonass satellites ON or OFF
BeiDou NMEA support* yes | no; Default: no Turns support for BeiDou satellites ON or OFF

*Changing these options requires a modem reboot. Therefore, if you make changes to these options and save them, the router will lose cellular connectivity for about 30 seconds.

NMEA

The NMEA page is used to configure settings related to NMEA sentence collecting and forwarding.

NMEA forwarding


The NMEA forwarding section is used to configure and enable NMEA forwarding. The figure below is an example of the NMEA forwarding section and the table below provides information on the fields contained in that section:

[[File:{{{file_nmea_forwarding}}}]]

Field name Value Description
Enabled yes | no; Default: no Turns NMEA forwarding ON or OFF
Hostname ip | host; Default: 192.168.1.5 IP address or hostname of the server to which NMEA data will be forwarded to
Port integer [0..65535]; Default: 8500 Port number to which NMEA data will be forwarded to
Protoocl TCP | UDP; Default: TCP Protocol that will be used to send NMEA data

NMEA forwarding cache


The router caches NMEA forwarding information if NMEA forwarding is enabled. This section is used to select the memory type where the cache will be stored and the maximum amount of data that will be saved:

[[File:{{{file_nmea_cache}}}]]

Field name Value Description
Type ram | flash; Default: ram Selects which type of memory will be used for storing NMEA forwarding cache
Maximum sentences integer; Default: 5000 Maximum amount of NMEA sentences that will be saved in the cache before older entries are replaced by new ones
File filepath; default: none Location of the file where NMEA forwarding cache information will be stored. This field becomes visible only when the selected memory type is "flash"

NMEA collecting


The NMEA collecting section is used to enable NMEA sentence gathering and storing. The figure below is an example of the NMEA collecting section and the table below provides information on the fields contained in that section:

[[File:{{{file_nmea_collecting}}}]]

Field name Value Description
Enabled yes | no; Default: no Turns NMEA sentence collecting ON or OFF
Location filepath; Default: none Location of the file where NMEA sentences will be stored. This field becomes visible only when NMEA collecting is enabled

NMEA sentence settings


The NMEA sentence settings section provides the possibility to configure which NMEA sentences will be forwarded or collected and at what frequency. The figure below is an example of the NMEA sentence settings section and the table below provides information on the fields contained in that section:

[[File:{{{file_nmea_sentence}}}]]

Field name Value Description
Forwarding enabled yes | no; Default: no Enables forwarding for selected NMEA sentence
Forwarding interval integer; Default: 5 NMEA sentence forwarding frequency in seconds
Collecting enabled yes | no; Default: no Enables collecting for selected NMEA sentences
Collecting interval integer; Default: 5 NMEA sentence collecting frequency in seconds


NMEA sentence refference table:

NMEA sentence name Description
GPGSV Number of GPS satellites in view
GPGGA GPS fix data
GPVTG Track made good and speed relative to the ground
GPRMC Recommended minimum specific GPS/Transit data
GPGSA GPS DOP and active satellites
GLGSA GLONASS DOP and active satellites
GLGSV Number of GLONASS satellites in view
GNGNS GNSS position fix from more than one constellation (e.g., GPS + GLONASS)
GAGSV Number of Galileo satelites in view
PQGSV Detailed satellite data (used in BeiDou sentences)
PQGSA Overall satellite data (used in BeiDou sentences)

HTTPS

The HTTPS page can be used to configure data sending to an HTTP(S) server.

HTTPS/HTTP Server Settings


The HTTPS/HTTP Server Settings section is used to enable GPS data sending to an HTTP or HTTPS server:

[[File:{{{file_https_settings}}}]]

Field name Value Description
Enabled yes | no; Default: no Turns data sending to HTTP/HTTPS ON or OFF
URL ip | host; Default: 192.168.1.5 IP address or hostname of the HTTP/HTTPS server

TAVL Settings


The TAVL Settings section is used to select which data will be sent to the TAVL server:

[[File:{{{file_tavl_settings}}}]]

field name value description
Send GSM signal yes | no; Default: no Includes GSM signal strength information in GPS data package to be sent to server
Send analog input yes | no; Default: no Includes analog input state in GPS data package to be sent to server
Send digital input (1) yes | no; Default: no Includes digital input #1 state in GPS data package to be sent to server
Send digital input (2) yes | no; Default: no Includes digital input #2 state in GPS data package to be sent to server

AVL

The AVL page is used to set up GPS data sending to an AVL server.

AVL Server Settings


The AVL Server Settings section is used to configure the main parameters of data sending to an AVL server. The figure below is an example of the AVL Server Settings section and the table below provides information on the fields contained in that section:

[[File:{{{file_avl_settings}}}]]

Field name Value Description
Enabled yes | no; Default: no Turns data sending to AVL server ON or OFF
Hostname ip | host; Default: 192.168.1.5 IP address or hostname of the AVL server
Port integer [0..65535]; Default: 8500 Port number of the AVL server to which router will be connecting to
Protoocl TCP | UDP; Default: TCP Protocol that will be used for communication with the AVL server

Main rule


[[File:{{{file_main_rule}}}]]

Secondary Rules


[[File:{{{file_secondary_rules}}}]]

GPS Configuration


[[File:{{{file_gps_configuration}}}]]

TAVL Settings


The TAVL Settings section is used to select which data will be sent to the TAVL server:

[[File:{{{file_tavl_settings}}}]]

field name value description
Send GSM signal yes | no; Default: no Includes GSM signal strength information in GPS data package to be sent to server
Send analog input yes | no; Default: no Includes analog input state in GPS data package to be sent to server
Send digital input (1) yes | no; Default: no Includes digital input #1 state in GPS data package to be sent to server
Send digital input (2) yes | no; Default: no Includes digital input #2 state in GPS data package to be sent to server

GPS Geofencing

A geofence is a virtually defined boundary for a real-world geographic area. The GPS Geofencing page provides you with the possibility to set this custom area and apply rules that will inform you when the device leaves or enters the geofence.

[[File:{{{file_geofencing_add}}}]]

The figure below is an example of GPS Geofencing configuration and the table below provides information related to that configuration:

[[File:{{{file_geofencing_details}}}]]

Field name Value Description
Enable yes | no; Default: no Turns the Geofence rule ON or OFF
Longitude (X) degrees [-180.000000..180.000000]; Default: 0.000000 East-west position of a point on the Earth's surface. Combining this and the Latitude information will produce a point on the world map that will serve as the center of the geofence area
Latitude (Y) degrees [-90.000000..90.000000]; Default: 0.000000 North-south position of a point on the Earth's surface. Combining this and the Longitude information will produce a point on the world map that will serve as the center of the geofence area
Radius integer [1..999999]; Default: 200 Radius (in meters) of the geofence area
Generate event on Exit | Enter | Enter/Exit; Default: Exit Specifies whether the rule should be triggered when the device enters the geofence area, leaves it or on both events
Get current coordinates - (interactive button) Obtains the device's current coordinates and places them in the Longitude and Latitude fields

See also

  • [[{{{name}}}_Protocols|{{{name}}} GPS protocols]]

[[Category:{{{name}}} WebUI]]