Difference between revisions of "Template:Networking rutxxx configuration example use LAN as WAN"

From Teltonika Networks Wiki
Tags: Mobile edit Mobile web edit
 
(20 intermediate revisions by 2 users not shown)
Line 9: Line 9:
 
* One RUTxxx series router (excluding [[RUT850]]).
 
* One RUTxxx series router (excluding [[RUT850]]).
 
* At least two wired Internet connections.
 
* At least two wired Internet connections.
* An end device for test the configuration.
+
* An end device for test the configuration.<br>
<br>
 
 
'''Configuration scheme:'''
 
'''Configuration scheme:'''
[[File:{{{image}}}|border|class=tlt-border]]
+
[[File:{{{file_scheme}}}|border|class=tlt-border]]
 +
 
 
==WebUI Router configuration==
 
==WebUI Router configuration==
 
Connect to the router’s WebUI navigate to '''Network -> VLAN -> LAN Network''' and create a new interface by entering name and clicking '''Add New'''.<br>
 
Connect to the router’s WebUI navigate to '''Network -> VLAN -> LAN Network''' and create a new interface by entering name and clicking '''Add New'''.<br>
[[File:LAN_TO_WAN02.jpg|border|class=tlt-border]]<br>
+
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_1_v3.png|border|class=tlt-border]]<br>
 
After you clicked '''Add New''' new configuration window will pop-up, there you leave as default and press '''Save.'''
 
After you clicked '''Add New''' new configuration window will pop-up, there you leave as default and press '''Save.'''
[[File:LANASWAN02.jpg|border|class=tlt-border|600px]]
+
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_2_v1.png|border|class=tlt-border]]<br>
 
After saving settings, you will be redirected back to '''Network -> VLAN -> VLAN Networks''', now you need to open VLAN Network tab in the same window and you will need to:
 
After saving settings, you will be redirected back to '''Network -> VLAN -> VLAN Networks''', now you need to open VLAN Network tab in the same window and you will need to:
 
<ul>
 
<ul>
Line 28: Line 28:
 
<i> '''Note: Make sure that you are not connected to that LAN port which you going to disable.'''</i>
 
<i> '''Note: Make sure that you are not connected to that LAN port which you going to disable.'''</i>
 
<li>New LAN_WAN interface:<br>
 
<li>New LAN_WAN interface:<br>
- Click '''Add''' and new row will appear.<br>
+
- Click '''Add''' and a new row will appear.<br>
 
- Turn off LAN ports 1-2 and leave only LAN port 3 on.<br>
 
- Turn off LAN ports 1-2 and leave only LAN port 3 on.<br>
- Select “lan_wan” in the LAN section and press '''Save'''.</li><br>
+
- Select your newly created interface in the LAN section and click '''Save'''.</li>
[[File:LANASWAN003.jpg|border|class=tlt-border|600px]]
 
 
</ul>
 
</ul>
===Using DCHP===
+
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_3_v1.png|border|class=tlt-border]]
Leave the settings as default and click '''save'''<br>
 
[[File:LANASWAN009.jpg|border|class=tlt-border|600px]]
 
===Using a Static IP===
 
<li style="color: red;">'''Note: Just if you want to use a Static IP, see the instructions below.'''</li>
 
'''Static IP need to be set as router’s WAN IP.'''
 
Static IP should be in the same subnet as gateway’s LAN interface.<br>
 
For example: if gateway’s LAN subnet is 192.168.10.1, then router’s WAN IP could be for example '''192.168.10.125'''</div>
 
[[File:LANASWAN04.jpg|border|class=tlt-border]]
 
 
==CLI/SSH Router configuration==
 
==CLI/SSH Router configuration==
For the next part you will be configuring router via SSH. For this you need to use the command line interface (CLI) or a SSH software if you’re using Windows or iOS. In this example software '''putty''' will be used. Open '''putty''' enter routers LAN IP address and press '''Open'''.<br>
+
 
[[File:LANASWAN005.jpg|border|class=tlt-border|400px]]
+
The next step of the configuration will be done over SSH/CLI. For this example we'll be using "PuTTY" - a free SSH client that can run on Windows.
After clicking '''Open''' you will need to enter router credentials.
+
 
<li>Login as: '''root'''</li>
+
Open "PuTTY", enter the router's LAN IP address into the "Host Name (or IP Address)" field and click 'Open'.
<li>Password: routers admin password (by default admin01)</li>
+
 
[[File:LANASWAN06.jpg|thumb]]<br>
+
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_8_v1.png]]
Now when you are connected you will need to make changes to network settings, this will be
+
 
achieved via SSH command: '''vi''', which allows you to edit settings in the router. Enter following
+
Next, enter the login credentials:
command in SSH:
+
 
<li>'''vi /etc/config/network''' press latter '''i''' to be able to edit.</li>
+
login as: <b>root</b>
===Using DHCP===
+
[email protected]'s password: <b><admin_password></b>
Using arrows navigate and find '''config interface 'lan_wan'''' and add two options:  
+
 
<li>1. '''option proto 'dhcp''''</li>
+
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_9_v1.png]]
<li>2. '''option ifname 'eth0.1''''</li>
+
 
<li>3. '''option backup '1''''</li>
+
Next, we'll have to edit the <b><i>network</i></b> config file using the built-in "vi" text editor. To begin editing the <i>network</i> config file:
<li>4. '''option metric '10''''</li>
+
 
[[File:Lanaswan010.jpg|border|class=tlt-border]]<br>
+
vi /etc/config/network
===Using Static IP===
+
 
Using arrows navigate and find '''config interface 'lan_wan'''' and add two options:  
+
Then hit the "I" key on your keyboard to enable editing.
<li>1. '''option gateway '192.168.10.1''''</li>
+
 
<li>2. '''option dns '8.8.8.8''''</li>
+
There are two distinct configurations described below. One is a [[#Static_IP|static IP]] configuration for setting the new WAN port manually, the other is [[#DHCP|DHCP]] - for automatic network configuration of the new WAN port. Follow only the instruction that suits your needs.
<li>3. '''option backup '1''''</li>
+
 
<li>4. '''option metric '10''''</li>
+
===DHCP===
[[File:LANASWAN006.jpg|border|class=tlt-border]]<br>
+
----
Press '''Esc''' and write ''':wq'''.
+
Using the arrow keys on your keyboard, navigate and find <i>config interface 'lan_wan'</i> erase the current configuration and write these options:  
After that you will need to restart network service on the router, for this use command:
+
 
<li>'''/etc/init.d/network restart'''</li><br>
+
option proto 'dhcp'
[[File:LANASWAN007.jpg|border|class=tlt-border]]<br>
+
option ifname 'eth0.1'
After restart is completed go back to routers WebUI and navigate to '''Network -> Firewall -> General Settings'''.
+
option backup '1'
Scroll down, in '''Zone Forwarding''' find source zone '''lan_wan''' and change “Default forwarding action” from '''reject''' to '''accept''' and also check '''Masquerading''' and save settings.<br>
+
option metric '10'
[[File:008-2.jpg|border|class=tlt-border|800px]]<br>
+
 
 +
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_4_v1.png]]
 +
 
 +
===Static IP===
 +
----
 +
Using arrows navigate and find <i>config interface 'lan_wan'</i> leave the current configuration and add these four options:
 +
 
 +
option gateway '192.168.10.1'
 +
option dns '8.8.8.8'
 +
option backup '1'
 +
option metric '10'
 +
 
 +
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_5_v1.png]]
 +
----
 +
To exit the "vi" editor, press the "Esc" key, type in <i>:wq</i> and hit "Enter". While still on the command line, restart the <i>network</i> service on the router - this will apply the changes made to the configuration. Use this command:
 +
 
 +
/etc/init.d/network restart
 +
 
 +
Next go back to the WebUI and navigate to <i>Network Firewall → <b>General Settings</b></i> page. Scroll down to the "Zone Forwarding" section to find source zone 'lan_wan' and change the following:
 +
 
 +
<ul>
 +
    <li><b>Default forwarding action</b>: accept</li>
 +
    <li><b>Masquerading</b>: on</li>
 +
    <li><b>Save</b> changes</li>
 +
</ul>
 +
 
 +
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_6_v1.png|border|class=tlt-border]]
 +
 
 
==Testing the configuration==
 
==Testing the configuration==
 
If you did the steps in the right way, your end device should have internet connection according the scheme.<br>
 
If you did the steps in the right way, your end device should have internet connection according the scheme.<br>
Go to '''Network --> WAN''' and check if the new LAN_WAN is enable and if it has an assigned IP<br>
+
Go to '''Network --> WAN''' and check if the new LAN_WAN is enable and if it has an assigned IP.
[[File:WAN.jpg|border|class=tlt-border|800px]]
+
<li>Set up your WAN as a main connection</li>
 +
<li>Set up your configured LAN port as WAN failover backup.</li>
 +
[[File:Networking_rutxxx_configuration_examples_use_lan_as_wan_7_v1.png|border|class=tlt-border]]<br>
 +
<li>Go to '''www.whatsmyip.com''' and check your public IP.</li>
 +
[[File:0011.png|border|class=tlt-border|960px]]
 +
<li>After that, unplug the WAN cable and check again your Public IP. Your end device should have internet connection and a differt public IP</li>
 +
[[File:0012.png|border|class=tlt-border|960px]]<br>
 +
<li>So, plug again the WAN internet connection and wait a few seconds. The public IP should change again to the first IP shown.</li>
 
[[Category:{{{name}}} Configuration Examples]]
 
[[Category:{{{name}}} Configuration Examples]]

Latest revision as of 13:19, 1 October 2021

Introduction

The information in this page is updated in accordance with the [[Media:{{{fw_version}}}_WEBUI.bin|{{{fw_version}}}]] firmware version.
This article provides a guide on how to configure the LAN ports as WAN. It can be usefull as wired ISP redundant connection or even to change the port for physical damage or a custom mounting.

Configuration overview and prerequisites

Before we begin, let's overview the configuration that we are attempting to achieve and the prerequisites that make it possible. Prerequisites:

  • One RUTxxx series router (excluding RUT850).
  • At least two wired Internet connections.
  • An end device for test the configuration.

Configuration scheme: [[File:{{{file_scheme}}}|border|class=tlt-border]]

WebUI Router configuration

Connect to the router’s WebUI navigate to Network -> VLAN -> LAN Network and create a new interface by entering name and clicking Add New.
Networking rutxxx configuration examples use lan as wan 1 v3.png
After you clicked Add New new configuration window will pop-up, there you leave as default and press Save. Networking rutxxx configuration examples use lan as wan 2 v1.png
After saving settings, you will be redirected back to Network -> VLAN -> VLAN Networks, now you need to open VLAN Network tab in the same window and you will need to:

  • Select VLAN mode: Port based
  • Current LAN interface:
    - Enable wireless access
    - Select your current LAN interface.
    - Turn off LAN port 3 (which will be used as WAN port)
    - Press Save.
  • Note: Make sure that you are not connected to that LAN port which you going to disable.
  • New LAN_WAN interface:
    - Click Add and a new row will appear.
    - Turn off LAN ports 1-2 and leave only LAN port 3 on.
    - Select your newly created interface in the LAN section and click Save.

Networking rutxxx configuration examples use lan as wan 3 v1.png

CLI/SSH Router configuration

The next step of the configuration will be done over SSH/CLI. For this example we'll be using "PuTTY" - a free SSH client that can run on Windows.

Open "PuTTY", enter the router's LAN IP address into the "Host Name (or IP Address)" field and click 'Open'.

Networking rutxxx configuration examples use lan as wan 8 v1.png

Next, enter the login credentials:

login as: root
[email protected]'s password: <admin_password>

Networking rutxxx configuration examples use lan as wan 9 v1.png

Next, we'll have to edit the network config file using the built-in "vi" text editor. To begin editing the network config file:

vi /etc/config/network

Then hit the "I" key on your keyboard to enable editing.

There are two distinct configurations described below. One is a static IP configuration for setting the new WAN port manually, the other is DHCP - for automatic network configuration of the new WAN port. Follow only the instruction that suits your needs.

DHCP


Using the arrow keys on your keyboard, navigate and find config interface 'lan_wan' erase the current configuration and write these options:

option proto 'dhcp'
option ifname 'eth0.1'
option backup '1'
option metric '10'

Networking rutxxx configuration examples use lan as wan 4 v1.png

Static IP


Using arrows navigate and find config interface 'lan_wan' leave the current configuration and add these four options:

option gateway '192.168.10.1'
option dns '8.8.8.8'
option backup '1'
option metric '10'

Networking rutxxx configuration examples use lan as wan 5 v1.png


To exit the "vi" editor, press the "Esc" key, type in :wq and hit "Enter". While still on the command line, restart the network service on the router - this will apply the changes made to the configuration. Use this command:

/etc/init.d/network restart

Next go back to the WebUI and navigate to Network → Firewall → General Settings page. Scroll down to the "Zone Forwarding" section to find source zone 'lan_wan' and change the following:

  • Default forwarding action: accept
  • Masquerading: on
  • Save changes

Networking rutxxx configuration examples use lan as wan 6 v1.png

Testing the configuration

If you did the steps in the right way, your end device should have internet connection according the scheme.
Go to Network --> WAN and check if the new LAN_WAN is enable and if it has an assigned IP.

  • Set up your WAN as a main connection
  • Set up your configured LAN port as WAN failover backup.
  • Networking rutxxx configuration examples use lan as wan 7 v1.png

  • Go to www.whatsmyip.com and check your public IP.
  • 0011.png

  • After that, unplug the WAN cable and check again your Public IP. Your end device should have internet connection and a differt public IP
  • 0012.png

  • So, plug again the WAN internet connection and wait a few seconds. The public IP should change again to the first IP shown.
  • [[Category:{{{name}}} Configuration Examples]]