Difference between revisions of "Template:Networking trb manual static routes"
(Created page with "__TOC__ ==Summary== <b>Static routes</b> specify over which interface and gateway a certain host or network can be reached. This chapter is an overview of the Static Routes p...") |
|||
Line 14: | Line 14: | ||
[[File:{{{file_routes}}}]] | [[File:{{{file_routes}}}]] | ||
+ | <table class="nd-mantable"> | ||
+ | <tr> | ||
+ | <th>Field</th> | ||
+ | <th>Dalue</th> | ||
+ | <th>Description</th> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>Interface</td> | ||
+ | <td>mobile | lan; default: <b>mobile</b></td> | ||
+ | <td>The zone where the target network resides</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>Target<span class="asterisk">*</span>'</td> | ||
+ | <td>ip4; default: <b>0.0.0.0</b></td> | ||
+ | <td>The address of the destination network</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>Netmask<span class="asterisk">*</span></td> | ||
+ | <td>netmask; default: <b>255.255.255.255</b></td> | ||
+ | <td>A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>Gateway</td> | ||
+ | <td>ip; default: <b>none</b></td> | ||
+ | <td>Defines where the router should send all the traffic that applies to the rule</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>Metric</td> | ||
+ | <td>integer; default: <b>0</b></td> | ||
+ | <td>The <b>metric</b> value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the lower metric is applied.</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>MTU</td> | ||
+ | <td>integer; default: <b>1500</b></td> | ||
+ | <td></td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>Route Type</td> | ||
+ | <td>unicast | local | broadcast | multicast | unreachable | prohibit | backhole | anycast | -- custom -- ; default: <b>unicast</b></td> | ||
+ | <td></td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | <span class="asterisk">*</span><b>Additional notes on Target & Netmask:<b> | ||
+ | |||
+ | You can define a rule that applies to a single IP like this: Destination - some IP; Netmask - 255.255.255.255. Furthermore, you can define a rule that applies to a segment of IPs like this: Destination – some IP that STARTS some segment; Netmask – Netmask that defines how large the segment is. e.g.: | ||
+ | <table class="nd-mantable"> | ||
+ | <tr> | ||
+ | <th>Field</th> | ||
+ | <th>Value</th> | ||
+ | <th>Description</th> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>192.168.2.161</td> | ||
+ | <td>255.255.255.255</td> | ||
+ | <td>Only applies to 192.168.2.161.</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>192.168.2.0</td> | ||
+ | <td>255.255.255.240</td> | ||
+ | <td>Applies to IPs in the 192.168.2.0 - 192.168.2.15 range.</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>192.168.2.240</td> | ||
+ | <td>255.255.255.240</td> | ||
+ | <td>Applies to IPs in the 192.168.2.240 - 192.168.2.255 range.</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>192.168.2.161</td> | ||
+ | <td>255.255.255.0</td> | ||
+ | <td>Applies to IPs in the 192.168.2.0 - 192.168.55.255 range.</td> | ||
+ | </tr> | ||
+ | <tr> | ||
+ | <td>192.168.0.0</td> | ||
+ | <td>255.255.0.0</td> | ||
+ | <td>Applies to IPs in the 192.168.0.0 - 192.168.255.255 range.</td> | ||
+ | </tr> | ||
+ | </table> | ||
[[Category:{{{name}}} WebUI]] | [[Category:{{{name}}} WebUI]] |
Revision as of 16:32, 18 October 2019
Summary
Static routes specify over which interface and gateway a certain host or network can be reached. This chapter is an overview of the Static Routes page in {{{name}}} gateways.
The information in this page is updated in accordance with the [[Media:{{{fw_version}}}.bin|{{{fw_version}}}]] firmware version.
Static routes
To find information on static route configuration, refer to the figure and table below:
[[File:{{{file_routes}}}]]
Field | Dalue | Description |
---|---|---|
Interface | mobile | lan; default: mobile | The zone where the target network resides |
Target*' | ip4; default: 0.0.0.0 | The address of the destination network |
Netmask* | netmask; default: 255.255.255.255 | A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies |
Gateway | ip; default: none | Defines where the router should send all the traffic that applies to the rule |
Metric | integer; default: 0 | The metric value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the lower metric is applied. |
MTU | integer; default: 1500 | |
Route Type | unicast | local | broadcast | multicast | unreachable | prohibit | backhole | anycast | -- custom -- ; default: unicast |
*Additional notes on Target & Netmask:
You can define a rule that applies to a single IP like this: Destination - some IP; Netmask - 255.255.255.255. Furthermore, you can define a rule that applies to a segment of IPs like this: Destination – some IP that STARTS some segment; Netmask – Netmask that defines how large the segment is. e.g.:
Field | Value | Description |
---|---|---|
192.168.2.161 | 255.255.255.255 | Only applies to 192.168.2.161. |
192.168.2.0 | 255.255.255.240 | Applies to IPs in the 192.168.2.0 - 192.168.2.15 range. |
192.168.2.240 | 255.255.255.240 | Applies to IPs in the 192.168.2.240 - 192.168.2.255 range. |
192.168.2.161 | 255.255.255.0 | Applies to IPs in the 192.168.2.0 - 192.168.55.255 range. |
192.168.0.0 | 255.255.0.0 | Applies to IPs in the 192.168.0.0 - 192.168.255.255 range. |
[[Category:{{{name}}} WebUI]]