Difference between revisions of "Template:Networking trb manual static routes"
From Teltonika Networks Wiki
| Line 17: | Line 17: | ||
<tr> | <tr> | ||
<th>Field</th> | <th>Field</th> | ||
| − | <th> | + | <th>Value</th> |
<th>Description</th> | <th>Description</th> | ||
</tr> | </tr> | ||
| Line 57: | Line 57: | ||
</table> | </table> | ||
| − | <span class="asterisk">*</span><b>Additional notes on Target & Netmask:<b> | + | <span class="asterisk">*</span><b>Additional notes on Target & Netmask:</b> |
| + | ---- | ||
| + | You can define a rule that applies to a single IP like this: | ||
| + | |||
| + | <ul> | ||
| + | <li><b>Target</b>: some IP</li> | ||
| + | <li><b>Netmask</b>: 255.255.255.255</li> | ||
| + | </ul> | ||
| + | |||
| + | Furthermore, you can define a rules that apply to a range of IPs. Refer to the table below for examples. | ||
| − | |||
<table class="nd-mantable"> | <table class="nd-mantable"> | ||
<tr> | <tr> | ||
| − | <th> | + | <th>Target</th> |
| − | <th> | + | <th>Netmask</th> |
<th>Description</th> | <th>Description</th> | ||
</tr> | </tr> | ||
Revision as of 16:37, 18 October 2019
Summary
Static routes specify over which interface and gateway a certain host or network can be reached. This chapter is an overview of the Static Routes page in {{{name}}} gateways.
The information in this page is updated in accordance with the [[Media:{{{fw_version}}}.bin|{{{fw_version}}}]] firmware version.
Static routes
To find information on static route configuration, refer to the figure and table below:
[[File:{{{file_routes}}}]]
| Field | Value | Description |
|---|---|---|
| Interface | mobile | lan; default: mobile | The zone where the target network resides |
| Target*' | ip4; default: 0.0.0.0 | The address of the destination network |
| Netmask* | netmask; default: 255.255.255.255 | A Mask that is applied to the Target to determine to what actual IP addresses the routing rule applies |
| Gateway | ip; default: none | Defines where the router should send all the traffic that applies to the rule |
| Metric | integer; default: 0 | The metric value is used as a sorting measure. If a packet about to be routed fits two rules, the one with the lower metric is applied. |
| MTU | integer; default: 1500 | |
| Route Type | unicast | local | broadcast | multicast | unreachable | prohibit | backhole | anycast | -- custom -- ; default: unicast |
*Additional notes on Target & Netmask:
You can define a rule that applies to a single IP like this:
- Target: some IP
- Netmask: 255.255.255.255
Furthermore, you can define a rules that apply to a range of IPs. Refer to the table below for examples.
| Target | Netmask | Description |
|---|---|---|
| 192.168.2.161 | 255.255.255.255 | Only applies to 192.168.2.161. |
| 192.168.2.0 | 255.255.255.240 | Applies to IPs in the 192.168.2.0 - 192.168.2.15 range. |
| 192.168.2.240 | 255.255.255.240 | Applies to IPs in the 192.168.2.240 - 192.168.2.255 range. |
| 192.168.2.161 | 255.255.255.0 | Applies to IPs in the 192.168.2.0 - 192.168.55.255 range. |
| 192.168.0.0 | 255.255.0.0 | Applies to IPs in the 192.168.0.0 - 192.168.255.255 range. |
[[Category:{{{name}}} WebUI]]
