123
edits
Changes
no edit summary
<p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.4'''] firmware version .</p>
<p style="color:red">The information in this page is updated in accordance with [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.08'''] firmware version.</p>
==Introduction==
==Introduction==
This article contains instructions on how to set up LAN port as WAN on RUTxxx if you have a need for multiple wired WAN connections.
This article contains instructions on how to set up LAN port as WAN on RUTxxx if you have a need for multiple wired WAN connections.
[[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]]
[[File:Networking_rutos_manual_webui_basic_advanced_mode_75.gif|border|center|class=tlt-border|1102x93px]]
==Configuration overview and prerequisites==
==Configuration overview and prerequisites==
* On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
* On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
* After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
* After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
[[File:VLAN config.png|border|center|class=tlt-border|798x239px]]
[[File:RutOS_Lan_as_Wan_VLAN_config.png|border|center|class=tlt-border|798x239px]]
===Add new WAN interface===
===Add new WAN interface===
----
----
Go to <strong>Network > Interfaces</strong> WebUI section.
Go to <strong>Network > WAN</strong> WebUI section.
* Click on <strong>Add</strong> button.
* Click on <strong>Add</strong> button.
[[File:New interface.png|border|center|class=tlt-border|901x453px]]
[[File:RutOS_Lan_as_Wan_WAN_ADD.png|border|center|class=tlt-border|901x453px]]
----
----
After doing that you will be redirected to new window to set up new interface, when there:
After doing that you will be redirected to new window to set up new interface, when there:
* Choose <strong>DHCP</strong> Protocol from drop-down list.
* Choose <strong>DHCP</strong> Protocol from drop-down list.
[[File:RutOS_Lan_as_Wan_WAN_DHCP.png|border|center|class=tlt-border|870x261px]]
[[File:DHCP settings.png|border|center|class=tlt-border|870x261px]]
If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify:
If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify:
* IPv4 address
* IPv4 address
* IPv4 broadcast
* IPv4 broadcast
* DNS servers
* DNS servers
[[File:Static IP.png|border|center|class=tlt-border|848x351px]]
[[File:RutOS_Lan_as_Wan_WAN_static.png|border|center|class=tlt-border|848x351px]]
----
----
* From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
* From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
* Press <strong>Apply & Save</strong>.
* Press <strong>Apply & Save</strong>.
[[File:Physical interface.png|border|center|class=tlt-border|866x281px]]
[[File:RutOS_Lan_as_Wan_WAN_physical.png|border|center|class=tlt-border|866x281px]]
==Check new WAN interface==
==Check new WAN interface==
Insert WAN cable in selected port, go to <strong>Network > Interfaces</strong> WebUI section and if you followed steps correctly yours newly created WAN interface should be running and have an IP.
Insert WAN cable in selected port, go to <strong>Network > WAN</strong> WebUI section and if you followed steps correctly yours newly created WAN interface should be running and have an IP.
[[File:Network rutos manual lan as wan check.png|border|class=tlt-border]]
[[File:RutOS_Lan_as_Wan_WAN_status.png|border|class=tlt-border]]
==Testing the configuration==
==Testing the configuration==