Line 1: |
Line 1: |
− | | + | <p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.4'''] firmware version .</p> |
| ==Introduction== | | ==Introduction== |
| | | |
− | This article contains instructions on how to set up LAN port as WAN on RUTOS if you have a need for multiple wired WAN connections. | + | This article contains instructions on how to set up LAN port as WAN on RUTxxx if you have a need for multiple wired WAN connections. |
| | | |
| [[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]] | | [[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]] |
| + | |
| + | ==Configuration overview and prerequisites== |
| + | |
| + | Before we begin, let's overview the configuration that we are attempting to achieve and the prerequisites that make it possible. |
| + | |
| + | '''Prerequisites''': |
| + | * One RUTxxx series router. |
| + | * At least two wired Internet connections. |
| + | * An end device for test the configuration.<br> |
| + | |
| + | '''Configuration scheme:''' |
| + | |
| + | [[File:Networking_rut955_configuration_examples_lan_port_as_wan_scheme_v1.png|border|class=tlt-border]] |
| | | |
| ==Setting up second WAN interface== | | ==Setting up second WAN interface== |
| | | |
− | To change LAN port purpose to WAN you will have to perform changes in 3 different locations of {{{name}}} WebUI | + | To change LAN port purpose to WAN you will have to perform changes in 3 different locations of RUTxxx WebUI |
| | | |
| ===Creating additional VLAN=== | | ===Creating additional VLAN=== |
Line 14: |
Line 27: |
| | | |
| Go to <strong>Network > VLAN</strong> section in device WebUI and perform following actions: | | Go to <strong>Network > VLAN</strong> section in device WebUI and perform following actions: |
− | # Create new <strong>VLAN ID</strong> by clicking <strong>ADD</strong> button.
| + | * Create new <strong>VLAN ID</strong> by clicking <strong>ADD</strong> button. |
− | # On VLAN ID: 1 (LAN interface), select <strong>Off</strong> from drop-down list, on port that you want to use as secondary WAN.
| + | * On VLAN ID: 1 (LAN interface), select <strong>Off</strong> from drop-down list, on port that you want to use as secondary WAN. |
− | # On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port.
| + | * On newly created VLAN ID (3 in this example), from drop-down list, select <strong>Untagged</strong>, on same port. |
− | # After performing these actions press <strong>Save & Apply</strong> in VLAN settings.
| + | * After performing these actions press <strong>Save & Apply</strong> in VLAN settings. |
− | [[File:Network RUTOS manual lan as wan vlan.png|border|class=tlt-border|1102px]] | + | [[File:VLAN config.png|border|center|class=tlt-border|798x239px]] |
− | | |
| ===Add new WAN interface=== | | ===Add new WAN interface=== |
| ---- | | ---- |
| | | |
| Go to <strong>Network > Interfaces</strong> WebUI section. | | Go to <strong>Network > Interfaces</strong> WebUI section. |
− | # Enter new <strong>Interface Name</strong>.
| + | * Enter new <strong>Interface Name</strong>. |
− | # Click on <strong>Add</strong> button.
| + | * Click on <strong>Add</strong> button. |
− | [[File:Network RUTOS manual lan as wan create interface.png|border|class=tlt-border|1102px]] | + | [[File:New interface.png|border|center|class=tlt-border|901x453px]] |
| ---- | | ---- |
| | | |
| After doing that you will be redirected to new window to set up new interface, when there: | | After doing that you will be redirected to new window to set up new interface, when there: |
− | # Choose <strong>DHCP</strong> Protocol from drop-down list.
| + | * Choose <strong>DHCP</strong> Protocol from drop-down list. |
− | # Press on <strong>Switch Protocol</strong>.
| + | * Press on <strong>Switch Protocol</strong>. |
− | [[File:Network RUTOS manual lan as wan interface setup dhcp.png|border|class=tlt-border|1102px]] | + | [[File:DHCP settings.png|border|center|class=tlt-border|870x261px]] |
| + | If there is need to use a '''static IP''' instead of '''DHCP option''' select '''Static''' option and specify: |
| + | * IPv4 address |
| + | * IPv4 netmask |
| + | * IPv4 gateway |
| + | * IPv4 broadcast |
| + | * DNS servers |
| + | [[File:Static IP.png|border|center|class=tlt-border|848x351px]] |
| ---- | | ---- |
| | | |
| After switching protocol More setting options will appear. | | After switching protocol More setting options will appear. |
− | # Go to <strong>Physical Settings</strong>.
| + | * Go to <strong>Physical Settings</strong>. |
− | # From drop-down list choose previously created VLAN interface (in this example it is eth0.3)
| + | * From drop-down list choose previously created VLAN interface (in this example it is eth0.3) |
− | # Press <strong>Apply & Save</strong>.
| + | * Press <strong>Apply & Save</strong>. |
− | [[File:Network RUTOS manual lan as wan interface physical settings.png|border|class=tlt-border|1102px]] | + | [[File:Physical interface.png|border|center|class=tlt-border|866x281px]] |
| | | |
| ===Set/Check Firewall=== | | ===Set/Check Firewall=== |
Line 45: |
Line 64: |
| | | |
| Go to <strong>Network > Firewall > General Settings</strong> WebUI section. Click on Edit button on WAN zone. | | Go to <strong>Network > Firewall > General Settings</strong> WebUI section. Click on Edit button on WAN zone. |
− | [[File:Network RUTOS manual lan as wan firewall general.png|border|class=tlt-border|1102px]]
| |
− | ----
| |
| | | |
| In WAN zone settings | | In WAN zone settings |
− | # Make sure that yours newly created interface is selected in Covered networks list.
| + | * Make sure that yours newly created interface is selected in Covered networks list. |
− | # Click Save & Apply.
| + | * Click Save & Apply. |
− | [[File:Network RUTOS manual lan as wan firewall zone.png|border|class=tlt-border|1102px]] | + | [[File:Firewall zones.png|border|center|class=tlt-border|859x422px]] |
| | | |
| ==Check new WAN interface== | | ==Check new WAN interface== |
Line 57: |
Line 74: |
| Insert WAN cable in selected port, go to <strong>Network > Interfaces</strong> WebUI section and if you followed steps correctly yours newly created WAN interface should be running and have an IP. | | Insert WAN cable in selected port, go to <strong>Network > Interfaces</strong> WebUI section and if you followed steps correctly yours newly created WAN interface should be running and have an IP. |
| [[File:Network rutos manual lan as wan check.png|border|class=tlt-border]] | | [[File:Network rutos manual lan as wan check.png|border|class=tlt-border]] |
| + | |
| + | ==Testing the configuration== |
| + | |
| + | Your device should now have two wired WAN connections. |
| + | |
| + | <ul> |
| + | <li>Set the Wired (WAN) interface as the main WAN connection.</li> |
| + | <li>Set the new interface as WAN [[RUT955_Failover|failover]] and save the changes. |
| + | <li>Go to [www.whatsmyip.com] and check your public IP address.<br></li> |
| + | <li>Then unplug the main WAN cable and check again. If the interface failed over correctly, the website should show a different IP address than before.<br></li> |
| + | <li>Plug the main WAN cable back in and wait a bit. Refresh the website; the IP should have change back to the one shown in the first place.</li> |
| + | </ul> |
| + | [[Category:LAN]] |
| + | [[Category:Update | hidden=yes]] |