Difference between revisions of "Setting up WAN as LAN"
From Teltonika Networks Wiki
(14 intermediate revisions by 8 users not shown) | |||
Line 1: | Line 1: | ||
− | |||
− | |||
==Introduction== | ==Introduction== | ||
− | This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for | + | This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RutOS devices (RUTX, RUT3, TRB1, TRB2). |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | == | + | ===Configuring WAN as LAN=== |
+ | * First you want to make sure that you have '''ADVANCED mode''' enabled. This will allow you to choose from a larger variety of settings. | ||
+ | [[File:Advanced mode rutOS.png|300px|border|class=tlt-border]] | ||
+ | ---- | ||
+ | * After that navigate to Network > Interfaces and '''disable WAN''' interface. | ||
+ | [[File:Network_interface_settings.png|200px|border|class=tlt-border]] | ||
+ | [[File:Interfaces disable wan.png|border|class=tlt-border|800px]] | ||
+ | ---- | ||
+ | * Next we will '''edit''' our LAN interface and navigate to '''Physical settings''' where we will add Interface item from the dropdown menu. | ||
+ | [[File:Physical settings of interface lan.png|border|1000px|class=tlt-border]] | ||
+ | ---- | ||
+ | * Select Ethernet Adapter item, by default it's '''eth1''' | ||
+ | [[File:Ethernet adapter in lan interface.png|border|class=tlt-border]] | ||
+ | ---- | ||
+ | * It should result in something like this. | ||
+ | [[File:Eth1 appears in lan interface.png|border|class=tlt-border|950px]] | ||
+ | ---- | ||
+ | * Once you're done with configurations above just '''save any changes you made'''. Now head to VLAN settings and check if WAN VLAN ID 1 is disabled, and ID 2 is untagged. | ||
+ | [[File:Vlan settings for wan as lan.png|border|class=tlt-border|900px]] | ||
+ | ---- | ||
At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router. | At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router. | ||
− | |||
− |
Revision as of 13:41, 2 June 2020
Main Page > General Information > Configuration Examples > LAN > Setting up WAN as LANIntroduction
This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RutOS devices (RUTX, RUT3, TRB1, TRB2).
Configuring WAN as LAN
- First you want to make sure that you have ADVANCED mode enabled. This will allow you to choose from a larger variety of settings.
- After that navigate to Network > Interfaces and disable WAN interface.
- Next we will edit our LAN interface and navigate to Physical settings where we will add Interface item from the dropdown menu.
- Select Ethernet Adapter item, by default it's eth1
- It should result in something like this.
- Once you're done with configurations above just save any changes you made. Now head to VLAN settings and check if WAN VLAN ID 1 is disabled, and ID 2 is untagged.
At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router.