Difference between revisions of "Setting up WAN as LAN"
From Teltonika Networks Wiki
(13 intermediate revisions by 7 users not shown) | |||
Line 1: | Line 1: | ||
− | |||
− | |||
==Introduction== | ==Introduction== | ||
− | This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for | + | This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RutX devices. |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | ===Configuring WAN as LAN=== | |
− | [[File:Networking | + | * First you want to make sure that you have '''ADVANCED mode''' enabled. This will allow you to choose from a larger variety of settings. |
+ | [[File:Networking rutx manual webui basic advanced mode v1.gif|border|class=tlt-border]] | ||
+ | ---- | ||
+ | * After that navigate to Network > Interfaces | ||
+ | [[File:Network_interface_settings.png|200px|border|class=tlt-border]] | ||
− | == | + | * Disable WAN interface |
+ | [[File:Interfaces disable wan.png|border|class=tlt-border|1100px]] | ||
+ | ---- | ||
+ | * Next we will '''edit''' our LAN interface and navigate to '''Physical settings''' where we will add Interface item from the dropdown menu. | ||
+ | [[File:Physical settings of interface lan.png|border|1100px|class=tlt-border]] | ||
+ | ---- | ||
+ | * Select Ethernet Adapter item, by default it's '''eth1''' | ||
+ | [[File:Ethernet adapter in lan interface.png|border|class=tlt-border]] | ||
+ | ---- | ||
+ | * It should result in something like this. | ||
+ | [[File:Eth1 appears in lan interface.png|border|class=tlt-border|1100px]] | ||
+ | ---- | ||
+ | * Once you're done with configurations above just '''save any changes you made'''. Now head to VLAN settings and check if WAN VLAN ID 1 is disabled, and ID 2 is untagged. | ||
+ | [[File:Vlan settings for wan as lan.png|border|class=tlt-border|1100px]] | ||
+ | ---- | ||
At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router. | At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router. | ||
− | |||
− |
Revision as of 12:01, 3 June 2020
Main Page > General Information > Configuration Examples > LAN > Setting up WAN as LANIntroduction
This article provides a guide on how to configure WAN port as LAN. These configurations are specifically made for RutX devices.
Configuring WAN as LAN
- First you want to make sure that you have ADVANCED mode enabled. This will allow you to choose from a larger variety of settings.
- After that navigate to Network > Interfaces
- Disable WAN interface
- Next we will edit our LAN interface and navigate to Physical settings where we will add Interface item from the dropdown menu.
- Select Ethernet Adapter item, by default it's eth1
- It should result in something like this.
- Once you're done with configurations above just save any changes you made. Now head to VLAN settings and check if WAN VLAN ID 1 is disabled, and ID 2 is untagged.
At this point, WAN port should work as LAN. Go ahead and try to swap from your to current port to WAN, you should be able to ping the router.