Difference between revisions of "Domnev"

From Teltonika Networks Wiki
 
(292 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
<p style="color:red">The information on this page is updated in accordance with the [https://wiki.teltonika-networks.com/view/FW_%26_SDK_Downloads'''00.07.08'''] firmware version .</p>
 +
__TOC__
 
==Summary==
 
==Summary==
 +
This article contains instructions on how to send M-Bus data to the server using various protocols.
  
−
This chapter is a guide on configuring cobot.me provider '''hotspot''' instance on RUTX routers. This setup is also applicable to RUT series devices.
+
==Configuration overview & prerequisites==
−
==Step 1: cobot.me configuration ==
+
Before we begin, let's take a look at the configuration that we are attempting to achieve and the prerequisites that make it possible.
−
If you're having trouble finding this page or some of the parameters described here on your cobot account, you should turn on '''"Admin" mode'''. You can do that by clicking the "'''Admin'''" button at the top-right corner of the cobot website.
 
−
[[File:Cobotadmin.png|border|center]]
 
  
−
===Login===
+
'''Prerequisites''':
 +
* TRB143;
 +
* M-Bus device;
 +
* Server;
 +
* An end device (PC, Laptop, Tablet, Smartphone) for configuration;
 +
 
 +
 
 +
{{Template:Networking_rutos_manual_basic_advanced_webui_disclaimer
 +
| series = RUTX
 +
}}
 +
 
 +
 
 +
==Adding M-Bus devices==
 +
To add a new device to the configuration press [[File:Add Button.png|60x90px]] button which is shown below.
 +
 
 +
[[File:Mbus adding new device.png||border|class=tlt-border]]
 +
 
 +
===Device configuration===
 
----
 
----
−
First, go to '''cobot.me''' and log into your account ('''LOG IN''' in the top right corner). If you don't have a registered account then you will need to create one - click '''Try Cobot'''.
+
You will be granted to a new window. Configure your M-Bus device accordingly:
−
[[File:Cobotmain.png|border|center|1009x1009px]]
+
 
−
====Sign Up====
+
# '''Name''': Enter the desired name of the M-Bus device
 +
# '''Address type''': select which M-Bus address will be used
 +
# '''Primary/Secondary address''': specify M-Bus address
 +
 
 +
[[File:Mbus adding new device configuration v3.png|border|class=tlt-border]]
 +
 
 +
Test if the M-Bus device is reachable by a specified primary/secondary address. To do so click on [[File:Ping_device_option_mbus.png|110x110px]]. You might get on of two outputs:
  
−
After clicking '''Try Cobot''' you will be redirected to register page. Enter you account information and click '''Next'''.
+
* If you have specified correct primary/secondary address, you will receive:
−
[[File:Cobotsignup3.png|border|center]]
+
[[File:Mbus device pingable v2.png|border|class=tlt-border|300px]]
−
Next step is to enter further information of your account. After entering it click '''Add Space'''.
 
−
[[File:Cobotsignup5.png|center]]
 
  
 +
* If you have specified incorrect primary/secondary address, you will receive (if you do not know what address should be used, refer to the Scanning for available M-Bus devices (PRIDET URL) secion:
 +
[[File:Mbus device not pingable v2.png|border|class=tlt-border|300px]]
  
 +
Once finished, save the configuration by clicking [[File:Savenapply button.png|Savenapply button.png]].
  
−
===Set Up new radius server===
+
===Scanning for available M-Bus devices===
 
----
 
----
−
In the opened window click '''SETUP''' icon, then - '''Wifi Integration'''. You will be prompted to '''Radius Wifi Integration''' window. Click the '''Set up Radius Server.'''
 
−
[[File:Imagea.png|border|center]]
 
  
−
===Network details===
+
If you are not sure what address your M-Bus devices have, you can try scanning for the available M-Bus devices. To do so click on [[File:Scan button.png]] button.
  
−
You will be given your Radius server configuration data that you will need in the next step.
+
====Scan settings====
−
[[File:Radiuscobot.png|border|center]]
+
----
−
===Add Wifi Guest Accounts===
+
You will be granted to a new window. Configure scan settings accordingly:
  
−
Click '''Wifi Guest Accounts''' in the bottom of the page to add accounts to let users access your WiFi.
+
# '''Scan type''': select which M-Bus address will be scanned
−
[[File:Cobotwifi.png|border|center|1098x1098px]]
+
# '''Scan range''': From what M-Bus address scanning will start and M-Bus address until scanning will be performed.
 +
[[File:Mbus scan.png|border|class=tlt-border]]
  
 +
To start the scan click on [[File:Start scan button.png]] button.
  
−
Type user account information and click '''Add Account'''.
+
====Found devices====
−
[[File:Wifisuers.png|border|center|1095x1095px]]
+
----
 +
Once the scan is finished you should see the list of M-Bus devices that TRB143 were able to find:
  
 +
[[File:Mbus scanned devices add.png|border|class=tlt-border]]
  
−
At the bottom of the page you can see all your created users.
+
You can either [[File:Pencil2.png]] '''(1)''' M-Bus devices primary address or [[File:Add Button.png|60x90px]] '''(2)''' to the M-Bus devices list.
−
[[File:Accounts.png|border|center]]
 
  
−
==Step 2: Router configuration ==
+
==Gathering M-Bus data==
−
If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should '''turn on "Advanced WebUI" mode'''. You can do that by clicking the "Basic" button under "Mode", which is located at the top-right corner of the WebUI.
 
  
−
[[File:Networking_{{{series}}}_manual_webui_basic_advanced_mode.gif|border|class=tlt-border]]
+
If the device successfully added to the list, under the General settings you should see that the Status changes to <span style="color:green">Active</span>.
  
−
===Creating wireless access point===
+
[[File:Mbus status active v2.png|border|class=tlt-border]]
  
−
If you have already set up your wireless access point - skip this step.
+
===Data collecting groups===
 +
----
 +
To reach data collecting groups configuration press [[File:Pencil2.png]] button. [[File:Add Button.png|60x90px]] button lets you to create a new instance.
  
−
* Login to your router's WebUI. You can do this by entering the router's LAN IP address (192.168.1.1 by default) into the URL field of your web browser.
+
[[File:Mbus data collect overview.png|border|class=tlt-border]]
−
* Go to the '''Network → Wireless''' page.
 
−
* '''Click 'Add'''' to create a new Wireless Access Point. Depending on your needs, choose a 2.4 GHz ('''1''') or 5 GHz ('''2''') Access Point.
 
  
−
[[File:Wifirut.png|border|center]]
+
====Data collecting group instance====
 +
----
  
−
Edit your new Access Point as below:
+
Each data collection group contains the following information. Configure device accordingly:
  
−
# Check '''Enable;'''
+
# '''Enabled''': on
−
# Mode - '''Access Point''';
+
# '''Name''': desired name of the instance
−
# ESSID - Your desired Extended Service Set Identifier name;
+
# '''Period''': desired time duration between data retrievals
−
# Network - Choose the network you want to attach to this wireless interface or fill out the create field to define a new network.
+
# '''Data type''': desired data type to process the received data. Depending on your needs you can select between 5 different data types: '''JSON, XML, ASCII, Hexadecimal''' and '''Binary'''.
−
[[File:APconfig1.png|border|center]]
 
  
−
Navigate to '''Wireless Security''' tab and choose your '''Encryption''' method '''(1)'''. When you are done, click '''Save & Apply (2)'''.
+
[[File:Mbus data collect group v2.png|border|class=tlt-border]]
  
−
[[File:APsecu.png|border|center]]
+
You can check if your configuration works accordingly by pressing the [[File:Mbus test button.png]] button. You should see the data in a pop-up field:
−
===Set up hotspot===
 
  
−
Navigate to '''''Services''' → '''Hotspot''''' and add a new Hotspot Instance. To do so, find the '''Add New Instance''' section and select your Wireless AP in the interface list, then press '''Add'''.
+
[[File:Mbus TEST output.png|border|class=tlt-border]]
  
−
[[File:Hotspota.png|border|center]]
+
====Group values====
 +
----
 +
To reach group values configuration press [[File:Pencil2.png]] button:
  
−
'''Hotspot configuration'''
+
[[File:Mbus edit group values.png|border|class=tlt-border]]
  
−
In the '''General tab''' do the following steps:
+
There you can adjust additional settings:
  
−
# Check '''Enable;'''
+
# '''Enable''': Enable/disable data group value.
−
# Authentication mode - '''Radius'''.
+
# '''FCB toggle''': FCB (Frame Count-Bit), one-bit counter for reliable server-client communication.
−
[[File:Hotspotconfig2.png|border|center]]
+
# '''Manufacturer information''': Select to include manufacturer information in the payload.
 +
# '''Selected parameters''': Select to include the all parameters saved from device, or a custom subset of them. If the custom is selected you can specify '''frame''', '''record''' numbers and also a '''paramater'''
  
−
Then go to '''Radius''' tab and enter the Radius server configuration details from cobot:
+
[[File:Mbus device groupsa.png|border|class=tlt-border]]
  
−
# '''RADIUS Servers''' - 130.211.138.166, 104.198.250.153;
 
−
# '''Authentication port''' - 13143;
 
−
# '''Radius secret key''' - 4L1pnC5jMIlfZH2T;
 
−
# '''Save & Apply'''.
 
−
[[File:Hotspotconfiga.png|border|center|1258x1258px]]
 
  
−
==Test your Hotspot==
+
==Sending data to the server==
 +
This section contains information on how to send M-Bus data to the server using MQTT and HTTP protocols.
  
−
Try connecting to your router using computer or mobile phone.
+
===Data to Server configuration===
 +
----
 +
To set up Data to Server, navigate to Services → Data to Server. Enter desired name of the instnace and hit [[File:Add Button.png|60x90px]] button which is shown below.
  
−
Select the newly creating hotspot
+
[[File:Mbus data to server create.png|border|class=tlt-border]]
  
−
[[File:Wifimobile.png|border|center]]
+
===Data configuration===
 +
----
  
 +
[[File:Mbus data to server configuration.png|border|class=tlt-border]]
  
−
After successful connection visit any website. You should be redirected to hotspot login page.
 
  
−
Type your username and password.
+
Once finished configuring Data configuration tab click on [[File:Mbus data to server collection edit.png|160x160px]] button.
  
−
Click '''Login'''
+
===Collection configuration===
 +
----
  
−
[[File:Wifilogin.png|border|center|alt=|713x713px]]
+
[[File:Mbus data to server collection configuration.png|border|class=tlt-border]]
  
 +
Once finished configuring Collection configuration tab click on [[File:Mbus data to server server button.png|160x160px]] button.
  
−
You should see a message '''Authorization Successful'''
+
===Server configuration===
 +
----
  
−
[[File:Wifisuccess.png|border|center|alt=|713x713px]]
+
====HTTP configuration====
 +
----
 +
 
 +
[[File:Mbus data to server HTTP configuration.png|border|class=tlt-border]]
 +
 
 +
====MQTT configuration====
 +
----
 +
 
 +
[[File:Mbus data to server MQTT configuration.png|border|class=tlt-border]]
 +
 
 +
Once finished configuring Server configuration tab click on [[File:Savenapply button.png|Savenapply button.png]] button.
 +
 
 +
 
 +
==See Also==
  
 
==External links==
 
==External links==
−
http://www.cobot.me
+
[https://flespi.io/#/ Flespi.io]
−
 
 
−
[[Category:IoT]]
 

Latest revision as of 09:32, 22 August 2024

The information on this page is updated in accordance with the 00.07.08 firmware version .

Summary

This article contains instructions on how to send M-Bus data to the server using various protocols.

Configuration overview & prerequisites

Before we begin, let's take a look at the configuration that we are attempting to achieve and the prerequisites that make it possible.

Prerequisites:

  • TRB143;
  • M-Bus device;
  • Server;
  • An end device (PC, Laptop, Tablet, Smartphone) for configuration;


If you're having trouble finding this page or some of the parameters described here on your device's WebUI, you should turn on "Advanced WebUI" mode. You can do that by clicking the "Advanced" button, located at the top of the WebUI.

Networking rutos manual webui basic advanced mode 75.gif


Adding M-Bus devices

To add a new device to the configuration press Add Button.png button which is shown below.

Mbus adding new device.png

Device configuration

You will be granted to a new window. Configure your M-Bus device accordingly:

  1. Name: Enter the desired name of the M-Bus device
  2. Address type: select which M-Bus address will be used
  3. Primary/Secondary address: specify M-Bus address

Mbus adding new device configuration v3.png

Test if the M-Bus device is reachable by a specified primary/secondary address. To do so click on Ping device option mbus.png. You might get on of two outputs:

  • If you have specified correct primary/secondary address, you will receive:

Mbus device pingable v2.png

  • If you have specified incorrect primary/secondary address, you will receive (if you do not know what address should be used, refer to the Scanning for available M-Bus devices (PRIDET URL) secion:

Mbus device not pingable v2.png

Once finished, save the configuration by clicking Savenapply button.png.

Scanning for available M-Bus devices

If you are not sure what address your M-Bus devices have, you can try scanning for the available M-Bus devices. To do so click on Scan button.png button.

Scan settings

You will be granted to a new window. Configure scan settings accordingly:

  1. Scan type: select which M-Bus address will be scanned
  2. Scan range: From what M-Bus address scanning will start and M-Bus address until scanning will be performed.

Mbus scan.png

To start the scan click on Start scan button.png button.

Found devices

Once the scan is finished you should see the list of M-Bus devices that TRB143 were able to find:

Mbus scanned devices add.png

You can either Pencil2.png (1) M-Bus devices primary address or Add Button.png (2) to the M-Bus devices list.

Gathering M-Bus data

If the device successfully added to the list, under the General settings you should see that the Status changes to Active.

Mbus status active v2.png

Data collecting groups

To reach data collecting groups configuration press Pencil2.png button. Add Button.png button lets you to create a new instance.

Mbus data collect overview.png

Data collecting group instance

Each data collection group contains the following information. Configure device accordingly:

  1. Enabled: on
  2. Name: desired name of the instance
  3. Period: desired time duration between data retrievals
  4. Data type: desired data type to process the received data. Depending on your needs you can select between 5 different data types: JSON, XML, ASCII, Hexadecimal and Binary.

Mbus data collect group v2.png

You can check if your configuration works accordingly by pressing the Mbus test button.png button. You should see the data in a pop-up field:

Mbus TEST output.png

Group values

To reach group values configuration press Pencil2.png button:

Mbus edit group values.png

There you can adjust additional settings:

  1. Enable: Enable/disable data group value.
  2. FCB toggle: FCB (Frame Count-Bit), one-bit counter for reliable server-client communication.
  3. Manufacturer information: Select to include manufacturer information in the payload.
  4. Selected parameters: Select to include the all parameters saved from device, or a custom subset of them. If the custom is selected you can specify frame, record numbers and also a paramater

Mbus device groupsa.png


Sending data to the server

This section contains information on how to send M-Bus data to the server using MQTT and HTTP protocols.

Data to Server configuration

To set up Data to Server, navigate to Services → Data to Server. Enter desired name of the instnace and hit Add Button.png button which is shown below.

Mbus data to server create.png

Data configuration

Mbus data to server configuration.png


Once finished configuring Data configuration tab click on Mbus data to server collection edit.png button.

Collection configuration

Mbus data to server collection configuration.png

Once finished configuring Collection configuration tab click on Mbus data to server server button.png button.

Server configuration

HTTP configuration

Mbus data to server HTTP configuration.png

MQTT configuration

Mbus data to server MQTT configuration.png

Once finished configuring Server configuration tab click on Savenapply button.png button.


See Also

External links

Flespi.io

Retrieved from "https://wiki.teltonika-networks.com/index.php?title=Domnev&oldid=131099"